Skip to main content Skip to search Skip to main navigation
EXTRA 20% off Outlet*. Use Code: EXTRA20 at checkout!!
+49 2151 820200 Mon-Fri 9 am - 6 pm, Sa 9 am - 1 pm

y1569 Low voltage buzzer with voltage test

Product information "y1569 Low voltage buzzer with voltage test"

Genuine HTspare/option part.

The LiPo Voltage Checker provides a low voltage alarm for 28S cell counts.
When the voltage is below the set value, an alarm will sound along with illuminating the red LED.

The voltage checker will automatically detect the cell count when connected to the balance lead on 28S LiPo.


Specifications

  • Input: 1S (JST) and 28S (JST-XH) LiPo, Li-ION/LiMN/Li-Fe
  • Unit Voltage Display Range: 0.54.5 V
  • Total Voltage Display Range: 0.536 V
  • Test Mode Voltage Range: 3.730 V
  • Alarm Value Range: 2.73.8 V, including off
  • Dimensions: 3.9 cm x 2.4 cm x 0.9 cm
Contents:
  • 1 piece

0 of 0 reviews

Average rating of 0 out of 5 stars

Leave a review!

Share your experiences with other customers.


Customers also viewed

Average rating of 0 out of 5 stars

DYNB5045H5 Dynamite Reaction 2.0 14.8V 5000mAh 4S 50C LiPo, Hardcase: EC5
Genuine Dynamite spare/option part. Dynamite's new Reaction 2.0 batteries come with all the power and performance you've come to expect from the original Reaction line, but now include a QR code directly on the battery label. You can scan the QR with the Dynamite Dashboard Smart Phone App for even quicker and easier setup. In addition, all Reaction 2.0 hardcase batteries now come in a sleek black color to better match whatever setup you use them in. Features: Balance Lead Length: 2.16 in (55mm) Battery Balance Connector: JST-XH Battery Type: LiPo Battery Voltage: 14.8V Capacity: 5000mAh Cell Configuration: 4S1P Charge Protection Circuitry: No Connector Type: EC5 Discharge Lead Length: 3.54 in (90.0mm) Hard Case: Yes Height: 1.89 in (48mm) Length: 5.47 in (139mm) Maximum Charge Current: 15A Maximum Charge Rate: 3C Maximum Continuous Discharge Rate: 50C Normal/Standard Charge Current: 5A Normal/Standard Charge Rate: 1C Watt Hours: 74.0Wh Width: 1.89 in (48mm) Wire Gauge: 12 AWG Contents:1 piece

€119.99*

Average rating of 0 out of 5 stars

Servo direct power supply cable, 1 pce.
servo_strom_ohne Application: y0363 - 2 servos, battery connector none,
Servo direct power supply cable, 1 pce.With this cable the servos get their current directly from the battery without straining the receiver circuit board.Silicone insulated wires with 0.5 mm² cross section

€12.90*

Average rating of 0 out of 5 stars

LOS255012 Losi Button Head Screws, M4 x 35 mm
Genuine Losi spare/option part. Contents:10 pieces

€7.99*

Average rating of 0 out of 5 stars

TT0990 Top Tuning Failsafe with kill switch and status LED for all transmitters
Genuine TT spare/option part.The new and improved failsafe modul.This kill switch module works with most FM and 2.4 GHz rc-systems. Not compatible with AVC-equipped receivers! You must have a free channel on your rc-system in order to install the module! This means at least a 3-channel radio for standard 1-servo brake/throttle setups or a 4-channel radio for dual brake servos driven by the radio's mixer function. With this module you can stop the engine with your radio. Additionally the module features a failsafe function which stops the engine when the rx-battery's voltage drops below a certain level or the rc-system has a glitch. A kill switch module fulfils two tasks. On the one hand, as a safety device, it is intended to shut off an engine with magneto ignition in case of failure of the remote control, and on the other hand, the engine can be stopped at any time by remote control.While the latter is mainly used for convenience, the safety aspect is what really matters.The failsave circuit integrated in all modern remote controls may brake the vehicle in the event of a radio interference, but this feature is dependent on the basic functionality of the receiver system and its power supply. However, if the receiver, the gas servo or the power supply fails completely, the failsave of the remote control can no longer do its job. The vehicle may be running haywire at full throttle.In these cases, the kill switch will cut the ignition of the engine and the vehicle will roll out without power.Features:Ready to install no soldering requiredRemote LED for easy-to-spot operational status (ignition live/killed)Optically coupled to isolate the ignition from the radio systemThreshold value for undervoltage protection (4V, 5V, 6V) adjustable with jumpers allows adaptation to the rx-battery type (LiPo, LiFePo, NiMH, NiCd)Contents:1 piece

€54.90*
Loading...
Upload in progress, please be patient ...
Shopware-Plugin Development Shopware-Plugin Development