AT-DBXL029/030/031 ATOP Front- and rear chassis braces, full set, for Losi DBXL 2.0

€109.90*

Product number: at_dbxl029_030_031

EAN: 4058575148739

Product information "AT-DBXL029/030/031 ATOP Front- and rear chassis braces, full set, for Losi DBXL 2.0"

Genuine ATOP spare/option part.

CNC-machined 6061-T6 aluminum chassis braces, for Losi DBXL 2.0.

Compared to the stock plastic parts (from sets # LOS251115 and LOS251116) the higher strength of the aluminum parts noticeably increases the chassis rigidity.

Contents:

1 piece

0 of 0 reviews

Leave a review!

Share your experiences with other customers.

Login

Your email address

Your password

Display reviews in current language only.

No reviews found. Share your insights with others.

Customers also bought

AT-DBXL02 ATOP aluminum front top chassis brace for Losi DBXL 2.0

Genuine ATOP spare/option part. CNC-machined 6061-T6 aluminum front top chassis brace; fits Losi DBXL 2.0.Stiffer than the stock plastic part (from set # LOS251115), the aluminum brace reduces chassis tweak in the area of the steering assy.Contents:1 piece

€39.90*

y1344 GPM Air filter cover for Losi Desert Buggy XL/2.0

GPM air filter cover which fits easily over your existing air filter. A fastening band band at the bottom holds the cover in place. Maintenance of the main filter will be significantly reduced, especially in very dusty environments.

€13.30*

TT0990 Top Tuning Failsafe with kill switch and status LED for all transmitters

Genuine TT spare/option part.The new and improved failsafe modul.This kill switch module works with most FM and 2.4 GHz rc-systems. Not compatible with AVC-equipped receivers! You must have a free channel on your rc-system in order to install the module! This means at least a 3-channel radio for standard 1-servo brake/throttle setups or a 4-channel radio for dual brake servos driven by the radio's mixer function. With this module you can stop the engine with your radio. Additionally the module features a failsafe function which stops the engine when the rx-battery's voltage drops below a certain level or the rc-system has a glitch. A kill switch module fulfils two tasks. On the one hand, as a safety device, it is intended to shut off an engine with magneto ignition in case of failure of the remote control, and on the other hand, the engine can be stopped at any time by remote control.While the latter is mainly used for convenience, the safety aspect is what really matters.The failsave circuit integrated in all modern remote controls may brake the vehicle in the event of a radio interference, but this feature is dependent on the basic functionality of the receiver system and its power supply. However, if the receiver, the gas servo or the power supply fails completely, the failsave of the remote control can no longer do its job. The vehicle may be running haywire at full throttle.In these cases, the kill switch will cut the ignition of the engine and the vehicle will roll out without power.Features:Ready to install no soldering requiredRemote LED for easy-to-spot operational status (ignition live/killed)Optically coupled to isolate the ignition from the radio systemThreshold value for undervoltage protection (4V, 5V, 6V) adjustable with jumpers allows adaptation to the rx-battery type (LiPo, LiFePo, NiMH, NiCd)Contents:1 piece

€54.90*

Details

AT-DBXL028 ATOP Aluminum rear uprights for all Losi DBXL/MTXL

Genuine ATOP spare/option part. CNC machined 6061-T6 aluminum rear uprights from ATOP to fit all Losi DBXL and MTXL versions, gasoline and electric.Significantly more rigid than the stock plastic version, this part contributes to increased directional stability. Plastic bushings for the hinge pins ensure reduced wear.Two additional mounting points are available for attaching the camber rods, allowing the model's handling to be better matched to the track.Comes with wheel bearings included. Contents:2 pieces

€79.90*

AT-DBXL026/027 ATOP Aluminum front spindles for all Losi DBXL/MTXL

Genuine ATOP spare/option part. One-piece CNC machined 6061-T6 aluminum spindles from ATOP, fits all Losi DBXL and MTXL versions, gas and brushless.Significantly more rigid than the stock plastic version, this part contributes to increased steering precision and directional stability. Stainless steel bushings for the King Pins are included.Comes with wheel bearings included. Contents:2 pieces

€149.90*

Similar products

DBXL024 ATOP Aluminum axle extenders all Losi DBXL / DBXL-E / 2.0 / MTXL, with closed nuts

