The Set contains the front body, the main body, the rear body, the spoiler-set and the body screws. The body shell is vac-formed from 2 mm Lexan. This body shell comes without pre-drilled mounting holes, it can be installed on all FG standard width touring car chassis' with 535 mm wheelbase, Carson C5 chassis and most other 1/5 touring cars with the same wheelbase.Set contains:FG 8180 Body shell set BMW M3 ALMS - 219,95 EURFG 8185/01 Vehicle decals BMW M3 ALMS - 50,50 EURy0683 Large Jägermeister decals - 29,90 EURSurcharge Jägermeister painting + glueing the decals - 195,90 EURRegular price: 496,25 EURThe set is delivered as shown.Required body mounts:Mount front: FG 7020/12 Front bumperRear body mount: FG 7152/01 Rear body mount Side body mount front: FG 7014 Body mountsSide body mount rear: FG 7014 Body mountsMeasures:Length: 890 mmWidth: 392 mmHeight: 260 mmWheelbase: 530 mm
Cable tie for one time tightening / sealing / fastening. For example on drive shaft boots, fuel hoses, brake lines and many more.With steel tongue for infinite adjustment and increased holding power. Especially for high demand applications.Size: 2.5 x 200 mmTemperature range: -40°C to +85°CContent: 20 pieces
Genuine Speed-Tec spare/option part. AN - expansion sealing gaskets are in use in the 2-stroke motor sports for years and are based on NBR-linked cellulose fibers. They are especially used for sealing hot oils, greases and fuels! The sealing material is compressed during assembly, and as soon as it comes into contact with fuel, it swells again. Thus it is i.e. possible to make up for irregularities in the sealed surfaces (i.e. cylinder / crankcase) and seal them properly! The material of the SPEED TEC AN - expansion sealing gaskets guarantees a very good dimensional accuracy and is often the solution for leaks on your engine! Technical data of the material in contact with fuel:- Rebound ASTM G > 30%; increase in thickness < 5%; weight gain < 55%;- Compressibility ASTM F36 G 22.5% +/- 2.5 27.5% +/- 7.5 The SPEED TEC AN - expansion sealing gaskets are available in the following versions:# ST-AN26V carburetor gasket 0,25/0,50 mm# ST-AN25I insulator gasket 0,25/0,50 mm# ST-AN24L air filter gasket 0,25/0,50 mm# ST-AN22 cylinder gasket, two bolt 0,25/0,50 mm# ST-AN42 cylinder gasket, four bolt 0,25/0,50 mm# ST-AN23G crank case gasket 0,25/0,50 mmContents:1 piece
Item N° y0675 Receiver battery pack 5000 mAh Ni-Mh - 1pce.Double-block special battery pack, 6 volt / 5000 mAh, with FG or universal connector.Dimensions: approx. 72 x 53 x 29 mmConnector:UniversalFGEspecially designed for the high current demand in FG 4WD cars NiMh battery pack, fits the stock battery tray.Can be used for FG Evo cars and Competition cars as well.The Sanyo eneloop cell eliminates the annoying problem that a charged battery has often lost a high percentage of its storage capacity after just one week. Also, the differences between individual cells in a pack are sometimes significant, reducing the life and performance of the complete pack. Compared to "normal" NiMh cells the Sanyo eneloop cell has a slightly lower capacity and a slightly higher price (in relationship to its capacity), but you get significant advantages in return. With the recently available improved version of the 2005 introduced and widely acclaimed eneloop cell self-discharge for rc-car related time frames is now more or less nonexistent. One could easily charge the cells at New Year?s Eve and use them at Christmas without noticing a significant loss of capacity. Sanyo eneloop cells show a considerably reduced tendency to failure of individual cells in a battery pack. Even after years eneloop cells usually differ by only a few percent. The voltage of the cells is also slightly higher than with normal NiMh cells, so that more volts are available under load. Especially when used in largescale cars with their usually extremely strong servos, this is a particularly important feature! Chargers which are suitable for NiMh cells will also work for eneloop cells. The basic features of the eneloop XX version are similar to the standard version, but here the priorities were set slightly different. At the expense of reduced (but easy to cope with for rc-car usage) values for load cycles and self-discharge, capacity could be increased by 25%.- Nominal capacity: 2500 mAh- Maximum number of charge cycles: 500- self-discharge: 25% at 1 yearYou can differentiate the two generations of eneloop cells by checking the model name which is written on each eneloop. The "old" cells have written HR-3UTG (AA) on them, the improved eneloop instead HR-3UTGA (AA)!
Please note:The usual spare parts supply is not yet available for these engines. Therefore the parts may come from disassembled new engines. Since every single engine is tested at the factory, the parts may show some minor signs of "use".
