Item N° 6534/02 Throttle pivot post 3.1mm - setRevised set for 2 mm linkages, but with 3.1 mm pivot bore to prevent linkage seizing. Can be used for throttle or brake applications.Set collars have 2.1 mm inner diameter.

Genuine HT spare/option part. Protects the mated connection to prevent them from coming apart accidentally. Particularly recommended for direct power supply cords, as a tensile load on the cable can remove the link unnoticed and then you would perhaps think of a servo failure in the first place.The small size usually allows the installation even inside the receiver box.Also suitable for securing the connection of the receiver battery; the use of this clip means a big improvement in safety with little effort.Contents:1 piece

Genuine FG spare/option part. Splash-proofed receiver box for all merchantable small receivers, suitable for all car models 1:12 - 1:5.Dimensions:Length: upper section 92 mm, bottom 69 mmHeight: 48 mmWidth: 38 mmContents:1 piece

Genuine FG spare/option part. Suitable for rc-plate 5014.Dimensions:Inside length: 44 mmInside width: 20,5 mmContents:2 pieces

Genuine FG spare/option part. Suitable for all FG touring cars with short or medium wheel base.Dimensions:Total length: 225 mmMounting bolt distance: 190 - 210 mmContents:1 piece

Genuine FG spare/option part.Plastic bolt for battery holder.Contents:2 pieces

Genuine HT spare/option part.Very strong linkage with M6 steel ball joints.M6 threaded rod with lock nuts, balls with holes for M4 screws.Maximum length about 96 mm, but through cutting the M6 rod allows for a minimum length of 48 mm.Significantly stronger than the standard plastic version, and especially recommend when using the Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP servo, this linkage can be used with "normal" servos as well.The threaded rod is not designed as a turnbuckle for a reason because there is not need to change the adjusted length for this application after installation. The setting accuracy of 0.5 mm (½ turn) means a maximum difference to the ideal length of 0.25 mm. This is always sufficient, the trim on the transmitter handles the final adjustment.On the other hand, a connecting rod with the same thread on both ends will always keep its setting when installed, even when both lock nuts are not tightened against the ball joints. Therefore reliability is higher.Set includes:2 x steel ball joints M62 x flat lock nuts1 x M6 x 60 mm threaded piece for Losi 5ive-T1 x M6 x 80 mm threaded piece for Losi 5ive-T 2.02 x spacer tubesContents:1 piece

Genuine Top Tuning spare/option part. Top Tuning The 20-amp Bigscale switch allows for a maximum input voltage of 30 volt. It is specifically designed as a receiver switch for use in combination with the Hitec HS-1005SGT servo and 4s receiver battery. The switch can also be used for other applications at your discretion with batteries up to 6S.Note: Top Tuning the electronic 20 amp Bigscale high voltage switch delivers the batterys full voltage. It does not replace a voltage regulator! The components which follow down the line (voltage regulator / servos / receiver) must be matched to this voltage! Using the latest MOSFET technology allows the 20 amp Bigscale high voltage switch to handle extreme loads, despite its small size. A blue LED status light clearly displays the activated mode. The 20 amp Bigscale high voltage switch is dust-and splash protected. He has an extremely low internal resistance and very low power consumption in off mode. Nevertheless it is recommended to unplug the battery when the model will not be used for an extended period. Properties:Voltage range: 3 to 30 VLoad: 20 ampsStandby consumption: 17 µAOperating temperature: - 15 ° C to +50 ° CCable length:Battery side 250 mmReceiver side 130 mmWeight: 13 gramsDimensions:Length: 29 mm Width: 13 mmHeight: 12 mmContents:1 piece

Genuine HT spare/option part. Five antenna tubes with caps.Size: Length: 300 mmContent:1 set

Genuine FG spare/option part. Suitable for all FG touring car und Race-Truck models with long wheel base.Dimensions:Total length: 255 mmMounting bolt distance: 220 - 240 mmContent:1 piece

Genuine rc-car-online spare/option part. Versatile aluminum bracket for easy installation in panels or RC boxes with up to 4 mm wall thickness. Only a 6 mm hole is required and the bracket is fastened with the included nut. Alternatively, for installation in thicker material an M6 thread can be tapped as well. An O-ring provides a seal when installed in RC boxes.The bracket has a stepped hole into which the common antenna tubes of about 3.2/3.3 mm diameter can be inserted, but not pushed through. The hole for the antenna cable has a diameter of approx. 2.5 mm.The height of the bracket above the mounting surface is 16 mm.The scope of delivery includes an end cap and two antenna tubes with a length of approx. 170 mm.Contents:1 set

Genuine HT spare/option part. Abrasion protection for cables, fuel tubes and hydraulic brake lines. Pack with 1 m. Small, for cables from 1.5 to 8 mm diameter.Contents:1 piece / 1 meter

Genuine FG spare/option part. Bolts for 6815.Dimensions: 8 x 37,5 mm.Contents:4 piece

