y1451 Steel machinist rulers 150 + 300 mm long
€4.90
Available
Product information "y1451 Steel machinist rulers 150 + 300 mm long"
For the optimal measurement of the chassis.
Steel rulers, 150 and 300 mm long.
Contents:
- 2 piece
Nauenweg 55
47805 Krefeld
Germany
Login
Customers also bought
Genuine HT spare/option part. Helpful tool for removal of clutch shoes, flywheels and many more.FitsZenoah G230/G240/G260/G270/G290/G320Chung-Yang enginesPT enginesLosi enginesHPI enginesThreadsize:M10 x 1Contents:1 piece
This pair of Tyres have the following use indications: HIGH GRIP situation for clean track. HIGH GRIP situation for big asphalt. HIGH GRIP situation for high temperatures. This pair of Tyres have the following technical features: REVO treated profile for the maximum traction and the maximum lateral grip. Treated profile studied to maintain the tyre surface alway clean from rubber murble. Compound exclusively developped for model tyres. Inside belt flexible but very strong, vulcanized directly together with tyre compound. Insert foam with special material for high temperatures, for maximum stability and high drive precision. Spoked wheel moulded with special material for high temperatures for maximum grip and stability. Special gluing system 100% guaranteed.The main sizes for this tyre are: WHEEL fixing with square 18mm. TYRE outside diameter 118mm. WHEEL inside diameter 90mm. TYRE tota width 65mm. Note:The harder a tire compound - the longer it lasts, but the more moderate the performance.The softer a tire compound - the better the performance, but the lower the durability. Hint!As a rule, the same tires can be used for front and rear.If the vehicle tends to oversteer, this can be avoided by using a harder front tire!In wet conditions you should use a rain tire which offers maximum grip under these circumstances.With the use of Magic Rain, a tire traction compound, the grip can be further improved.Check your tires after driving! It can happen that a tire starts to detach from the rim, in this case you should glue this spot immediately with our tire repair kit (y0067), otherwise the tire could detach completely from the rim.So find out which tire is the best for you!
Freaking expensive, but it is damned fine.ASONIC HQ 72-102 is a synthetic high-temperature lubricating grease, for use in limited slip differentials. Due to the careful selection of product components and the clean manufacturing environment, ASONIC HQ 72-102 is a rolling bearing grease with a particularly low noise level.Benefits for your application:High-temperature lubricating grease for rolling bearingsHigh purityLow noiseGood water resistanceContent:1 piece, tube with 30g
Content: 30 Gramm (€830.00 / 1000 Gramm)
This pair of Tyres have the following use indications: GOOD GRIP situation for clean track. GOOD GRIP situation for medium asphalt. GOOD GRIP situation for medium temperatures. This pair of Tyres have the following technical features: REVO treated profile for the maximum traction and the maximum lateral grip. Treated profile studied to maintain the tyre surface alway clean from rubber murble. Compound exclusively developped for model tyres. Inside belt flexible but very strong, vulcanized directly together with tyre compound. Insert foam with special material for high temperatures, for maximum stability and high drive precision. Spoked wheel moulded with special material for high temperatures for maximum grip and stability. Special gluing system 100% guaranteed.The main sizes for this tyre are: WHEEL fixing with square 18mm. TYRE outside diameter 118mm. WHEEL inside diameter 90mm. TYRE tota width 65mm. Note:The harder a tire compound - the longer it lasts, but the more moderate the performance.The softer a tire compound - the better the performance, but the lower the durability. Hint!As a rule, the same tires can be used for front and rear.If the vehicle tends to oversteer, this can be avoided by using a harder front tire!In wet conditions you should use a rain tire which offers maximum grip under these circumstances.With the use of Magic Rain, a tire traction compound, the grip can be further improved.Check your tires after driving! It can happen that a tire starts to detach from the rim, in this case you should glue this spot immediately with our tire repair kit (y0067), otherwise the tire could detach completely from the rim.So find out which tire is the best for you!
Item N° 8539 Measuring bench 740mm - 1pce.Allows a measuring of toe-in and adjusting of both sides the same time without changing the side. For an optimal usw you need 2 . Suitable for all FG models except Formula 1.