Special remover for Lexan (Polycarbonate) and for X- and XF-color, AS- and TS-color and many more painting system until 2-K color. Does not damage the body shell!For small corrections soak a cotton swap with Color ex. Use a lint-free cloth for large area applications.Color Ex comes in a glas bottle with child-proof bottle top.Contents:100 ml / 1 piece
Genuine FG spare/option part.For Zenoah G230/240/260/270/290 enginesApplications:Click here!Actual product may be of different color. We have no bearing on this since we are not the manufacturer.Please note:It is recommended to use a gasket sealer with every gasket on an engine. This gives better sealing anda longer lasting gasket. We also recommend:y0804 HT-flange sealer 518 y0994 Marston sealery0807 MD-Sil RTV silicone sealerContents:1 piece
Genuine Smartech spare/option part.Crankcase gasket for Smartech PT 23/28 cc engines. Actual product may be of different color. We have no bearing on this since we are not the manufacturer.Please note:It is recommended to use a gasket sealer with every gasket on an engine. This gives better sealing anda longer lasting gasket. We also recommend:y0804 HT-flange sealer 518 y0994 Marston sealery0807 MD-Sil RTV silicone sealerContent:1 piece
ST-EWP26V SPEED TEC 0,30 mm EWP207 carburetor gasketFor Zenoah G230/G240/G260/G270/G290Genuine Speed-Tec spare/option part. EWP207 is a gasket material based on NBR-bonded synthetic and organic fibres. It therefore has very good oil and fuel resistance and does not swell like other gaskets.EWP207 is ideally suited for sealing against cold and hot oils, greases and fuels. Features Oil resistant Heat repellent Does not swell Contents:1 piece
1 pair of Formula 1 tyres S1 on white GRP rims with 18 mm square, used. -Diameter 133 mm -width 65 mm See photos for condition and scope of delivery.Also for many off-road models such as FG and Carson with 18 mm square, who want to drive their vehicle on asphalt to protect their off-road tyres, as these are not suitable for this use.
1 pair of Formula 1 tyres S3 on white GRP rims with 18 mm square, used. -Diameter 133 mm -width 65 mm See photos for condition and scope of delivery.Also for many off-road models such as FG and Carson with 18 mm square, who want to drive their vehicle on asphalt to protect their off-road tyres, as these are not suitable for this use.
Genuine HT spare/option part.Cable tie for one time tightening / sealing / fastening. For example on drive shaft boots, fuel hoses, brake lines and many more.Specification:Size: 4,8 x 530 mmHolding strength: 25,8 kgTemperature range: -40°C to +85°CContents:20 piece
Genuine HT spare/option part. Cable tie for one time tightening / sealing / fastening. For example on drive shaft boots, fuel hoses, brake lines and many more.Size: 2.5 x 100 mmHolding strength: 8.1 kgTemperature range: -40°C to +85°CContents:1 piece
Genuine HT spare/option part. Cable tie for one time tightening / sealing / fastening. For example on drive shaft boots, fuel hoses, brake lines and many more.Specification:Size: 2,5 x 140 mmHolding strength: 18 kgTemperature range: -40°C to +85°CContents:100 piece
Genuine HT spare/option part. Cable tie for one time tightening / sealing / fastening. For example on drive shaft boots, fuel hoses, brake lines and many more.Specification:Size: 4,8x 360 mmHolding strength: 22 kgTemperature range: -40°C to +85°CContents:50 piece
The vehicle is being sold as used on behalf of a customer.
The original price is 1339 euros! The FG TR4E Truggy 4WD has only been run for 10 minutes and is in as good as new condition ! It is delivered without transmitter set. A powerful 55KG steering servo provides sufficient steering power. A TopTuning 700KV 4 pole brushless motor and a 200A Beast Pro speed controller are installed. You need a transmitter set, 2x4S batteries and a charger, then you're ready to go. Take a look at the photos. No matter where you perform with it and where you use it - with the FG TR4E you will be at the front of the pack! The E stands for electric power, the 4 for all-wheel drive. Extremely fast, powerful torque and all without noise. The TR4 is equipped with a powerful brushless motor and a controller. The electric power means extremely high torque, high top speed and all without engine noise. The Sportsline models are equipped with a powerful brushless motor and a brushless controller. Thanks to the built-in all-wheel drive, the models can be easily manoeuvred through any terrain without getting stuck. The controller can be easily adjusted via the transmitter or optionally via a programming card.
Fg 4 jaw Teflon clutch adjustable for FG, Carson, HPI, Losi and many other models with long adapter for Zenoah, CY or similar engines, used.See photos for condition and delivery.
Reliable and approved 4-block clutch with teflon linings, adjustable. The well approved clutch was reworked in some details. This clutch is excellent for the use in Off-Road models and is distinguised through reliability and low wear.-used.See photos for condition and delivery.Adjustable and in many details improved 4-block clutch.This clutch is suitable for all FG models and other brands with Zenoah or CY engines.Not suitable for HPI cars.
1 pair of PMT tyre Eclipse 15 on white BBS rim, used. Rim mount for 18 mm square. See photos for condition.
€9.90*
This website uses cookies to ensure the best experience possible. More information.... By clicking on "[Agree / Accept all / etc.]" you also give your consent to the disclosure of your behavior in our store to our partner, shopware AG (Ebbinghoff 10, 48624 Schöppingen, Germany), which cannot assign this data to you personally, but may process it for its own purposes (e.g. product improvements, market behavior analyses).