TT0990/05 Top Tuning Jumper Set Failsafe
€1.95
% €3.90 (50% saved)
Available
Product information "TT0990/05 Top Tuning Jumper Set Failsafe"
Spare part for Killswitch TopTuning 0990 or Dynamite 1240. Also suitable for other projects at your own discretion.
Set with 2 each red and black jumpers for 2.5 mm contact spacing.
Contents:
- 4 piece
Login
Customers also bought
These protective covers prevent the shock piston rods and seals for wear caused by dirt. They fit most 1/6 and 1/5 scale shocks.Not suitable for Gas Devil, Thunderbolt, Helldevil, CRT 4x4!- total length 150 mm for all FG / Carson / Smartech / Conrad and all dampers with a diameter from 22 to 30 mm. Set of 4
Shim rings to compensate the axial play of the shaft, to use as washers a.s.o.Part is delivered in silver or black color from vendor!
Shim rings to compensate the axial play of the shaft, to use as washers a.s.o.Part is delivered in silver or black color from vendor!
Genuine HPI spare/option part. Contents:4 pieces
Genuine TT spare/option part.Spare part for Killswitch TopTuning 0990 or Dynamite 1240. Also suitable for other projects at your own discretion.Operating voltage 2.1 Volt, approx. 15 mA2-pole connection cable with PVC insulation and 24 AWG/0.2 mm² cross-section, length approx. 180 mm.Contents:1 piece
Genuine rc-car-online spare/option part. Clemps for hydraulic brake linings with a outside diammeter of 4mm. e.g Colari, Magura II and Mecatech.Contents:8 pieces with mounting screws
Customers also viewed
Genuine Top Tuning spare/option part. Top Tuning The 20-amp Bigscale switch allows for a maximum input voltage of 30 volt. It is specifically designed as a receiver switch for use in combination with the Hitec HS-1005SGT servo and 4s receiver battery. The switch can also be used for other applications at your discretion with batteries up to 6S.Note: Top Tuning the electronic 20 amp Bigscale high voltage switch delivers the batterys full voltage. It does not replace a voltage regulator! The components which follow down the line (voltage regulator / servos / receiver) must be matched to this voltage! Using the latest MOSFET technology allows the 20 amp Bigscale high voltage switch to handle extreme loads, despite its small size. A blue LED status light clearly displays the activated mode. The 20 amp Bigscale high voltage switch is dust-and splash protected. He has an extremely low internal resistance and very low power consumption in off mode. Nevertheless it is recommended to unplug the battery when the model will not be used for an extended period. Properties:Voltage range: 3 to 30 VLoad: 20 ampsStandby consumption: 17 µAOperating temperature: - 15 ° C to +50 ° CCable length:Battery side 250 mmReceiver side 130 mmWeight: 13 gramsDimensions:Length: 29 mm Width: 13 mmHeight: 12 mmContents:1 piece
Genuine Smartech spare/option part.Module: m=1,5.Content:1 piece
Genuine TT spare/option part.Spare part for Killswitch TopTuning 0990 or Dynamite 1240. Also suitable for other projects at your own discretion.2-pole connection cable with silicone insulation and 22 AWG/0.32 mm² cross-section, length approx. 80 mm.Contents:1 piece
Genuine Dynamite spare/option part.Key Features:Kills your 2-cycle gas engine on command, loss of radio signal, low battery, or total battery power lossComes ready to install no soldering requiredOptically Coupled to isolate your ignition system from your radio systemBuilt-in LED for easy-to-spot operational status3-Channel Radio System RequiredNot Compatible with AVC-Equipped ReceiversContents:1 piece
High quality cnc machined parts made by GPM Racing Products from high strength billet aluminum. This extra long version is required for installation of GPM Cross Shocks on the front suspension of FG 4WD Monster cars.