LOS05008T1 Losi 1/5 DBXL ICON 2.0 4WD, 320 Zenoah incl. Mielke tuned pipe exhaust Buggy RTR incl. assembly

Only fuel from the gas station and off you go 100% RTR Incl. y0813/02 Motul 800 Racing Oil Off-Roadd One tank of gas 30 minutes Driving fun! Sufficient for the first 20 hours of driving 200 cm³ of oil per 5 liters of gas Including tuning parts worth over 100 euros The DBXL Platform has been a solid performer, and since its release, there have been minimal changes until now! Everything learned from the DBXL-E and DBXL-E 2.0 has directly been applied to the new and improved Losi® DBXL 2.0 4WD Gas RTR buggy. Built big and bold to deliver high-impact excitement, the DBXL 2.0 makes its presence known with a roaring new Zenoah® 32cc engine. A new high-flow air filter allows the engine to breathe to create maximum horsepower. This Losi 1/5th scale buggy powerhouse is designed to withstand the rigors of intense off-road driving with a full-time 4WD 5mm drivetrain, gearboxes, and heavy-duty construction that pulverizes the terrain at ballistic speeds. A brand-new steering rack and servo saver assembly keep your 2.0 tracking straight over any environment. A new radio tray, receiver box, and HV-rated servos take your DBXL 2.0 to the next level of performance. The DBXL 2.0 is also in for the long haul with a large-capacity tank for extended run times. The Losi DBXL 2.0 4WD Gas RTR is large-scale RC driving excitement at its most satisfying.Features Full 4WD drivetrain Pull Start Zenoah® G320 32cc 2-stroke gasoline engine Spektrum 3-channel SLT3 radio system Machined ring and pinion gear 800cc gas tank Integrated adjustable servo saver 4mm aluminum chassis Dual disk brakes Sealed differentials Icon Vehicle Dynamics and Magnaflow Liveries Zenoah® G320 32cc 2-stroke Gasoline EngineNew larger 32cc engine will provide the heart-pounding thrills you come to expect from a gasoline-powered engine. More displacement means more horsepower and more fun! New Center Pinned Outdrive CupsThe center drive cups have been redesigned so that they are now a ring captured design like the 5IVE-T, reducing the chances of drivetrain failures. 5mm Drive PinsTo put the power to the ground, we have increased the size of the outdrives and drive pins in all the dogbones to 5mm. They are still replaceable but now provide you the added strength and durability for the increased horsepower. Updated Gear BoxesProven on the DBXL-E 2.0, the gearboxes are now secured to the bulkheads with two screws to keep them from rocking up and down when power is applied. The gearboxes also allow for a more secure closure to better keep the pinion gear in place for increased strength and durability. Updated Steering Rack and Servo SaverUpdated helical design adds strength while providing a much smoother servo saver action for increased servo durability. Aluminum Shock Towers6mm thick Aluminum Front and Rear Shock Towers. Not only do these shock towers add durability/tunability to the DBXL 2.0, but they also add more tuning options to dial in your ride. Updated Shock BodiesUpdated shock bodies with a new lower aluminum cap allow for easier maintenance when changing out the shock O-rings. Updated Servo TrayNew servo tray allows you to run single or dual 1/5 scale steering servos as well as simplifying the throttle/brake linkage of easier tuning and adjustments. Updated Sway Bar LinksUpdated, larger, stronger sway bar links for added durability. New Chassis BracesNew dual rear chassis braces and torque rod increase chassis stiffness and durability Chassis Stiffening Plate4mm chassis stiffening plate under the engine allows for the use of engine slugs to set the gear mesh and reduce the chances of engine movement during large impacts. New Gas TankNew larger gas tank provides increased run time and a standard thread gas cap. New Center Differential Mount and Brake AssemblyConventional center differential mount allows for faster front and rear brake adjustments for improved handling. Authentic Motorsports Race Themed LiveriesMagnaflow Exhaust and Icon Vehicle Dynamics liveries LiPo Receiver PackThe included rechargeable 4000mAh 2S 7.4V Smart LiPo Receiver Battery allows for hours of playtime without stopping to re-charge Spektrum SLT3 Transmitter with Dual Protocol ReceiverA great low-cost radio system for bashers, crawler fans, and first-time drivers, the Spektrum 3-channel SLT3 with SR315 receiver goes beyond basic offering dependable SLT 2.4GHz control now, plus next-level DSMR® upgrade potential for the future. In The Box (1) DBXL 2.0 4WD Gas RTR (1) Spektrum SLT3 Transmitter with Dual Protocol (1) 4000mAh 2S 7.4V Smart LiPo Receiver Battery (1) Zenoah® G320 32cc 2-stroke gasoline engine (4) AA Batteries (1) User Manual (1) Miscellaneous Tools

Only fuel from the gas station and off you go 100% RTR Incl. y0813/02 Motul 800 Racing Oil Off-Roadd One tank of gas 30 minutes Driving fun! Sufficient for the first 20 hours of driving 200 cm³ of oil per 5 liters of gasThe DBXL Platform has been a solid performer, and since its release, there have been minimal changes until now! Everything learned from the DBXL-E and DBXL-E 2.0 has directly been applied to the new and improved Losi® DBXL 2.0 4WD Gas RTR buggy. Built big and bold to deliver high-impact excitement, the DBXL 2.0 makes its presence known with a roaring new Zenoah® 32cc engine. A new high-flow air filter allows the engine to breathe to create maximum horsepower. This Losi 1/5th scale buggy powerhouse is designed to withstand the rigors of intense off-road driving with a full-time 4WD 5mm drivetrain, gearboxes, and heavy-duty construction that pulverizes the terrain at ballistic speeds. A brand-new steering rack and servo saver assembly keep your 2.0 tracking straight over any environment. A new radio tray, receiver box, and HV-rated servos take your DBXL 2.0 to the next level of performance. The DBXL 2.0 is also in for the long haul with a large-capacity tank for extended run times. The Losi DBXL 2.0 4WD Gas RTR is large-scale RC driving excitement at its most satisfying.Features Full 4WD drivetrain Pull Start Zenoah® G320 32cc 2-stroke gasoline engine Spektrum 3-channel SLT3 radio system Machined ring and pinion gear 800cc gas tank Integrated adjustable servo saver 4mm aluminum chassis Dual disk brakes Sealed differentials Icon Vehicle Dynamics and Magnaflow Liveries Zenoah® G320 32cc 2-stroke Gasoline EngineNew larger 32cc engine will provide the heart-pounding thrills you come to expect from a gasoline-powered engine. More displacement means more horsepower and more fun! New Center Pinned Outdrive CupsThe center drive cups have been redesigned so that they are now a ring captured design like the 5IVE-T, reducing the chances of drivetrain failures. 