Genuine Dynamite spare/option part.Key Features:Kills your 2-cycle gas engine on command, loss of radio signal, low battery, or total battery power lossComes ready to install no soldering requiredOptically Coupled to isolate your ignition system from your radio systemBuilt-in LED for easy-to-spot operational status3-Channel Radio System RequiredNot Compatible with AVC-Equipped ReceiversContents:1 piece

To protect a car from a crash in case the power supply fails is no easy task. The mechanical devices that are used to do the job are either bulky or cause a higher drain from the battery. The failsafe module is a more efficient way.The module controls the battery pack's voltage and takes control of the throttle servo when the voltage goes below 4.7 volts. As an additional feature you can supply a backup battery pack to power the throttle servo in case the main pack falls completely. The failsafe position of the throttle servo is adjustable.

Genuine TT spare/option part.Spare part for Killswitch TopTuning 0990 or Dynamite 1240. Also suitable for other projects at your own discretion.2-pole connection cable with silicone insulation and 22 AWG/0.32 mm² cross-section, length approx. 80 mm.Contents:1 piece

Failsafe unit with adjustable servo position, very low current drain (0.05mA). Excellent value for money!The circuit responds to failure of the control signals. When transmitter and receiver work correctly, the received control pulses determine deflection of the servos; but as soon as control pulses are missing, the circuit lets the connected servo run to a pre-set safety position. Thereby, loss of the model can be avoided.Attention: not compatible with digital servos!

Genuine TT spare/option part.Spare part for Killswitch TopTuning 0990 or Dynamite 1240. Also suitable for other projects at your own discretion.Plug-in mount for front panel installation, requires 8 mm diameter mounting hole.Contents:1 piece

Genuine TT spare/option part.Spare part for Killswitch TopTuning 0990 or Dynamite 1240. Also suitable for other projects at your own discretion.Set with 2 each red and black jumpers for 2.5 mm contact spacing.Contents:4 piece

A small, lightweight electronic module which is connected between the receiver and one servo of your AM or FM radio control system. If the radio control system should fail, the receiver suffer interference, or the voltage of the receiver battery fall to a dangerous level, the servo connected to the unit moves to a pre-selected position, e.g. full brake, and thereby prevents motor damage through over-revving.

Genuine TT spare/option part.Spare part for Killswitch TopTuning 0990 or Dynamite 1240. Also suitable for other projects at your own discretion.3-pole connection cable with PVC insulation and 24 AWG/0.2 mm² cross-section, length approx. 220 mm.Contents:1 piece

Genuine TT spare/option part.Spare part for Killswitch TopTuning 0990 or Dynamite 1240. Also suitable for other projects at your own discretion.Operating voltage 2.1 Volt, approx. 15 mA2-pole connection cable with PVC insulation and 24 AWG/0.2 mm² cross-section, length approx. 180 mm.Contents:1 piece

Genuine HT spare/option part.Failsafe unit with adjustable servo position, very low current drain (0.05mA). Excellent value for money!Attention: not compatible with digital servos!Contents:1 piece

Genuine HTspare/option part. The LiPo Voltage Checker provides a low voltage alarm for 28S cell counts.When the voltage is below the set value, an alarm will sound along with illuminating the red LED.The voltage checker will automatically detect the cell count when connected to the balance lead on 28S LiPo. SpecificationsInput: 1S (JST) and 28S (JST-XH) LiPo, Li-ION/LiMN/Li-FeUnit Voltage Display Range: 0.54.5 VTotal Voltage Display Range: 0.536 VTest Mode Voltage Range: 3.730 VAlarm Value Range: 2.73.8 V, including offDimensions: 3.9 cm x 2.4 cm x 0.9 cmContents:1 piece