Rim with 18 mm square drive. Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable.1/6 monster truck tires, hard, glued on chromed FG Monstervrim. Outer Ø 210mm, width 120mm, fits FG Marder, Off-Road Buggy, Beetle and Monster cars. Fits other makes of 1/6 cars as well, wheel square size must be checked prior to installation. Installation of tires with a different diameter may require a change in gear ratio as well.Diameter 195 mm Width 120 mm 1 pair

Off-Road tires mounted and glued on rims, on chrome rims. Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable.Dimensions:Diameter: 150 mmWidth: 60 mmWheel square: 18 mmContents:4 pieces / 2 pairs

If you want a special combination of compounds please enter that information into the "note to us" form field at the end of the checkout process.The widening ring on the rear rim is glued on the outside.Mammoth Supergrip for 1/6 and 1/5 offroad cars. Fits too for Formular 1 models!Parking lot / race tires for your offroad car.VersionWidthOuter diameterFront64 mm153 mmRear78 mm153 mmGlued on genuine FG silver rims (rear tires using extension rings), with foam rubber inserts included. Rim has 18 mm square drive with reinforcement ring.Please note: based on experience we recommend against using other manufacturers rims and extensions. Since the Mammoth tires provide very good grip the rim and the bonding must withstand high loads. Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable.The Mammoth Supergrip is available in in the following compounds: Super softSoftMediumHardFront tirey0581y0582y0583y0584Rear tirey0591y0592y0593y0594General recommendation:The dirtier the track or the lower the ambient temperatures, the stickier (softer) the rear tires should be.Hint regarding the front tires: 2WD cars should use them one or two grades harder then the rears. 4WD cars usually like the same compound all around.Of course, the softer the tire the higher the wear rate; and this applies to Mammoth Supergrip onroad tires as well.The tires have a special onroad thread pattern but will still provide ideal traction after the pattern has been worn out. The white lettering on the tires has been applied for presentation purpose only. The tires will be delivered with black sidewall.Prices per unit: FrontRearMammoth Supergrip:Pair44,90 EUR49,90 EURTire inserts:Pair13,00 EUR13,00 EURFG rim:Pair14,90 EUR14,90 EURFG extension ring:Pair--.-- EUR14,90 EURMounting:Pair13,00 EUR13,00 EURTotal Price                                                                                            85,80 EUR    105,70 EUR = 191,50 EUR SETTotal for 1 pair each front and rear: 169,90 EUR================================Also suitable for:With the following wheel adapter: y1183 Rim adapter

Special version with vulcanized fabric reinforcement belt for extreme torque loads. GIANT GRIP belted 190 x 70 with black colored MadMax Extreme rims, 20-fold screwed, very tough, with 24 mm hex drive and reinforced orange beadlock rings for Losi 5ive-T and Desert-Buggy XL as well as all HPI Baja 5 B/T cars.The GIANT GRIP provides giant traction through 96 about one cm² wide and 5 mm high strong lugs, getting ample grip even on loose surfaces like sand and soil.Due to the extreme strain caused by the GIANT GRIP tires the MadMax rim with reinforcement ring had to be optimized once more.The GIANT GRIP tires come with strong special tire inserts which allow to transfer the power without canting, even on heavy cars like the Losi 5ive-T.Dimensions:Outer diameter: 190 mmTire width at bead 70 mmTread width 80 mmReinforced 24 mm hex wheel driveThe MadMax Giant Grip tires use 60 mm wide rims ( y1415/01 or y0761/01).The video shows the 18 mm square drive version. Also available with 24 mm hex. Some off-road tires knowledge can be found here!