Genuine ATOP spare/option part.CNC-machined from 6061-T6 aluminum by ATOP RC.Increases track width by 25 mm. Fits all versions of DBXL / DBXL-E / 2.0 (brushless and gas) and MTXL. 2 mm O-rings protect against drive pin loss.Set of four including O-rings, drive pins and closed wheel nuts (wrench size 24 mm!).Contents:1 set

€64.90*

Details

AT-DBXL001 ATOP Alloy spring retainer for Losi DBXL/XL-E +MTXL shocks

Genuine Atop spare/option part. Two pieces CNC-machined 6061-T6 aluminum spring perches for Losi DBXL. Direct replacement for the stock part (from set. # LOS 253006).Content:2 pieces

From €16.90*

Details

AT-DBXL002 ATOP aluminum camber rods/steering rods for Losi DBXL/DBXL-E

Genuine ATOP spare/option part. Camber rods for Losi DBXL with center section cnc-machined from 6061 aluminum by ATOP. High grade all-metal ball joints at the pivot points provide zero backlash and strength. Fits front and rear.Attention: On a DBXL-E 2.0 these rods can only be used as camber rods, not as steering rods! Dimensions: Hole to hole: 117mm Total length: 135mm Contents:2 pieces

€34.90*

Details

AT-DBXL026/027 ATOP Aluminum front spindles for all Losi DBXL/MTXL

€149.90*

AT-DBXL002/01 ATOP Spacer bushings for camber/steering rods of Losi DBXL and DBXL-E

Genuine ATOP spare/option part. Aluminum spacer bushings for the ball joints on camber and steering rods of Losi DBXL and DBXL-E.Content:8 pieces

€9.80*

AT-DBXL021 ATOP Aluminum front transmission mount for Losi DBXL/DBXL-E/2.0 + MTXL

Genuine ATOP spare/option part. Front transmission mount for Losi DBXL cnc-machined from 6061 aluminum by ATOP.Through the use of aluminum, the problem of torn out threads (incl. the front bumper installation) is eliminated. At the same time the chassis section under the transmission is strengthened and the mounting points for the shock towers are reinforced.Comes with all mounting screws included.This is the new ATOP version with the additional mounting points between transmission housing and transmission bracket for a more secure connection of these parts.Old and new versions are fully compatible, regardless of whether they are made of aluminum or plastic. The parts therefore fit all versions of DBXL and MTXL in any combination.However, the use of the additional mounting points requires the new version of both transmission housing and bracket!Contents:1 piece This article is identical to the article in the video!

€79.90*

AT-DBXL020 ATOP Complete Aluminum transmission case front / rear for Losi DBXL/DBXL-E/2.0 + MTXL

Genuine ATOP spare/option part. CNC-machined 6061 aluminum transmission case by ATOP, fits front and rear.Service life of ball bearings and ring & pinion will greatly benefit from the increased strength of this aluminum case. Comes with all mounting screws included.This is the new ATOP version with the additional mounting points between transmission housing and transmission bracket for a more secure connection of these parts.Old and new versions are fully compatible, regardless of whether they are made of aluminum or plastic. The parts therefore fit all versions of DBXL and MTXL in any combination.However, the use of the additional mounting points requires the new version of both transmission housing and bracket!Contents:1 piece This article is identical to the article in the video!

€139.90*

y0057 Ball & socket tool for Losi and HPI

Genuine HT spare/option part. Ball & socket tool with t-handle, special version for the ball joints.Fits Losi 5ive-T. 5ive-B, Desert Buggy XL, Desert Buggy XL-E, Monster Truck XL and the HPI Baja 5B and Baja 5R Ford Mustang.Contents:1 piece

€17.90*

AT-DBXL02 ATOP aluminum front top chassis brace for Losi DBXL 2.0

€39.90*

AT-DBXL016 ATOP aluminum steering rods for Losi DBXL-E 2.0

Genuine ATOP spare/option part. Steering rods for Losi DBXL-E 2.0 with center section cnc-machined from 6061 aluminum by ATOP. High grade all-metal ball joints at the pivot points provide zero backlash and strength. Dimensions: Hole to hole: 108mm Total length: 128mm Contents:2 pieces

€34.90*

Details

AT-DBXL 015 ATOP Lower front- and rear alloy a-arms for Losi Desert XL/XL-E / 2.0

