TT0990/01 Top Tuning Red illuminated 5 mm Led with cable for Failsafe
Product number:
tt_tt0990_01
EAN:
4058575113997
Product information "TT0990/01 Top Tuning Red illuminated 5 mm Led with cable for Failsafe"
Genuine TT spare/option part.
Spare part for Killswitch TopTuning 0990 or Dynamite 1240. Also suitable for other projects at your own discretion.
Operating voltage 2.1 Volt, approx. 15 mA
2-pole connection cable with PVC insulation and 24 AWG/0.2 mm² cross-section, length approx. 180 mm.
Contents:
Spare part for Killswitch TopTuning 0990 or Dynamite 1240. Also suitable for other projects at your own discretion.
Operating voltage 2.1 Volt, approx. 15 mA
2-pole connection cable with PVC insulation and 24 AWG/0.2 mm² cross-section, length approx. 180 mm.
Contents:
- 1 piece
Login
Similar products
%
Genuine TT spare/option part.The new and improved failsafe modul.This kill switch module works with most FM and 2.4 GHz rc-systems. Not compatible with AVC-equipped receivers! You must have a free channel on your rc-system in order to install the module! This means at least a 3-channel radio for standard 1-servo brake/throttle setups or a 4-channel radio for dual brake servos driven by the radio's mixer function. With this module you can stop the engine with your radio. Additionally the module features a failsafe function which stops the engine when the rx-battery's voltage drops below a certain level or the rc-system has a glitch. A kill switch module fulfils two tasks. On the one hand, as a safety device, it is intended to shut off an engine with magneto ignition in case of failure of the remote control, and on the other hand, the engine can be stopped at any time by remote control.While the latter is mainly used for convenience, the safety aspect is what really matters.The failsave circuit integrated in all modern remote controls may brake the vehicle in the event of a radio interference, but this feature is dependent on the basic functionality of the receiver system and its power supply. However, if the receiver, the gas servo or the power supply fails completely, the failsave of the remote control can no longer do its job. The vehicle may be running haywire at full throttle.In these cases, the kill switch will cut the ignition of the engine and the vehicle will roll out without power.Features:Ready to install no soldering requiredRemote LED for easy-to-spot operational status (ignition live/killed)Optically coupled to isolate the ignition from the radio systemThreshold value for undervoltage protection (4V, 5V, 6V) adjustable with jumpers allows adaptation to the rx-battery type (LiPo, LiFePo, NiMH, NiCd)Contents:1 piece
%
tt_tt1000 Connector:
TT1000/01 Universal in - Universal out
Genuine Top Tuning spare/option part. Top Tuning The 20-amp Bigscale switch allows for a maximum input voltage of 30 volt. It is specifically designed as a receiver switch for use in combination with the Hitec HS-1005SGT servo and 4s receiver battery. The switch can also be used for other applications at your discretion with batteries up to 6S.Note: Top Tuning the electronic 20 amp Bigscale high voltage switch delivers the batterys full voltage. It does not replace a voltage regulator! The components which follow down the line (voltage regulator / servos / receiver) must be matched to this voltage! Using the latest MOSFET technology allows the 20 amp Bigscale high voltage switch to handle extreme loads, despite its small size. A blue LED status light clearly displays the activated mode. The 20 amp Bigscale high voltage switch is dust-and splash protected. He has an extremely low internal resistance and very low power consumption in off mode. Nevertheless it is recommended to unplug the battery when the model will not be used for an extended period. Properties:Voltage range: 3 to 30 VLoad: 20 ampsStandby consumption: 17 µAOperating temperature: - 15 ° C to +50 ° CCable length:Battery side 250 mmReceiver side 130 mmWeight: 13 gramsDimensions:Length: 29 mm Width: 13 mmHeight: 12 mmContents:1 piece
Genuine TT spare/option part.Spare part for Killswitch TopTuning 0990 or Dynamite 1240. Also suitable for other projects at your own discretion.2-pole connection cable with silicone insulation and 22 AWG/0.32 mm² cross-section, length approx. 80 mm.Contents:1 piece