Extra wide tire mounted and glued on genuine 1/6 scale FG buggy silver rims 3105/02 with silver extension ring 3106!Diameter 165 mm, width 80 mm. Fits all FG and Carson largescale cars, may fit other cars with 18 mm wheel squares as well.Available in three different compounds:softhard Unit price:- Mammoth tires extra wide: EUR 47.20 / pair- Mammoth inserts extra wide: EUR 9.90 / pair- genuine FG wide track rims 3105/02: EUR 14.90 / pair- genuine FG rim extension rings 3106: EUR 14.90 / pair- mounting + glueing rims / extensions / inserts / tires: EUR 13.00Total: EUR 99.90 Priced per pair.We have tried various rubber / tire compounds for several months on various forms of terrain, etc.. The Mammoth brings, due to its quite strong and large pins and the extreme width of the tire, especially on hard and low grip surfaces a high traction! The Mammoth is available in soft, medium and hard! The rule is: the harder the ground the softer the tire compound. Where other tires spin helplessly the Mammoth provides serious traction. With few exceptions, the Mammoth is usually for the rear axle only. The white lettering on the tires has been applied for presentation purpose only. The tires will be delivered with black sidewall. The disadvantage of Mammoth tires: Because of their extreme width they need to be mounted on FG wheels with extension rings and wide tire inserts (same as for the FG wide slicks), which is a labor intensive job. From experience, we must strongly recommend against using rims from another manufacturer in combination with extension rings. Due to the before mentioned traction no other rim has been up to the task! Broken rims and torn squares were the result. Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable.However, the original FG-rim lasts without problems!Also suitable for:With the following wheel adapter: y1183 Rim adapter

BIG DIGGER 170x60 with black MadMax Extreme rims with 20 beadlock screws, with 24 mm hex socket and reinforced orange beadlock rings for Losi 5ive-T and Desert Buggy XL as well as all HPI Baja 5 cars.The MadMax tires had 84, with more than 1 cm² cross-section and 6 mm tread depth, allow for best power transfer and provide excellent grip even on loose surfaces like sand or soil. Due to the extreme load created by the MadMax BIG DIGGER tires the rim was optimized again with a reinforcement ring.The tires are fitted with a special rigid insert, which can handle the cornering forces and maintain the tires shape even on heavy cars like the Losi 5ive-T.We recommend to check the beadlock screws after the run. Dimensions:Outside diameter: 170 mmFront tire width: 60 mmRear tire width: 80 mmReinforced 24 mm hex wheel drive The video shows the 18 mm square drive version. Also available with 24 mm hex. Some off-road tires knowledge can be found here!

The off-road tire for hard packed dirt and spectacular drifts!Gives great results on those carpets which are typical for some off-road tracks. 616 grippy square studs per tire, a total of more then 2.400 for a complete set of tires, guarantee maximum traction! The lower profile of the outer stud rows reduces lateral traction and guarantee exceptional directional stability and allows for spectacular drifts! Therefore the car is less prone to undesirable side rolls!The Narrow-Grip 616 tires are mounted on a flexible 10 spoke rim with steel ring reinforced 24 mm hex drive. 10 screws per beadlock ring keep the tires in place. The Narrow-Grip 616 tires feature a firm foam insert, making them suitable even for heavier weight cars.To prevent premature wheel drive wear the fit to the rim is very tight. Therefore the rim should be properly aligned with the hex drive and completely mounted via tightening the wheel nut! Attention: When using the Narrow-Grip wheels on a Super Losi Rock-Rey model, special wheel hexes are required. Also on FG and Carson models. For mounting on a Traxxas X-MAXX you need a set of special Top-Tuning wheel nuts. - TT1040 Top Tuning wheel hub 24mm/6-edge for Losi Super BajaRey/2.0 and Super Rock Rey for plastic axle stubs.  - AT-004 Atop wheel nuts 4 pieces Dimensions:Outer tire diameter: 180 mmTire and rim width: 60 mmRim inner diameter: 120 mmWeight for one tire: 430 grams / for a pair: 860 grams24 mm hex for Losi 5IVE-T, HPI Baja 5, MCD Wheels drives:24 mm hex for Losi 5IVE-T, HPI Baja 5 and MCD ccars.

You can select the tyre hardness above:  - Hurrax HX100 extreme Grip Medium 175/70 mm tyre and  - Hurrax HX400 extreme Grip Soft 175/70 mm tyre  Please select which tyre you prefer.  You also have the option of having the tyres delivered ready glued for an additional charge.  Please click if you want to have the tyres ready glued! HURRAX extreme is one of the most successful tire in large scale off-road racing and specifically designed for astro turf and solid ground. With more than 700 (!) differently designed, closely spaced lugs and the 70 mm wide tread it is reasonably wear resistant and provides optimal grip with good side traction. If this - i.e. on the front axle - is not desired, you may cut the lugs at the tires outer edge to reduce cornering grip. This can be easily done with a small side cutter or strong nail scissors. In order to reduce the edging in the tire on the front axle.This makes a tire less aggressive during cornering and changes the cars behavior towards understeer. It becomes depending on the track conditions (i.e. wet!) a lot more drivable.An optimal vehicle setup can often be achieved by running already used HURRAX extreme tires on the front and new ones on the rear axle.This is especially true for 2WD models. Dimensions:External diameter approx. 175 mmInner diameter approx. 130 mmWidth approx. 70 mmWeight: one glued tire on Hurrax rim: 470 gramsDue to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable. GRP off-road disc rim for tires with approx, 132 mm inner diameter.The closed disc rim features reinforcement ribs on the backside and a protective collar around the wheel nut seat.Dimensions:for tires with an inner diameter of approx. 132 mm and approx. 70 mm widthand an outer diameter of approx. 180 mm (like i.e. GRP / Gandini tires)Weight approx. 172 gramms