5mm Drive PinsTo put the power to the ground, we have increased the size of the outdrives and drive pins in all the dogbones to 5mm. They are still replaceable but now provide you the added strength and durability for the increased horsepower. Updated Gear BoxesProven on the DBXL-E 2.0, the gearboxes are now secured to the bulkheads with two screws to keep them from rocking up and down when power is applied. The gearboxes also allow for a more secure closure to better keep the pinion gear in place for increased strength and durability. Updated Steering Rack and Servo SaverUpdated helical design adds strength while providing a much smoother servo saver action for increased servo durability. Aluminum Shock Towers6mm thick Aluminum Front and Rear Shock Towers. Not only do these shock towers add durability/tunability to the DBXL 2.0, but they also add more tuning options to dial in your ride. Updated Shock BodiesUpdated shock bodies with a new lower aluminum cap allow for easier maintenance when changing out the shock O-rings. Updated Servo TrayNew servo tray allows you to run single or dual 1/5 scale steering servos as well as simplifying the throttle/brake linkage of easier tuning and adjustments. Updated Sway Bar LinksUpdated, larger, stronger sway bar links for added durability. New Chassis BracesNew dual rear chassis braces and torque rod increase chassis stiffness and durability Chassis Stiffening Plate4mm chassis stiffening plate under the engine allows for the use of engine slugs to set the gear mesh and reduce the chances of engine movement during large impacts. New Gas TankNew larger gas tank provides increased run time and a standard thread gas cap. New Center Differential Mount and Brake AssemblyConventional center differential mount allows for faster front and rear brake adjustments for improved handling. Authentic Motorsports Race Themed LiveriesMagnaflow Exhaust and Icon Vehicle Dynamics liveries LiPo Receiver PackThe included rechargeable 4000mAh 2S 7.4V Smart LiPo Receiver Battery allows for hours of playtime without stopping to re-charge Spektrum SLT3 Transmitter with Dual Protocol ReceiverA great low-cost radio system for bashers, crawler fans, and first-time drivers, the Spektrum 3-channel SLT3 with SR315 receiver goes beyond basic offering dependable SLT 2.4GHz control now, plus next-level DSMR® upgrade potential for the future. In The Box (1) DBXL 2.0 4WD Gas RTR (1) Spektrum SLT3 Transmitter with Dual Protocol (1) 4000mAh 2S 7.4V Smart LiPo Receiver Battery (1) Zenoah® G320 32cc 2-stroke gasoline engine (4) AA Batteries (1) User Manual (1) Miscellaneous Tools

Genuine Losi spare/option part. Contrary to the Losi 5ive-T 2.0 ready-to-bind model the 5ive-T roller comes without rc-components (servos / receiver) and without engine / clutch / muffler / air filter.The Roller's body shell is also available in the painted versions for an additional surcharge!Contents:1 piece

When the original 5IVE-T was introduced the world of 1/5-scale off-road racing changed, and this iconic platform became one of the most successful and influential platforms to date. Now get ready for 2.0! The Losi 5IVE-T 2.0 BND: 1/5 4WD Gas Short Course Truck has all of the unrivaled performance of its predecessor and includes Bind-N-Drive technology, allowing you to pick the transmitter that best fits your lifestyle. The powerful Zenoah G320 32cc engine has been built specifically for the 5IVE-T 2.0.The revised chassis layout reduces the front drive shaft angle for improved durability and increased 4WD balance. Plus, the new rack style bellcrank steering assembly makes for easy Ackermann changes and overall improved steering geometry. Additional advances include an updated front hood, upgraded brakes, and hard anodized bleeder caps and shock bodies for improved shock performance. All this ensures the 5IVE-T 2.0 continues to reign supreme.Key FeaturesGenuine Zenoah G320 32cc engineInnovative Bind-N-DriveSpektrum 6200A DSMR 6-Ch AVC Telemetrie receiverImproved bar style steering rack with adjustable AckermannImproved center differential orientationImproved drive line angleHeavy-duty brakesInnovative clutch mount with gear mesh braceTough steering and gas/throttle servo braceExtra-large 800cc capacity fuel tank What's in the Box?Losi 5IVE-T® 2.0 BND 4WD SCTSpektrum® SR6000T 6-Channel DSMR Slim Receiver with TelemetryZenoah 32cc Gasoline Pull-Start EngineS900S 1/5 Scale Metal Gear Steering ServoS901T 1/5 Scale Metal Gear Throttle ServoWheel WrenchRod End/Shock End toolMulti WrenchSpark Plug WrenchBind PlugExhaust Gasket2.0mm, 2.5mm, 3.0mm, 4.0mm Allen WrenchesProduct Manual Dimensions Height: 181 mm Length: 965 mm Width: 520 mm Weight: 17 kg Needed to CompleteLipo Receiver Battery and Appropriate Charger like TT1530/252 or When the original 5IVE-T was introduced the world of 1/5-scale off-road racing changed, and this iconic platform became one of the most successful and influential platforms to date. Now get ready for 2.0! The Losi 5IVE-T 2.0 BND: 1/5 4WD Gas Short Course Truck has all of the unrivaled performance of its predecessor and includes Bind-N-Drive technology, allowing you to pick the transmitter that best fits your lifestyle. The powerful Zenoah G320 32cc engine has been built specifically for the 5IVE-T 2.0.The revised chassis layout reduces