Genuine ATOP spare/option part. CNC-machined 6061-T6 aluminum suspension arms for Losi DBXL. Set of four a-arms with plastic bushings for the hinge pins, all required nuts and bolts are included.Contents:2 pieces

€79.90*

Details

AT-DBXL034 ATOP Aluminum servo saver for Losi DBXL 2.0

Genuine ATOP spare/option part. Ballraced servo saver and steering assy, for Losi DBXL 2.0Replaces all plastic stock parts of the servo saver, no more tweaking even under high loads.Contents:1 piece

€99.90*

Customers also viewed

AT-DBXL016 ATOP aluminum steering rods for Losi DBXL-E 2.0

€34.90*

Details

AT-DBXL02 ATOP aluminum front top chassis brace for Losi DBXL 2.0

€39.90*

TT1025 Top Tuning BEAST Conversion kit for Losi Desert Buggy XL 2.0 / 12S

Genuine Top Tuning spare/option part. Beast Edition: Losi XL-E Standard equipment: Beast Edition: Motor: 780kV 520kV Regler: 160 Ampere 300 Ampere S-Leistung: 8S 12S 8S is not enough? You want to go to the limit? Then we have the right thing for you! With the Top Tuning conversion kit it is now possible to mount the ZTW Beast Pro Combo. With the torquey 620KV motor and the 12S 300A esc even the roughest off-road tracks are no problem anymore. The esc is fully programmable using the separately available programming card and can therefore be adapted to all track conditions. In addition, the supplied 15T pinion provides higher gearing and when driving with 12S, top speed is increased by approx. 20%.TT56112/520Top Tuning Monster Brushless Motor 520kV Max. amps: 129 A Max. voltage: 57 V Max. power: 7,350 W KV (RPM/Volt): 520 KV Mounting hole depth: 8 mm Bolt pattern: 4 x M4 at 30 mm pitch circle diameter Case diameter: 57.8 mm Case length: 112 mm Free shaft length: 30 mm Shaft diameter: 8 mm Weight: 1260 g Connector: 6.5 mm diameter Cable size: 8AWG y1549 ZTW Beast Pro 300A 12S ESCSpecification:Continuous Current: 300ABurst Current: 1800ABEC: 6,0 V/7,4 V einstellbar / 8 ABattery NIXX / LiPo: 18 - 36NC / 6-12S LiPoWidth: 74 mmLength: 115 mmHeight: 78 mmWeight: 500gProgrammable: JaWaterproof: splash-proofContents:1 piece

€599.90*

HT-Steel pinions for Carson / Smartech 2WD offroad cars

Genuine rc-car-online spare/option part. The pinions are made from nitrited steel. The do all correspond with the standard main gear and are secured using two grubscrews.These pinions are profile regraded and have all the same diameter!Module: m=1,5Profile regraded, this means that the number of teeth is changed while the diameter remained constant. The part of the involutes? curve that defines the tooth profile is changed. Positively regraded (lower number of teeth) pinions are stronger and run smoother, the reduced strength of negatively regraded pinions doesn?t really matter.Contents:1 piece

€29.90*

Configure now

AT-DBXL027 ATOP Aluminum C-hubs for all Losi DBXL/MTXL

Genuine ATOP spare/option part. CNC machined 6061-T6 aluminum C-hubs from ATOP to fit all Losi DBXL and MTXL versions, gas and brushless.Significantly more rigid than the stock plastic version, this part contributes to increased steering precision and directional stability. Plastic bushings for the hinge pins ensure reduced wear. Contents:2 pieces

€84.00*

AT-DBXL026/027 ATOP Aluminum front spindles for all Losi DBXL/MTXL

€149.90*

AT-DBXL013 ATOP Clutch bell carrier for Losi Desert XL+MTXL

Genuine ATOP spare/option part. CNC-machined 6061-T6 aluminum clutch bell holder for Losi DBXL+MTXL. Compared to the stock plastic part the higher strength of the aluminum part ensures secure seat for the bearings, increased dimensional stability at high temperatures and reduced operating temperatures for the bearings due the aluminums thermal conductivity. Larger bearings (12 x 28 x 7) for higher load capacity. Comes with ball bearings and spacer tubes included.It is recommended to use the ball bearings/bushings adhesive (y0113 Thread locking compound).Contents:1 set

€34.90*