Skip to main content Skip to search Skip to main navigation
EXTRA 20% off Outlet*. Use Code: EXTRA20 at checkout!!
+49 2151 820200 Mon-Fri 9 am - 6 pm, Sa 9 am - 1 pm

Futaba Failsafe Unit, F 1650 - 1pce.

Product information "Futaba Failsafe Unit, F 1650 - 1pce."

A small, lightweight electronic module which is connected between the receiver and one servo of your AM or FM radio control system. If the radio control system should fail, the receiver suffer interference, or the voltage of the receiver battery fall to a dangerous level, the servo connected to the unit moves to a pre-selected position, e.g. full brake, and thereby prevents motor damage through over-revving.

0 of 0 reviews

Average rating of 0 out of 5 stars

Leave a review!

Share your experiences with other customers.


Similar products

Average rating of 0 out of 5 stars

TT0990 Top Tuning Failsafe with kill switch and status LED for all transmitters
Genuine TT spare/option part.The new and improved failsafe modul.This kill switch module works with most FM and 2.4 GHz rc-systems. Not compatible with AVC-equipped receivers! You must have a free channel on your rc-system in order to install the module! This means at least a 3-channel radio for standard 1-servo brake/throttle setups or a 4-channel radio for dual brake servos driven by the radio's mixer function. With this module you can stop the engine with your radio. Additionally the module features a failsafe function which stops the engine when the rx-battery's voltage drops below a certain level or the rc-system has a glitch. A kill switch module fulfils two tasks. On the one hand, as a safety device, it is intended to shut off an engine with magneto ignition in case of failure of the remote control, and on the other hand, the engine can be stopped at any time by remote control.While the latter is mainly used for convenience, the safety aspect is what really matters.The failsave circuit integrated in all modern remote controls may brake the vehicle in the event of a radio interference, but this feature is dependent on the basic functionality of the receiver system and its power supply. However, if the receiver, the gas servo or the power supply fails completely, the failsave of the remote control can no longer do its job. The vehicle may be running haywire at full throttle.In these cases, the kill switch will cut the ignition of the engine and the vehicle will roll out without power.Features:Ready to install no soldering requiredRemote LED for easy-to-spot operational status (ignition live/killed)Optically coupled to isolate the ignition from the radio systemThreshold value for undervoltage protection (4V, 5V, 6V) adjustable with jumpers allows adaptation to the rx-battery type (LiPo, LiFePo, NiMH, NiCd)Contents:1 piece

€54.90*

Average rating of 0 out of 5 stars

DYNE1240 Dynamite Large Scale Safety Kill Switch
Genuine Dynamite spare/option part.Key Features:Kills your 2-cycle gas engine on command, loss of radio signal, low battery, or total battery power lossComes ready to install no soldering requiredOptically Coupled to isolate your ignition system from your radio systemBuilt-in LED for easy-to-spot operational status3-Channel Radio System RequiredNot Compatible with AVC-Equipped ReceiversContents:1 piece

€39.99*

Average rating of 0 out of 5 stars

TT0990/02 Top Tuning Futaba 2-pin male connector with cable for Failsafe
Genuine TT spare/option part.Spare part for Killswitch TopTuning 0990 or Dynamite 1240. Also suitable for other projects at your own discretion.2-pole connection cable with silicone insulation and 22 AWG/0.32 mm² cross-section, length approx. 80 mm.Contents:1 piece

€3.90*

Average rating of 0 out of 5 stars

Low voltage failsafe module, y0423 - 1pce.
To protect a car from a crash in case the power supply fails is no easy task. The mechanical devices that are used to do the job are either bulky or cause a higher drain from the battery. The failsafe module is a more efficient way.The module controls the battery pack's voltage and takes control of the throttle servo when the voltage goes below 4.7 volts. As an additional feature you can supply a backup battery pack to power the throttle servo in case the main pack falls completely. The failsafe position of the throttle servo is adjustable.

€49.30*

Average rating of 0 out of 5 stars

54004 SMD-Failsafe module
Failsafe unit with adjustable servo position, very low current drain (0.05mA). Excellent value for money!The circuit responds to failure of the control signals. When transmitter and receiver work correctly, the received control pulses determine deflection of the servos; but as soon as control pulses are missing, the circuit lets the connected servo run to a pre-set safety position. Thereby, loss of the model can be avoided.Attention: not compatible with digital servos!

€28.70*

Average rating of 0 out of 5 stars

TT0990/04 Top Tuning Plug-in mount for 5 mm LED for Failsafe
Genuine TT spare/option part.Spare part for Killswitch TopTuning 0990 or Dynamite 1240. Also suitable for other projects at your own discretion.Plug-in mount for front panel installation, requires 8 mm diameter mounting hole.Contents:1 piece

€3.90*

Average rating of 0 out of 5 stars

TT0990/05 Top Tuning Jumper Set Failsafe
Genuine TT spare/option part.Spare part for Killswitch TopTuning 0990 or Dynamite 1240. Also suitable for other projects at your own discretion.Set with 2 each red and black jumpers for 2.5 mm contact spacing.Contents:4 piece

€3.90*

Average rating of 0 out of 5 stars

TT0990/03 Top Tuning JR/universal 3-pin female connector with cable for Failsafe
Genuine TT spare/option part.Spare part for Killswitch TopTuning 0990 or Dynamite 1240. Also suitable for other projects at your own discretion.3-pole connection cable with PVC insulation and 24 AWG/0.2 mm² cross-section, length approx. 220 mm.Contents:1 piece