the front drive shaft angle for improved durability and increased 4WD balance. Plus, the new rack style bellcrank steering assembly makes for easy Ackermann changes and overall improved steering geometry. Additional advances include an updated front hood, upgraded brakes, and hard anodized bleeder caps and shock bodies for improved shock performance. All this ensures the 5IVE-T 2.0 continues to reign supreme.Key FeaturesGenuine Zenoah G320 32cc engineInnovative Bind-N-DriveSpektrum 6200A DSMR 6-Ch AVC Telemetrie receiverImproved bar style steering rack with adjustable AckermannImproved center differential orientationImproved drive line angleHeavy-duty brakesInnovative clutch mount with gear mesh braceTough steering and gas/throttle servo braceExtra-large 800cc capacity fuel tank What's in the Box?Losi 5IVE-T® 2.0 BND 4WD SCTSpektrum® SR6000T 6-Channel DSMR Slim Receiver with TelemetryZenoah 32cc Gasoline Pull-Start EngineS900S 1/5 Scale Metal Gear Steering ServoS901T 1/5 Scale Metal Gear Throttle ServoWheel WrenchRod End/Shock End toolMulti WrenchSpark Plug WrenchBind PlugExhaust Gasket2.0mm, 2.5mm, 3.0mm, 4.0mm Allen WrenchesProduct Manual Dimensions Height: 181 mm Length: 965 mm Width: 520 mm Weight: 17 kg Needed to CompleteLipo Receiver Battery and Appropriate Charger like TT1530/252 or Transmitter / receiver eg: DX2E or serial receiver compatible e.g: DX6R87-92 Octane Gasoline2-Cycle Motul Oil e.g: y0813/02Gas can e.g: Contents:1 piece

Includes HT-Edition parts set worth over 150.- , consisting of::SPMX40002SRX Spektrum LiPo battery 2S, 7,4V 30CTT1000 Top Tuning high voltage 30 Volt switchy0558 HT Car Bag XXLWhen the original 5IVE-T was introduced the world of 1/5-scale off-road racing changed, and this iconic platform became one of the most successful and influential platforms to date. Now get ready for 2.0! The Losi 5IVE-T 2.0 BND: 1/5 4WD Gas Short Course Truck has all of the unrivaled performance of its predecessor and includes Bind-N-Drive technology, allowing you to pick the transmitter that best fits your lifestyle. The powerful Zenoah G320 32cc engine has been built specifically for the 5IVE-T 2.0.The revised chassis layout reduces the front drive shaft angle for improved durability and increased 4WD balance. Plus, the new rack style bellcrank steering assembly makes for easy Ackermann changes and overall improved steering geometry. Additional advances include an updated front hood, upgraded brakes, and hard anodized bleeder caps and shock bodies for improved shock performance. All this ensures the 5IVE-T 2.0 continues to reign supreme.Key FeaturesGenuine Zenoah G320 32cc engineInnovative Bind-N-DriveSpektrum SR6000T telemetry-ready receiverImproved bar style steering rack with adjustable AckermannImproved center differential orientationImproved drive line angleHeavy-duty brakesInnovative clutch mount with gear mesh braceTough steering and gas/throttle servo braceExtra-large 800cc capacity fuel tank What's in the Box?Losi 5IVE-T® 2.0 BND 4WD SCTSpektrum 6200A DSMR 6-Ch AVC Telemetrie receiverZenoah 32cc Gasoline Pull-Start EngineS900S 1/5 Scale Metal Gear Steering ServoS901T 1/5 Scale Metal Gear Throttle ServoWheel WrenchRod End/Shock End toolMulti WrenchSpark Plug WrenchBind PlugExhaust Gasket2.0mm, 2.5mm, 3.0mm, 4.0mm Allen WrenchesProduct Manual Dimensions Height: 181 mm Length: 965 mm Width: 520 mm Weight: 17 kg Needed to CompleteAppropriate Charger like DYNC0505WTransmitter / receiver eg: DX2E or serial receiver compatible e.g: DX6R87-92 Octane Gasoline2-Cycle Motul Oil e.g: y0813/02Gas can e.g: y0686Contents:1 piece

The DBXL Platform has been a solid performer, and since its release, there have been minimal changes until now! Everything learned from the DBXL-E and DBXL-E 2.0 has directly been applied to the new and improved Losi® DBXL 2.0 4WD Gas RTR buggy. Built big and bold to deliver high-impact excitement, the DBXL 2.0 makes its presence known with a roaring new Zenoah® 32cc engine. A new high-flow air filter allows the engine to breathe to create maximum horsepower. This Losi 1/5th scale buggy powerhouse is designed to withstand the rigors of intense off-road driving with a full-time 4WD 5mm drivetrain, gearboxes, and heavy-duty construction that pulverizes the terrain at ballistic speeds. A brand-new steering rack and servo saver assembly keep your 2.0 tracking straight over any environment. A new radio tray, receiver box, and HV-rated servos take your DBXL 2.0 to the next level of performance. The DBXL 2.0 is also in for the long haul with a large-capacity tank for extended run times. The Losi DBXL 2.0 4WD Gas RTR is large-scale RC driving excitement at its most satisfying.Features Full 4WD drivetrain Pull Start Zenoah® G320 32cc 2-stroke gasoline engine Spektrum 3-channel SLT3 radio system Machined ring and pinion gear 800cc gas tank Integrated adjustable servo saver 4mm aluminum chassis Dual disk brakes Sealed differentials Icon Vehicle Dynamics and Magnaflow Liveries Zenoah® G320 32cc 2-stroke Gasoline EngineNew larger 32cc engine will provide the heart-pounding thrills you come to expect from a gasoline-powered engine. More displacement means more horsepower and more fun! New Center Pinned Outdrive CupsThe center drive cups have been redesigned so that they are now a ring captured design like the 5IVE-T, reducing the chances of drivetrain failures. 