Genuine HT spare/option part. Ball & socket tool with t-handle, especially for installation and removal of balls in FG or Smartech/Carson cars' plastic a-arms and steering rod ball joints.Contents:1 piece
Customers also viewed
The Lightscale Camber Gauge is a black anodised alloy block that features 8 different angled planes in 0.5° steps from 0.5° to 4° on different surfaces. The gauge is to be layed down beside a tyre for negative camber angles and any 90° part is put on one of the planes an pulled towards the tyre. Doing so you can easily check the camber of your tyres. To check positive camber, just turn around the gauge. Turning the gauge upside down will make it a 10mm high block to support you measuring the droop of any 1/5, 1/6 and 1/10 scale Electric or nitro car. Those are usually put on 10mm support blocks and beeing measured their droop with a special tool. The Lightscale ride height gauge (50160200) is a droop gauge as well and will do the job for you.
Genuine HT spare/option part. Stainless steel protractor with 200 mm leg for angles up to 180°. Well-suited for measuring of camber or toe--in/toe-out on rc cars.Contents:1 piece
Item N° 8539 Measuring bench 740mm - 1pce.Allows a measuring of toe-in and adjusting of both sides the same time without changing the side. For an optimal usw you need 2 . Suitable for all FG models except Formula 1.
Genuine FG spare/option part. The rear disk brake is suitable for 1:5 models, Race-Trucks, the current version from Evo, 1:6 Off-Road and Monster models. The disk brakes prevent a breaking-out of the rear, have a very sensitive adjustment and are optically very effective. You can run the front disk brake with the gas servo, but make sure the servo has a minimun regulating power of six kilograms. We recommend to steer over two servos if you install front and rear disk brake. We deliver the disk brakes without uprights. In combination with the rim 6105/01 also suitable for Marder, Beetle and Pajero.Additional equipment for front and rear tuning disk brake:8472/01 Flexible bowden cables8474/05 Alloy bowden cable holder8469 Alloy guiding plate with ball bearing8479 Steel bush8448 Stud bolt for brake lining8458/02 Lasered tuning disk brake8457/03 Competition brake lining
Item N° 50353011Support Blocks for the Lightscale Droop Gauge front, 1 pce.This is an Alloy Support Block anodized in black colour with 30mm height.The Support Block is manufactured as a rectangle and so can used a 30mm, depending on which side you choose.The front block uses a single point of support while the rear one comes with two of those. Due to this 3 point support it is assured that even a little tweak in your chassis (none of them is 100% straight) will not affect the result of your measurement. Remove the wheels and tyres from your car and put the car onto the support blocks. Ideally the rear block is positioned to the back of car and the front one just where the servo saver is fixed to the chassis. The car is now propped on the support blocks safely and cannot bounce. Please make sure that no dirt or rubber is trapped between the Support blocks and the chassis.Now you can easily and correctly measure the droop of each axle and adjust the cars` tweak.To do so please use the Lightscale Droop Gauge (50835400)The use of Lightscales` Droop Gauge Support Blocks prevents incorrect measurements and therefore is absolutely reliable. Measurements which are done using a flat surface where the chassis is resting on, like you would use in the pits are usually incorrect due to a slightly tweaked chassis because dirt underneath the chassis will falsify the measurement and lead to a irregular setup. The use of Support Blocks which are based on 4 support points will result in the same incorrect results and downgrade the performance of your car which is why we 100% recommend the use of our support block because as racers ourselves we know all about the problems you may face.
Genuine FG spare/option part. The body shell is delivered unpainted, without decal set and rear wing.500 mm wheelbaseLength: 690 mmWidth: 385 mmHeight: 240 mmContents:1 piecePainting tips:
Robust quality, extremely stable (capable of carrying more than 30 kg), universally usable, multicolored, support surface can be opened, below 1 large compartment, as well as 1 removable insert approx. 36 x 16 cm with 2 yellow drawers below the support, divided into 5 or 7 compartments for small items 6 or 7 side insertion holes in different sizes for screwdrivers etc.Dimensions:approx. 50 x 32 x 32 cm