Ultragrip 170x80 and 170x60 on black MadMax Extreme rims with 20 beadlock screws, with 18 mm square socket and reinforced orange headlock rings for FG, Smartech and many more. 150 shifted long lugs and a central, 4 mm high ridge on the 60 mm wide front tire, and 210 pieces of square 6 x 4 mm studs on the 80 mm wide rear tire ensure optimal propulsion! The flattened profile structure of the rows of knobs reduces the directional control and guarantees an exceptionally good on-center feel! This makes the car less prone to unwanted traction rolls! Due to the extreme load created by the MadMax Ultragrip tires the rim was optimized again with a reinforcement ring.The tires are fitted with a special rigid insert, which can handle the cornering forces and maintain the tires shape even on heavy cars. The GPM Ultragrip are designed for use on sandy surfaces.We recommend to check the beadlock screws after the run. Dimensions:Outer diameter: 170 mmFront tire width: 60 mmRear tire width: 80 mmReinforced 18 mm square wheel drive Regular price EUR 177,40The video shows the 18 mm square drive version. Also available with 24 mm hex. Some off-road tires knowledge can be found here!

BIG DIGGER 170x60 with black MadMax Extreme rims with 20 beadlock screws, with 18 mm square socket and reinforced orange beadlock rings for FG, Smartech and many more. Due to the extreme load created by the MadMax BIG DIGGER tires the rim was optimized again with a reinforcement ring.The MadMax tires had 84 extremely strong, with more than 1 cm² cross-section and 6 mm tread depth, allow for best power transfer and provide excellent grip even on loose surfaces like sand or soil.The tires are fitted with a special rigid insert, which can handle the cornering forces and maintain the tires shape even on heavy cars. We recommend to check the beadlock screws after the run. Dimensions:Outer diameter: 170 mmFront tire width: 60 mmReinforced 18 mm square wheel drive The video shows the 18 mm square drive version. Also available with 24 mm hex. Some off-road tires knowledge can be found here!

Genuine UFRC spare/option part. Original equipment tires of the Ghost Rabbit GR1.Fits Losi MTXL as well.When using our special wheel nuts TT1020/02 these tires can also be mounted on the Traxxas X-Maxx.Tire with vulcanized Kevlar belt, speed resistant (no ballooning) and yet flexible.Rim with steel hex insert.Diameter 230 mm, width 100 mm, 24 mm hex wheel drive.Rim thickness at center hole: 8.75 mm.Hex depth: 8 mm.Weight: approx. 2160 grams/pairOn the Losi DBXL running these wheels requires the installation of the DBXL024 ATOP axle extenders!Contents:2 pieces

The Stadium Truck wheels are characterised by excellent grip and cornering stability. This is achieved thanks to a newly developed rubber compound. The tyres are suitable for firm surfaces such as clay and asphalt and can be used for a wide range of applications! The tyres are glued to Stadium chrome rims. The square depth of these Stadium wheels has been increased. This considerably reduces the risk of the rim square turning. An 18 mm rim square driver is required to fit the wheels. Due to the high torque load in relation to the bonding of tyres on large models, an occasional check and possibly a repair of the bonding (y0067) is essential.  Durchmesser x Breite / diameter x width 170 x 90 mm  Scope of delivery :  1 pair of Stadium Truck tyres S glued on chrome rims with 18mm square  1 pair of Stadium Truck tyres M glued on chrome rims with 18mm square 