5mm Drive PinsTo put the power to the ground, we have increased the size of the outdrives and drive pins in all the dogbones to 5mm. They are still replaceable but now provide you the added strength and durability for the increased horsepower. Updated Gear BoxesProven on the DBXL-E 2.0, the gearboxes are now secured to the bulkheads with two screws to keep them from rocking up and down when power is applied. The gearboxes also allow for a more secure closure to better keep the pinion gear in place for increased strength and durability. Updated Steering Rack and Servo SaverUpdated helical design adds strength while providing a much smoother servo saver action for increased servo durability. Aluminum Shock Towers6mm thick Aluminum Front and Rear Shock Towers. Not only do these shock towers add durability/tunability to the DBXL 2.0, but they also add more tuning options to dial in your ride. Updated Shock BodiesUpdated shock bodies with a new lower aluminum cap allow for easier maintenance when changing out the shock O-rings. Updated Servo TrayNew servo tray allows you to run single or dual 1/5 scale steering servos as well as simplifying the throttle/brake linkage of easier tuning and adjustments. Updated Sway Bar LinksUpdated, larger, stronger sway bar links for added durability. New Chassis BracesNew dual rear chassis braces and torque rod increase chassis stiffness and durability Chassis Stiffening Plate4mm chassis stiffening plate under the engine allows for the use of engine slugs to set the gear mesh and reduce the chances of engine movement during large impacts. New Gas TankNew larger gas tank provides increased run time and a standard thread gas cap. New Center Differential Mount and Brake AssemblyConventional center differential mount allows for faster front and rear brake adjustments for improved handling. Authentic Motorsports Race Themed LiveriesMagnaflow Exhaust and Icon Vehicle Dynamics liveries LiPo Receiver PackThe included rechargeable 4000mAh 2S 7.4V Smart LiPo Receiver Battery allows for hours of playtime without stopping to re-charge Spektrum SLT3 Transmitter with Dual Protocol ReceiverA great low-cost radio system for bashers, crawler fans, and first-time drivers, the Spektrum 3-channel SLT3 with SR315 receiver goes beyond basic offering dependable SLT 2.4GHz control now, plus next-level DSMR® upgrade potential for the future. In The Box (1) DBXL 2.0 4WD Gas RTR (1) Spektrum SLT3 Transmitter with Dual Protocol (1) 4000mAh 2S 7.4V Smart LiPo Receiver Battery (1) Zenoah® G320 32cc 2-stroke gasoline engine (4) AA Batteries (1) User Manual (1) Miscellaneous Tools

With the Carson Wild Attack almost everything for driving (!) is included! The only exception: The fuel mixture from the gas station. (Recommended oil for mixing: y0813/02).The model includes the completely installed 2.4 GHz remote control, incl. transmitter alkalines, as well as a fail-safe system (automatic engine cut-off in case of possible malfunctions!), 20kg throttle servo and 35 kg steering servo, as well as a 2.000 mAh 6V receiver battery with charger and a tool set. Furthermore a spare air filter element and a special mixing canister. A detailed multilingual manual is also included. Here you will find an excellent, about 7 minutes duration introduction video to the Carson Wild Attack, which allows even the absolute novice for RC-Carswith combustion engine, the uncomplicated, problem-free entry: Technical details: approx. 70 km/h top speed0 - 70 km/h approx. 2.5 seconds With one tank of gas (700ccm) approx. 40 minutes driving time29cc engine, with pull starterSound reducing tuned pipe exhaust system2-shoe cltch with steel clutch bellA steel differential.Aluminium shocks, dust protectedbead-lock rims with off-road tyresaluminium rim driveradjustable rear wingCompletely ballraced 2WD drivetrain Water protected receiver boxventilated double disc brakealuminium chassis

Only fuel from the gas station and off you go 100% RTR Incl. y0813/02 Motul 800 Racing Oil Off-Roadd One tank of gas 30 minutes Driving fun! Sufficient for the first 20 hours of driving 200 cm³ of oil per 5 liters of gas Including tuning parts worth over 100 euros The DBXL Platform has been a solid performer, and since its release, there have been minimal changes until now! Everything learned from the DBXL-E and DBXL-E 2.0 has directly been applied to the new and improved Losi® DBXL 2.0 4WD Gas RTR buggy. Built big and bold to deliver high-impact excitement, the DBXL 2.0 makes its presence known with a roaring new Zenoah® 32cc engine. A new high-flow air filter allows the engine to breathe to create maximum horsepower. This Losi 1/5th scale buggy powerhouse is designed to withstand the rigors of intense off-road driving with a full-time 4WD 5mm drivetrain, gearboxes, and heavy-duty construction that pulverizes the terrain at ballistic speeds. A brand-new steering rack and servo saver assembly keep your 2.0 tracking straight over any environment. A new radio tray, receiver box, and HV-rated servos take your DBXL 2.0 to the next level of performance. The DBXL 2.0 is also in for the long haul with a large-capacity tank for extended run times. The Losi DBXL 2.0 4WD Gas RTR is large-scale RC driving excitement at its most satisfying.Features Full 4WD drivetrain Pull Start Zenoah® G320 32cc 2-stroke gasoline engine Spektrum 3-channel SLT3 radio system Machined ring and pinion gear 800cc gas tank Integrated adjustable servo saver 4mm aluminum chassis Dual disk brakes Sealed differentials Icon Vehicle Dynamics and Magnaflow Liveries Zenoah® G320 32cc 2-stroke Gasoline EngineNew larger 32cc engine will provide the heart-pounding thrills you come to expect from a gasoline-powered engine. More displacement means more horsepower and more fun! New Center Pinned Outdrive CupsThe center drive cups have been redesigned so that they are now a ring captured design like the 5IVE-T, reducing the chances of drivetrain failures. 