€3.90*

Average rating of 0 out of 5 stars

TT0990/01 Top Tuning Red illuminated 5 mm Led with cable for Failsafe
Genuine TT spare/option part.Spare part for Killswitch TopTuning 0990 or Dynamite 1240. Also suitable for other projects at your own discretion.Operating voltage 2.1 Volt, approx. 15 mA2-pole connection cable with PVC insulation and 24 AWG/0.2 mm² cross-section, length approx. 180 mm.Contents:1 piece

€3.90*

Average rating of 0 out of 5 stars

y0416 Hobbythek failsafe module
Genuine HT spare/option part.Failsafe unit with adjustable servo position, very low current drain (0.05mA). Excellent value for money!Attention: not compatible with digital servos!Contents:1 piece

€29.90*

Average rating of 0 out of 5 stars

y1569 Low voltage buzzer with voltage test
Genuine HTspare/option part. The LiPo Voltage Checker provides a low voltage alarm for 28S cell counts.When the voltage is below the set value, an alarm will sound along with illuminating the red LED.The voltage checker will automatically detect the cell count when connected to the balance lead on 28S LiPo. SpecificationsInput: 1S (JST) and 28S (JST-XH) LiPo, Li-ION/LiMN/Li-FeUnit Voltage Display Range: 0.54.5 VTotal Voltage Display Range: 0.536 VTest Mode Voltage Range: 3.730 VAlarm Value Range: 2.73.8 V, including offDimensions: 3.9 cm x 2.4 cm x 0.9 cmContents:1 piece

€9.90*

Customers also viewed

Average rating of 0 out of 5 stars

TT0990 Top Tuning Failsafe with kill switch and status LED for all transmitters
Genuine TT spare/option part.The new and improved failsafe modul.This kill switch module works with most FM and 2.4 GHz rc-systems. Not compatible with AVC-equipped receivers! You must have a free channel on your rc-system in order to install the module! This means at least a 3-channel radio for standard 1-servo brake/throttle setups or a 4-channel radio for dual brake servos driven by the radio's mixer function. With this module you can stop the engine with your radio. Additionally the module features a failsafe function which stops the engine when the rx-battery's voltage drops below a certain level or the rc-system has a glitch. A kill switch module fulfils two tasks. On the one hand, as a safety device, it is intended to shut off an engine with magneto ignition in case of failure of the remote control, and on the other hand, the engine can be stopped at any time by remote control.While the latter is mainly used for convenience, the safety aspect is what really matters.The failsave circuit integrated in all modern remote controls may brake the vehicle in the event of a radio interference, but this feature is dependent on the basic functionality of the receiver system and its power supply. However, if the receiver, the gas servo or the power supply fails completely, the failsave of the remote control can no longer do its job. The vehicle may be running haywire at full throttle.In these cases, the kill switch will cut the ignition of the engine and the vehicle will roll out without power.Features:Ready to install no soldering requiredRemote LED for easy-to-spot operational status (ignition live/killed)Optically coupled to isolate the ignition from the radio systemThreshold value for undervoltage protection (4V, 5V, 6V) adjustable with jumpers allows adaptation to the rx-battery type (LiPo, LiFePo, NiMH, NiCd)Contents:1 piece

€54.90*

Average rating of 0 out of 5 stars

y0416 Hobbythek failsafe module
Genuine HT spare/option part.Failsafe unit with adjustable servo position, very low current drain (0.05mA). Excellent value for money!Attention: not compatible with digital servos!Contents:1 piece

€29.90*

Average rating of 0 out of 5 stars

VP99635 Transmitter Battery Li-Po 7,4V 2200mAh
2-Cell 7.4V 2200mAh LiPo Transmitter BatteryThis is a transmitter only, rechargeable LiPo battery pack that fits some Futaba transmitters and also other radio brands. Fits Futaba Transmitters: T4PM T4PLS T4GRS T4PV T4PX T6KT7PX T7XC (tight fit) T8J T10JT10PX T12K T14SG T16SZ T18SZ FX20 FX36 Make sure the transmitter battery settings are for 2S LiPo with alarm cut-off set to 6.4 volt. Specs: Type: LiPo Transmitter Battery Power Connector: Futaba Power Wire: 22AWG Balance Connector: JST-XH Battery: 2S1P LiPo Nominal Voltage: 7.4V/2S Max Charge Voltage: 4.2V/Cell Mac Charge Current: 2.2A (1C) Capacity: 2200mAh Energy: 16Wh Storage Voltage: 3.7-3.8V/cell Size: Length: 73mm Width: 45mm Thickness: 15.5mm Weight: 98g Tech Notes: Charge the battery outside the transmitter with a LiPo balance charger equipped with an Futaba adapter lead and XH balancing connector Set the charger to "LiPo", 2s, 3.7v/cell

€28.90*

Average rating of 0 out of 5 stars

VOLZ-Servo, y1060 - 1pce. -Special offer-
Version 220 for steering and throttle/brakeOriginal price: 266,80?Gears: Metal - Steel output shaftBearings: 2x ball bearingWeight: 72gVoltage: 6,0 VoltsTorque: 220 Ncm Speed: 0,11 s. 40ºDeflection: 2 x 45º

€99.90*

Average rating of 0 out of 5 stars

68504 FG Conversion kit FG monster/stadium truck/hummer 2WD 535 to 4WD.
For converting the FG Monster/Stadium Truck 535 2WD into a model with 4WD drive.The conversion kit contains all chassis parts and drive parts required for the conversion, except for differential grease.

€254.90*
Loading...
Upload in progress, please be patient ...
Shopware-Agency Shopware-Plugin Development