Genuine FG spare/option part. Dimensions:Wire diameter: 2 mmLength: 325 mmContents:1 piece

Genuine HT spare/option part.The adapter board is used for charging of 2S 6S batteries with XH, TP or HP connector on most current chargers with XH connector.Contents:1 piece

Original FG Ersatz-/Tuningteil. Spare part for 6118 and 6118/01.Contents:1 piece

Genuine HT spare/option part.For installation of the personal transponder.Contents:1 piece

Genuine HT spare/option part. This machined aluminum servo adapter allows easy installation of servos with a 69 x 18 mm mounting bolt pattern (for example Orange-Power, S8203) in vehicles / radio plates which provide a 75 x 18 mm mounting bolt pattern (for example Losi 5ive-T, Mini WRC, HPI Baja 5 series cars, many FG cars).The use of this adapter servo will neither tilt the servo, nor does it change installation height. Scope of delivery:1 x Servo mount adapter2 x Socket head cap screws 3 x 20 mm2 x Socket head cap screws 3 x 12 mm2 x Shim ring 3,2 mmContents:1 piece

Genuine FG spare/option part. Contents:2 pieces

Battery holder and pedestals for installation on chassis plates.BracketLength 157 mmWidth 24 mmDistance between mounting holes 140 mmPedestalsDiameter 8 mmHeight until top of platform 65 mmTotal height 75 mm

Genuine FG spare/option part. Accessories for FG switch no.: 6550 Switch f.receiver cable und 6551 Receiver cable with switch FG/JR.Contents:1 piece

Genuine FG spare/option part.Contents:1 set

Fits 5ive-T 2.0 as well!Set includes:y1307 Aluminum servo horn Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WPy1308/01 Aluminum servo mount A Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WPy1308/02 Aluminum servo mount B Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WPy1309 All steel linkage steering servo/servo saver applicationy1307 Aluminum servo horn Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP Losi 5ive-T, 5ive-B and MiniGenuine HT spare/option part.This extremely strong servo horn is specifically designed with dimensions for the installation of the Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP high-performance servo in the Losi 5ive-T and Mini for steering application, but it can be used in other cars with this kind of servo.It bolts directly to the servos stock aluminum disk.The lever of this arm is longer than that of the servo saver. This gives you faster actuating speed of the steering.A linkage with a double-sided arm can only be done properly if all corresponding levers are the same length and the linkages run exactly parallel. If this is not the case, the servo and servo saver shaft will try to change the distance to each other with every steering movement . Thus, undesirable constraining forces.For this reason we decided to give preference to the single-sided arm.Scope of delivery:1 x Aluminium servo horn4 x Socket head cap screws 3 x 14 mm1 x Socket head cap screws 4 x 30 mm1 x Self-lockinghexagon nut M44 x Shim ring 3,2Contents:1 piecey1308/01 + y1308/02 Aluminum servo mounts Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP Losi 5ive-T, 5ive-B and MiniGenuine HT spare/option part.These servo mounts allow for a simple and strong mounting of the Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP high power servo for steering application.The massive servo mounts bolt to the chassis using existing mounting holes. The mount for the stock servo has to be cut off the radio plate. The aluminum servo mounts feature a pair of additional mounting holes to install a stock servo should ever the need arise. The rear mount bolts to the radio plate as well, providing additional support for the plate.Scope of delivery y1308/01:1 x Mount A2 x Socket head cap screws 3 x 16 mm2 x Countersunk screw 4 x 14 mm2 x Shim ring 4,2 mmScope of delivery y1308/02:1 x Mount B1 x Socket head cap screw 3 x 25 mm1 x Socker head cap screw 3 x 16 mm2 x Countersunk screw 4x14 mm2 x Shim ring 3,2 mmContents:1 sety1309 All steel linkage for Losi 5ive-T and Mini steering servo/servo saver applicationGenuine HT spare/option part.Very strong linkage with M6 steel ball joints.M6 threaded rod with lock nuts, balls with holes for M4 screws.Maximum length about 96 mm, but through cutting the M6 rod allows for a minimum length of 48 mm.Significantly stronger than the standard plastic version, and especially recommend when using the Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP servo, this linkage can be used with "normal" servos as well.The threaded rod is not designed as a turnbuckle for a reason because there is not need to change the adjusted length for this application after installation. The setting accuracy of 0.5 mm (½ turn) means a maximum difference to the ideal length of 0.25 mm. This is always sufficient, the trim on the transmitter handles the final adjustment.On the other hand, a connecting rod with the same thread on both ends will always keep its setting when installed, even when both lock nuts are not tightened against the ball joints. Therefore reliability is higher.Set includes:2 x steel ball joints M62 x flat lock nuts1 x M6 x 60 mm threaded piece for Losi 5ive-T1 x M6 x 80 mm threaded piece for Losi 5ive-T 2.02 x spacer tubesContents:1 piece