5mm Drive PinsTo put the power to the ground, we have increased the size of the outdrives and drive pins in all the dogbones to 5mm. They are still replaceable but now provide you the added strength and durability for the increased horsepower. Updated Gear BoxesProven on the DBXL-E 2.0, the gearboxes are now secured to the bulkheads with two screws to keep them from rocking up and down when power is applied. The gearboxes also allow for a more secure closure to better keep the pinion gear in place for increased strength and durability. Updated Steering Rack and Servo SaverUpdated helical design adds strength while providing a much smoother servo saver action for increased servo durability. Aluminum Shock Towers6mm thick Aluminum Front and Rear Shock Towers. Not only do these shock towers add durability/tunability to the DBXL 2.0, but they also add more tuning options to dial in your ride. Updated Shock BodiesUpdated shock bodies with a new lower aluminum cap allow for easier maintenance when changing out the shock O-rings. Updated Servo TrayNew servo tray allows you to run single or dual 1/5 scale steering servos as well as simplifying the throttle/brake linkage of easier tuning and adjustments. Updated Sway Bar LinksUpdated, larger, stronger sway bar links for added durability. New Chassis BracesNew dual rear chassis braces and torque rod increase chassis stiffness and durability Chassis Stiffening Plate4mm chassis stiffening plate under the engine allows for the use of engine slugs to set the gear mesh and reduce the chances of engine movement during large impacts. New Gas TankNew larger gas tank provides increased run time and a standard thread gas cap. New Center Differential Mount and Brake AssemblyConventional center differential mount allows for faster front and rear brake adjustments for improved handling. Authentic Motorsports Race Themed LiveriesMagnaflow Exhaust and Icon Vehicle Dynamics liveries LiPo Receiver PackThe included rechargeable 4000mAh 2S 7.4V Smart LiPo Receiver Battery allows for hours of playtime without stopping to re-charge Spektrum SLT3 Transmitter with Dual Protocol ReceiverA great low-cost radio system for bashers, crawler fans, and first-time drivers, the Spektrum 3-channel SLT3 with SR315 receiver goes beyond basic offering dependable SLT 2.4GHz control now, plus next-level DSMR® upgrade potential for the future. In The Box (1) DBXL 2.0 4WD Gas RTR (1) Spektrum SLT3 Transmitter with Dual Protocol (1) 4000mAh 2S 7.4V Smart LiPo Receiver Battery (1) Zenoah® G320 32cc 2-stroke gasoline engine (4) AA Batteries (1) User Manual (1) Miscellaneous Tools

Genuine Mielke spare/option part.The tuned pipe system from premium manufacturer M. Mielke was specifically designed for Losi DBXL 2.0 in combination with large displacement and modified engines.The elaborate, angled design, makes best use of the available space in the DBXL 2.0 allowing for optimum performance! When designing the system, it was especially important to maximize the distance to the battery box of the DBXL 2.0 in order to minimize the thermal load on the battery. At the same time, the large distance improves access to Box. Contents:1 set

Includes HT-Edition parts set worth over 150.- , consisting of::SPMX40002SRX Spektrum LiPo battery 2S, 7,4V 30CTT1000 Top Tuning high voltage 30 Volt switchy0558 HT Car Bag XXLWhen the original 5IVE-T was introduced the world of 1/5-scale off-road racing changed, and this iconic platform became one of the most successful and influential platforms to date. Now get ready for 2.0! The Losi 5IVE-T 2.0 BND: 1/5 4WD Gas Short Course Truck has all of the unrivaled performance of its predecessor and includes Bind-N-Drive technology, allowing you to pick the transmitter that best fits your lifestyle. The powerful Zenoah G320 32cc engine has been built specifically for the 5IVE-T 2.0.The revised chassis layout reduces the front drive shaft angle for improved durability and increased 4WD balance. Plus, the new rack style bellcrank steering assembly makes for easy Ackermann changes and overall improved steering geometry. Additional advances include an updated front hood, upgraded brakes, and hard anodized bleeder caps and shock bodies for improved shock performance. All this ensures the 5IVE-T 2.0 continues to reign supreme.Key FeaturesGenuine Zenoah G320 32cc engineInnovative Bind-N-DriveSpektrum SR6000T telemetry-ready receiverImproved bar style steering rack with adjustable AckermannImproved center differential orientationImproved drive line angleHeavy-duty brakesInnovative clutch mount with gear mesh braceTough steering and gas/throttle servo braceExtra-large 800cc capacity fuel tank What's in the Box?Losi 5IVE-T® 2.0 BND 4WD SCTSpektrum 6200A DSMR 6-Ch AVC Telemetrie receiverZenoah 32cc Gasoline Pull-Start EngineS900S 1/5 Scale Metal Gear Steering ServoS901T 1/5 Scale Metal Gear Throttle ServoWheel WrenchRod End/Shock End toolMulti WrenchSpark Plug WrenchBind PlugExhaust Gasket2.0mm, 2.5mm, 3.0mm, 4.0mm Allen WrenchesProduct Manual Dimensions Height: 181 mm Length: 965 mm Width: 520 mm Weight: 17 kg Needed to CompleteAppropriate Charger like DYNC0505WTransmitter / receiver eg: DX2E or serial receiver compatible e.g: DX6R87-92 Octane Gasoline2-Cycle Motul Oil e.g: y0813/02Gas can e.g: y0686Contents:1 piece

Inclusive: Zenoah G320RC y0733 Big Scale-EXTREME, adjustable 3 - shoe clutch H105/01 Tuned pipe 2.0 for HPI - Baja 5B BUILD YOUR OWN ORIGINAL,AUTHENTIC HPI BAJA 5BHPI large scale fans, we have heard you! The one and only original HPI Baja 5B is BACK and ready for you to build from the ground up! The HPI SBK collection of Self Build Kits grows with the addition of not just one, but TWO 1/5th scale HPI kits! Fans of large scale off-road RC will be super excited to build their own gas-powered 1/5th scale Buggy with the HPI Baja 5B Self Build Kit!When the HPI Baja 5B buggy was first introduced, large scale RC was very expensive and quite difficult for the average RC hobbyist to experience. Using highly durable parts and innovative design features, HPI brought large scale off-road to new enthusiasts and ushered in a new, BIGGER era of RC!Now, YOU can build and own the legend! Experience the thrill and excitement of building a car which ends up being over 80cm (nearly 32 inches) long and weighing nearly 10kg (over 21 lb)! Just install your own engine and electronics as you build the HPI Baja 5B and you'll be ready for any adventure that comes your way!With extra-tough drivetrain parts like the viscous torque differential, super-durable composite spur gear with internal damping and all-metal drivetrain, the HPI Baja 5B is ready for your 23-32cc 2-stroke engine so you can experience the joy of gas-powered RC and up to 30-minute runtimes!The HPI Baja 5B is also equipped with extra-big