The offroad tire combination!V-Pin front and Mammoth wide tires in rear are the unbeatable combination for offroad use.combi set:Mammoth ready glued: 99,90 EURV-Pin ready glued: 78,80 EURTotal: 178,90 EUROffer price: 99,99 EURDescription for V-Pin tires:The V-pin competition tire is particularly suitable for tracks with loose and sandy surface.The high tread profile, extended to the tire shoulder requires a high manufacturing cost.This tread design guarantees an extremely high side traction and provides maximum propulsion especially on surfaces like sand and loose soil for optimum. By cutting of the tread profile of the V-pin tires you can adjust your car's handling easily. The partly or nearly complete removal of the V-pin tire's tread on the outside of the tire, greatly affects the tire's side bite when cornering.Summarized: removing tread from V-Pin tires on the front axle will reduce oversteering, calm your car and make it easier to drive.When oversteering is extreme (e.g. high grass) you may even start cutting the tread on the inside shoulder. This can prevent your car from those annoying traction rolls.Diameter: 163 mmWidth: 65 mmPrices of the components V-Pin:V-Pin tires EUR 39.90 EUR / pairV-Pin tire inserts EUR 9.90 EUR / pairRims FG 6105/01 EUR 14.90 EUR / pairglue set y0067 EUR 13.30 EUR Total EUR 78.80 EUR Description for Mammoth tires:Extra wide tire mounted and glued on genuine 1/6 scale FG buggy rims 6105/01 with extension ring!The white lettering on the tires has been applied for presentation purpose only. The tires will be delivered with black sidewall. Diameter: 165 mmWidth: 80 mmRim with 18 mm square driveThe Mammoth brings, due to its quite strong and large pins and the extreme width of the tire, especially on hard and low grip surfaces a high traction! Where other tires spin helplessly the Mammoth provides serious traction. Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable.Combination for the HPI Baja and 5T cars will the rim extension rings glued on the inside!Unit prices Mammoth:Mammoth tires extra wide: 47.20 EUR / pairMammoth inserts extra wide: 9.90 EUR / pairgenuine FG wide track rims 6105/01: 14.90 EUR / pairgenuine FG rim extension rings 6436: 14.90 EUR / pairmounting + glueing rims / extensions / inserts / tires: 13.00 EUR Total: 99.90 EUR Mammoth ready glued: 99,90 EURV-Pin ready glued: 78,80 EURTotal: 178,90 EURIntroductory price: 99,99 EUR Also suitable for:With the following wheel adapter: y1183 Rim adapter

Genuine FG spare/option part. Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable.Contents:2 pieces/1 pair

Genuine FG spare/option part. The sides of the Monster Truck tires were reinforced and now we deliver these tires without fabric insert. The advantages are a better lateral traction and more grip.diameter x width: 210 mm x 115 mmThe set includes two tires and two tire inserts.Contents:2 pieces

Narrow Off-Road Buggy tires 60 mm, ready glued on rims. Suitable for all 1:6 Off-Road Buggies. To mount them on FG Off-Road models you need the 18 mm square wheel driver y0067. Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing () if necessary is unavoidable.Diameter: 180 mmWidth: 60 mmContents:2 pieces

Genuine FG spare/option part. Wide Off-Road Buggy tires 80mm, ready glued on rims. Suitable for all 1:6 Off-Road Buggies. To mount them on FG Off-Road models you need the 18 mm square wheel driver y6106/01. Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable.Dimensions:Diameter: 180 mmWidth: 80 mmContent:2 pieces

MadMax MAXI PIN tyres have been specially developed for carpet race tracks!  The special block tread pattern, with 480 knobs per tyre, provides excellent grip, but also puts extreme strain on the tyre and the rim.  To stabilise the tyre, the outside of the tyre shoulder is equipped with vertical ribbing on the side, which minimises tilting under load and counteracts the shear forces that occur in bends. Furthermore, the MAXI PIN tyres have knobs positioned on the side of the outer side, which particularly support the steering behaviour of your RC car in bends. Taken together, the MAXI PIN tyres provide maximum grip.  Dimensions:  Outer diameter: 185 mm  Tyre width at the outer edge of the tread: 75 mm  1 pair