The new TT0900 electric starter is pre-assembled and fits a wide range of models including the Losi 5ive-T, 5ive Mini and DBXL, most FG models, HPI-Baja / Wild Attack series etc. The TT0900 electric starter can be started with the remote control (free channel required!). The new TT0900electric starter has much more power than the previous Electric starter thanks to the brushless motor and higher voltage. The popular Zenoah G320 is no longer a problem. It also no longer uses a one-way bearing, which clearly increases reliability. Also the installation space has been noticeably reduced by the motor and a planetary gearbox.The starter components to be fitted weigh about 666 grams plus the battery.For mounting the starter, the flywheel on the engine is replaced by the version with spring-loaded pawls included in the delivery. The tools required for this, piston stopper and flywheel puller, are also included in the delivery.For the 3rd channel the transmitter should have a switch with two positions (momentary switch preferred) or a controller. An additional channel is required for a remote engine killswitch. A killswitch is included in the scope of delivery, but a real fail-safe module such as TT0990 offers higher safety. A possibly already existing failsafe module can also be used.Due to the splitting of the functions engine start and engine stop on two channels, no more compatibility problems with different remote controls are to be expected, only the availability of free channels matters.A 3S LiPo battery is required as the power source.In the shops options menu, we offer a special battery with a more compact design (5,600 mAh/30C, 110 x 49 x 34 mm) which makes installation usually easier in many cars, as well as a battery with standard dimensions (3,900 mAh/60C, 135 x 45 x 25 mm). Of course, other 3S batteries can also be used at your own discretion, but the load capacity (capacity x C-rate) should be on a similar or higher level.Please note that we cannot ship batteries to countries outside the European Union!Since the starter unit can be mounted vertically or horizontally and the brushless starter motor is very small, almost all air filters and most tuned pipe systems can be used.Notes regarding necessary modifications known to us for mounting the starter depending on the vehicle: FG 4wd onroad Rear r/h plastic body mount, depending on position, slightly modified or relocated FG 2wd onroad horizontal engine No modifications Mecatech FW01 No modifications FG 4wd Buggy sportsline Depending on the body shell, minor trimming is required. FG 2wd Buggy current chassis Depending on the body shell, minor trimming is required. FG 2wd Marder (old chassis) Starter fits without modifications to the chassis plate. However, the body shell has to be cut out a bit more seriously in the area of the starter. A repositioning of the rear r/h body mount is recommended. FG Monster Cut the r/h side panel slightly and add a flat area to the aluminum tube which supports the panel on the engine Losi 5ive-B Depending on the tuned pipe, mount starter with motor on top or on the l/h side. Losi 5ive-B Mount the starter motor on the l/h side, space for the tuned pipe is very tight and must be tested in each individual case. No problems when using the stock muffler box. Losi DBXL Depending on the tuned pipe, mount starter with motor on top or on the l/h side. If the starter motor is to be mounted on the side, one screw of the motor roll cage must be replaced by a CSH screw. Carson C5 Only with Zenoah or CY engine, not with Smartech PT engine (different hole pattern on engine)! Carson C6 With the C6, depending on the body shell, trimming is required. HPI 5B/T Depending on the body shell, minor trimming is required. Carson Wild GP Attack Depending on the body shell, minor trimming is required. The accommodation of the engine killswitch, controller unit and wiring harness must be carried out at your own discretion. User Manual FG 4WD On-Road FG Monster FG 2WD On-Road horizontal engine FG 2WD/4WD Buggy current chassis Losi 5ive-T Losi DBXL FG 2WD Marder (old chassis)
Genuine TT spare/option part.Spare part for Killswitch TopTuning 0990 or Dynamite 1240. Also suitable for other projects at your own discretion.Set with 2 each red and black jumpers for 2.5 mm contact spacing.Contents:4 piece
Genuine Top Tuning spare/option part. Set with four screws each M2,5x12 and M2,5x16.Contents:8 pieces
Genuine TT spare/option part.Spare part for Killswitch TopTuning 0990 or Dynamite 1240. Also suitable for other projects at your own discretion.Plug-in mount for front panel installation, requires 8 mm diameter mounting hole.Contents:1 piece
Genuine TT spare/option part.Spare part for Killswitch TopTuning 0990 or Dynamite 1240. Also suitable for other projects at your own discretion.3-pole connection cable with PVC insulation and 24 AWG/0.2 mm² cross-section, length approx. 220 mm.Contents:1 piece
Customers also viewed
Genuine HPI spare/option part. Content:30 cc / 1 piece
Content: 30 Milliliter (€329.33* / 1000 Milliliter)