and super-tough suspension parts, featuring awesome HPI durability! With its expertly designed molded composite suspension plus extra-long adjustable HD shocks, and massive high impact nylon 3-piece beadlock wheels, the Baja 5B is ready for full-speed racing on any off-road circuit!The 4mm thick 6061 aluminum monocoque chassis gives the HPI Baja 5B the classic desert racing buggy look. Precisely bent into shape for maximum strength, the chassis provides the mounting points for the engine and suspension, forming the backbone of the car. Precise steering is provided by a dual-bellcrank rack and cam-type servo saver. Aluminum parts are anodized in cool gunmetal and the classic Baja desert racer clear polycarbonate body is included in the SBK kit, ready for your custom racing scheme!The Baja 5B SBK is a great addition to your HPI collection, as well as a fabulous introduction to large scale buggies!RACING CHASSIS DESIGN & LAYOUTThe narrow channel chassis made from rigid 4mm 6061 aircraft aluminum and gives the HPI Baja 5B a classic desert racing buggy look and extreme stiffness and durability. The U-shaped chassis is protected at the rear with a thick plastic skid plate for extra protection to the motor and drivetrain.The tube roll cage is made of high impact nylon and topped with a real aluminum roof to carry on the classic looks. The roll cage is fully functional and protects the motor and internals from crash damage. The roll cage, radio box, body panels, wing, undertray and gear case are all mounted with fast access clips for easy maintenance. To finish you need: Remote control with servos and receiver battery Charger Two cans of Lexan paint Features Summary Unassembled 1/5th scale Off-Road Buggy Ready for your 23-32cc RC engine Ready for your electronics Enclosed radio box Baja desert racing body design Adjustable HD shock absorbers Monocoque chassis Low CG for superior handling Long travel suspension Viscous torque oil-filled gear differential All-terrain tires Beadlock wheels with metal insert hubs Aluminum rear shock tower Hard plastic skid plates Adjustable rear wing Quick access to all critical maintenance points Dual bellcrank steering Cam type servo saver Race spec Hex socket hardware Gunmetal anodizing Full set of rubber-sealed ball bearings Chassis Specifications Overall Length 817mm Height: 255mm Width: Front - 460mm; Rear - 480mm Tire Track (to center of tires): Front - 395mm; Rear - 400mm Wheelbase: 570mm Ride Height: 76mm Suspension Travel: Front - 95mm; Rear - 100mm Weight: 9.6kg (21.3lb) Adjustable Camber: front - shims; rear - screw Front caster: adjustable with shim 22 / 25.5* / 29 degrees (* stock) Toe-in: Front adjustable with tie rod; Rear adjustable with inserts 0-4 degrees (3 degrees stock set-up) Aircraft aluminum 6061 T6 monocoque chassis Double wishbone suspension with adjustable roll center F/R Drive system: HD metal gears with sealed gear box (8.382:1 gear ratio) Differential: viscous torque control with 4 pinion gears; sealed diff case with silicone oil Shock absorber: HD Aluminum coilover shock absorber with fully adjustable preload collar Wheel type: 3-piece beadlock design, high impact nylon material with inset heavy-duty metal hex hub

Big Bully GR1 - the new 4WD metal model from UFRC incl. RTR equipment! TT56112 Top Tuning Monster Brushless Motor 700 kV y1567 ZTW Beast Pro 200A ESC Spektrum DX6C 6-Channel DSMR Transmitter with SR315 Receiver 2 pieces y1570 CYS S0650 large scale servo, 55 kg/0,11 sec for Steering 2 pieces y2009 Top Tuning Digital pro Servo 25 kg for Differential lock Required for completion: 2 pieces of 6S batteries with EC8 connectors (total max. size for both batteries combined: length 193 mm × width 125 mm × height 100 mm) Charger for LiPo batteries Its external dimensions are not much bigger than those of a 1/6 car, yet its wheelbase is on par with many 1/5 cars and it has no overhangs at all; its tires fit a monster truck (230 mm diameter!). This results in amazing handiness for a large scale car combined with outstanding off-road capability. The GR1 comes out of the box almost as an all-metal vehicle. Tuning parts to reinforce the model are no longer necessary. Center and rear differential come standard with mechanical locks which can be activated independently by the radio. Of course, a radio system with the appropriate number of channels is required to use this feature. The dimensioning of all parts is designed for great reliability, e.g. the ball joints in the lower trailing arms are standardized industrial swivel bearings with an inner diameter of 6 mm, and the driveline can handle 12S hands down. But according to our experience, 12S operation is simply unnecessary. Nevertheless, we offer 12S equipment in the options menu. Oversized drive shafts also on the front axle are machined and hardened steel with fixed joints at both ends and sliding piece for length compensation. The tires feature a vulcanized fabric reinforcement made of Kevlar; ballooning is actually a thing of the past for them. Thanks to Kevlar, the fabric belt can be relatively thin, so the tires are soft and flexible despite the fabric. Aluminum servo arms for all 4 servos (steering and differential locks) are standard. The levers of the two steering servos are adjustable. Each steering servo has its own adjustable servo saver. A stainless steel adjustment tool is included. The Ackerman rod features four ball bearings. Shock absorbers with 8 mm piston rods and hard anodized shock bodies. All drive gears milled from steel and hardened. Two voltmeters can be optionally installed in the receiver box to monitor the traction batteries. The cage can be removed with only 4 clips, but even that is not a requirement for battery replacement. Inclusive original FG Monster Buggy body shell with rear wing. Big Bully GR1 (1/5 4WD solid rear axle)Main features of the 4WD Big Bully GR1: The strength of the components supports 12S power The wheelbase of 1/5 scale cars: 565mm The length of 1/6 scale cars: total length 790mm (when