Off-road tires for sandy underground! Gives great results on those carpets which are typical for some off-road tracks. 462 grippy square studs per tire, a total of more then 1800 for a complete set of tires, guarantee maximum traction! The lower profile of the outer stud rows reduces lateral traction and guarantee exceptional directional stability! Therefore the car is less prone to undesirable side rolls! The rim is the 6-spoke design with a steel reinforcement ring around the wheel drive. The NARROW-GRIP tires are available  with 24mm hex for Losi, HPI Baja 5 and Carson GP Wild Attack series cars and they allready glued!To prevent premature wheel drive wear the fit to the rim is very tight. Therefore the rim should be properly aligned with hex drive and completely mounted via tightening the wheel nut! Dimensions:Outer tire diameter: 175 mmTire and rim width: 62 mmRim inner diameter: 119 mmWeight for one tire: 375 grams / for a pair: 750 gramshe manufacturer of the Narrow-Grip 462 indicates that the use of these tires on very heavy models, like the Losi 5ive-T under heavy conditions, such as jumps and shifting / tilting of the chassis, may lead to breakage of spokes or hex socket. Due to this notice that kind of failure will not be compensated. We apologize for this note!As an alternative, we recommend our special offer for the Losi 5ive-T OEM tires and in particular all tire combinations with MadMax EXTREME rims or for Losi and HPI models: y1406/01 - Big Digger y1407/01 - Cross Bond y1408/01- Over Lander y1409/01 - Giant Grip y1417/01 - Ultra Grip Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (24 mm hex for Losi and HPI Baja 5 Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable. Wheels drives:18 mm square for FG & co.24 mm hex for Losi, HPI Baja 5 cars.Contents:2 pieces / 1 pair

You can select the tyre hardness above:  - Hurrax HX100 extreme Grip Medium 175/70 mm tyre and  - Hurrax HX400 extreme Grip Soft 175/70 mm tyre HURRAX extreme is one of the most successful tire in large scale off-road racing and specifically designed for astro turf and solid ground. With more than 700 (!) differently designed, closely spaced lugs and the 70 mm wide tread it is reasonably wear resistant and provides optimal grip with good side traction. If this - i.e. on the front axle - is not desired, you may cut the lugs at the tires outer edge to reduce cornering grip. This can be easily done with a small side cutter or strong nail scissors. In order to reduce the edging in the tire on the front axle.This makes a tire less aggressive during cornering and changes the cars behavior towards understeer. It becomes depending on the track conditions (i.e. wet!) a lot more drivable.An optimal vehicle setup can often be achieved by running already used HURRAX extreme tires on the front and new ones on the rear axle.This is especially true for 2WD models. Dimensions:External diameter approx. 175 mmInner diameter approx. 130 mmWidth approx. 70 mmWeight: one glued tire on Hurrax rim: 470 gramsDue to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable. GRP off-road disc rim for tires with approx, 132 mm inner diameter.The closed disc rim features reinforcement ribs on the backside and a protective collar around the wheel nut seat.Dimensions:for tires with an inner diameter of approx. 132 mm and approx. 70 mm widthand an outer diameter of approx. 180 mm (like i.e. GRP / Gandini tires)Weight approx. 172 gramms

1 pair of GRP offroad tyres soft with inserts.  - Diameter 180 mm  - width 70 mm  Profile see photos.

1 pair of GRP offroad tyres soft with inserts.  - Diameter 180 mm  - width 70 mm  Profile see photos.

The MadMax SUPERGRIP tires have been designed especially for use on tarmac. Even on fine-pored tarmac your car will still find enough grip! (As you can see in our video).On most 1/5 and 1/6 cars the best combination is the use of 60 mm wide front and 80 mm wide rear tires. The Losi 5ive-T Mini should run 60 mm wide MadMax SUPERGRIP tires all around, because the 80 mm wide SUPERGRIP tires are a bit too wide for the Mini body shell.The 80 mm wide MadMax tires are reinforced on the inside of the carcass with a special cross pattern in the tread section and ribs in the outside shoulder.MadMax SUPERGRIP tires are available in the following compounds: (embossed marking on the inside shoulder!)Breite:Soft:Medium:60 mm y1464/01y1464/0280 mm y1464/03y1464/04For running an rc-car on tarmac, the following recommendations apply:The dirtier the track or the colder the weather, the stickier (softer) the rear tires should be.A note for the front tires: 2WD cars should run slightly harder tires in front than in rear.On 4WD cars the same compound front and rear is usually a good choice!Of course, like in full scale motorsport it also applies to the MadMax SUPERGRIP tires that the softer the tire the higher the wear. The medium compound tire lasts significantly longer than the soft version!The MadMax SUPERGRIP has a special on-road tread. These tires have excellent grip even after eating up the tread and can be used after that for a long time as slicks! Some off-road tires knowledge can be found here!