equipped with wheels with a diameter of 230mm) The whole car uses mostly metal parts, so there is no need to spend a lot of money on option parts later. The weight of the GR1 ready to run with 2x 4S/10.000 mAh batteries and 700KV motor is about 22 kg.But if you think now that this is a ponderous steamroller, you better think again. A "Tank on speed" is a better description. Despite the weight, wheelies can be called up at any time thanks to the appropriate gear reduction, even if the controller is only set to level two of four in acceleration (punch).At the same time, the possible twisting of the chassis is almost like that of a crawler. With the diff locks activated, the GR1 is almost unstoppable. Technical details: Drive train: full-time 4WD with 3 differentials (remote rear and center differential lock as standard equipment) Front suspension type: double a-arm IFS Rear suspension type: solid rear axle with 4-link suspension Scale: 1/5 Wheelbase: 565mm Front track width: 420mm Rear track width: 420mm Caster angle of kingpin: 20 degrees Front camber (adjustable): 3 degrees Toe-in (adjustable): 3 degrees Rear toe-in (not adjustable): 0 degrees Rear camber (not adjustable): 0 degrees Approach angle: about 90 degrees Departure angle: about 90 degrees Break-over angle: about 45 degrees Minimum turning radius: about 1.5 meters The maximum steering angle: about 30 degrees Maximum gradient: about 50 degrees Slide slope: about 40 degrees Maximum articulation: about 80 degrees (need to remove the front and rear anti-roll bars and loosen the angle limit screws of the front shock mounting beam) Lower trailing arm length (center/center of spherical bearings): 257 mm Chassis ground clearance (wheel diameter 230 mm): 115 mm Ground clearance under rear differential (wheel diameter 230 mm): 75 mm The maximum external dimensions of the vehicle body (length × width × height): 790 mm × 525 mm × 380 mm (with wheels of 230 mm diameter and 100 mm width) Gear ratio range: 9:1 to14.9:1 (The gear ratio can be changed by different gear set in the center gear box) Factory standard gear ratio: 14.9:1 Gear modulus: M1.5 Number of locking differentials: 2, servos for activation not included Locking differential positions: center and rear Wheel size: diameter 230 mm; width 100 mm. The tires feature Kevlar fiber belt to prevent ballooning and can handle 12S power Wheel drive size: 24 mm hex Front shocks mounting length (two-stage springs): 170 mm Front shock travel: 53 mm Rear shock mounting length (two-stage springs): 212mm Rear shock travel: 80 mm Calculated top speed: 8S power: 80 km/h (based on a 750KV motor) 12S power 110 km/h (based on a 680KV motor) (The maximum speed is calculated based on the electronic components and the actual numbers may vary) Weight of empty frame (excluding wheels and electronic components): 13.5 kg Total weight: approx. 22 kg Maximum payload of the frame: about 10 kg (do not press heavy objects or let people sit on the frame for driving operations, which may cause damage to parts) Lubricants parameters Front shock oil (silicone oil): 100cst Rear shock oil (silicone oil): 100cst Front differential oil (silicone oil): 300,000 cst Center differential oil (silicone oil): 300,000 cst Rear differential oil (silicone oil): 300,000 cst Front gearbox (grease): Swedish molybdenum disulfide high temperature grease (blue) Center gear box (grease): Swedish molybdenum disulfide high temperature grease (blue) Rear axle gearbox (grease): Swedish molybdenum disulfide high temperature grease (blue) (The above lubricants parameters are for reference only, and can be replaced according to your driving habits and environment) Frame materials and parts specifications, etc. Chassis Material: AL6061-T6 (aluminum) Processing technology: CNC machining, no stamp-out processing Surface treatment: hard anodizing and hardening Specifications: thickness 5 mm Front skid plate plate (standard configuration) Material: AL6061-T6 (aluminum) Processing technology: CNC machining non-casting Surface treatment: hard anodizing and hardening Specifications: thickness 5 mm Lower trailing arms Material: AL6061-T6 (aluminum) Processing technology: CNC machining Surface treatment: anodizing Specifications: The thickness of the part is 30 mm Front gear box housing Material: AL6061-T6 (aluminum) Processing technology: CNC machining Surface treatment: anodizing Specification: wall thickness 4 mm Center gear box housing Material: AL6061-T6 (aluminum) Processing technology: CNC machining Surface treatment: anodizing Specifications: wall thickness 2.5 mm Rear axle Material: AL6061-T6 (aluminum) Processing technology: CNC machining Surface treatment: anodizing Specifications: wall thickness 4 mm Front spindles Material: AL6061-T6 (aluminum) Processing technology: CNC machining Surface treatment: hard anodizing and hardening C-Hubs Material: AL6061-T6 (aluminum) Processing technology: CNC machining Surface treatment: hard anodizing and hardening Differential ring and pinion (front and rear) Material: high-strength billet gear steel, non-powder metallurgy Processing technology: CNC gear hobbing machine Heat treatment process: carburizing and hardening Modulus: M1.5 Center gear box spur gears Material: high-strength billet gear steel, non-powder metallurgy Processing technology: CNC gear hobbing machine Heat treatment process: carburizing and hardening Modulus: M1.5 Differential spider gears Material: steel-based powder metallurgy Processing technology: hot isostatic pressing sintering Heat treatment process: vacuum Differential locking clutch Material: high-strength billet carbon steel Processing technology: CNC Heat treatment process: carburizing and hardening Surface treatment: electroplating Front suspension drive shaft (CVD structure at the wheel end, universal joint structure at the gear box end) Material: high-strength billet carbon steel Processing technology: CNC Heat treatment process: carburizing and hardening Surface treatment: electroplating Specifications: CVD end shaft diameter 12 mm; gearbox end universal joint maximum outer diameter 32mm Center drive shaft Material: high-strength billet carbon steel Processing technology: CNC Heat treatment process: carburizing and hardening Surface treatment: electroplating Specification: shaft diameter 12 mm Rear universal drive shaft Material: high-strength billet carbon steel Processing technology: CNC Heat treatment process: carburizing and hardening Surface treatment: electroplating Specifications: The outer diameter of the spline telescopic shaft is 12 mm; the maximum diameter of the universal joint is 32 mm. Rear axle shafts Material: high-strength billet carbon steel Processing technology: CNC Heat treatment process: carburizing and hardening Surface treatment: electroplating Specifications: shaft diameter 12 mm, non-pin positive locking structure, shaft reaches into the differential planetary gear. Front bumper Material: high strength nylon Roll cage Material: high strength nylon Specification: diameter 10mm Car body shell Material: Polycarbonate Specifications: thickness 1.5 mm Original FG Monster Buggy body shell # 54150/01 with rear wing # 58150/02 Receiver box: nylon Front and rear shock absorption main parts Upper shock cap Material: AL6061-T6 (aluminum) Processing technology: CNC Surface treatment: anodizing Shock body Material: AL6061-T6 (aluminum) Processing technology: CNC Surface treatment: hard anodizing and hardening Specification: barrel diameter 28mm Shock spring Material: piano wire Surface treatment: black nickel plating Specification: front 2.8mm/rear 2.5mm Shock piston rod Material: high-strength carbon steel Processing technology: high precision grinding Heat treatment: carburizing and hardening Specification: diameter 8mm Spring perches Material: nylon Piston Material: nylon Processing technology: CNC machined, no injection molding Sealing ring Material: silicone Front shock mounting beam: AL6061-T6 (aluminum) Rear shock tower: AL6061-T6 (aluminum) Servo fixing frame: AL6061-T6 (aluminum) Steering rods Material: high-strength carbon steel Specification: 6mm Processing technology: CNC Heat treatment process: carburizing and hardening Surface treatment: electroplating Steering linkage rods Material: high-strength carbon steel Specification: 6mm Processing technology: CNC Heat treatment process: carburizing and hardening Surface treatment: electroplating Rear axle stabilizer bar Material: high-strength carbon steel Specification: 6 mm Processing technology: CNC Heat treatment process: carburizing and hardening Surface treatment: electroplating Ball heads Material: SUS304 stainless steel Specification: ball diameter 11 mm Front lower A-arm: high-strength nylon Center gear box mounts: AL6061-T6 (aluminum) Lower trailing arm brackets: AL6061-T6 (aluminum) Adjustable steering servo arm (comes as standard!): AL6061-T6 (aluminum) (adjustment angle 20 degrees) Wheels Specifications Diameter: 230 mm Width: 100 mm Hexagonal drive: 24 mm Material Rim: high-strength nylon Tire skin: natural rubber (Kevlar fiber belted) Liner: high elastic sponge Hex drive: The hex insert is powder steel metallurgy, and the outer reinforcement ring is SUS304 stainless steel All vehicle screws: 10.9 grade carbon steel General components: Wheels: Most 1/5 scale wheels with 24 mm hex drive and a diameter ranging from 190-230 mm and a width of 70-100 mm can be used. When the diameter is greater than 190 mm and the width is greater than 80 mm, the steering angle needs to be limited, and the steering angle has to be adjusted on the transmitter to about 75%. It is recommended to use wheels with a diameter of 230 mm and a width of 100 mm to maximize the performance and handling of the car. Differential spider gear assembly: HPI BAJA 5B compatible Nylon ball joints: 5ive-T size (ball diameter 11 mm) Electronic components configuration ESC Specification: 8S-12S Quantity: 1 Motor Specifications: market standard motor for 1/5 vehicles, such as 5692/56112/58113 When using 8S power, the motor KV value should be lower than 800. When using 12S power, the motor KV value should be lower than 600. When selecting a 12S motor, you should accurately consult whether it supports 12S power. Improper selection may cause serious damage to the motor. The diameter of the motor shaft is 8 mm, and the depth of the flat surface is 1 mm. The protruding length of the motor shaft should be greater than 20 mm and less than 40 mm. Quantity: 1 Battery 8S: 2 groups of 4S (6,000-12,000 mAh) in series 12S: 2 sets of 6S (6,000-12,000 mAh) in series When choosing a battery, it should be noted that the three-dimensional size of the two batteries together cannot be larger than the size of the battery compartment. Quantity: 2 packs Battery compartment size: length 193 mm×width 125 mm×height 100mm Steering servo: Specification (15T output shaft): 50-85 kg Use common 1/5 model servos (mounting bolt pattern 17.5 mm×75 mm). Quantity: 2 Differential lock servo Specification (25T output shaft): 15-35 kg Use common 1/8 model steering servos ( mounting bolt pattern 10.0 mm × 49.5 mm), it is recommended to use 25 kg steering gear, but it should not be stronger than 35kg, which may easily cause the displacement of the differential lock limiter and change the pulling stroke. The differential lock function fails. Quantity: 2 Remote control Type: car Channels: 5 channels or more (steering; throttle; differential lock uses two channels; car lighting (optional) channel) Quantity: one set Charger Type: Equipped with lithium battery balancing function Specifications: 4S or above Quantity: one set Battery safe storage container Common tools Tool type: Allen key wrench; Hex wrenches; circlip pliers Allen wrench Sizes (metric system): 1.5 mm; 2.0 mm; 2.5 mm; 3.0 mm; 4.0 mm; 5.0 mm Hex wrenches Sizes (metric system): 7 mm; 8 mm; 9 mm; 10 mm Circlip pliers Type: external circlip pliers (when gripping the handle of the circlip pliers, the front end should open outward) Specifications: The diameter of the tip is less than 1mm, and the use range is 4-10mm