Genuine TT spare/option part.The new and improved failsafe modul.This kill switch module works with most FM and 2.4 GHz rc-systems. Not compatible with AVC-equipped receivers! You must have a free channel on your rc-system in order to install the module! This means at least a 3-channel radio for standard 1-servo brake/throttle setups or a 4-channel radio for dual brake servos driven by the radio's mixer function. With this module you can stop the engine with your radio. Additionally the module features a failsafe function which stops the engine when the rx-battery's voltage drops below a certain level or the rc-system has a glitch. A kill switch module fulfils two tasks. On the one hand, as a safety device, it is intended to shut off an engine with magneto ignition in case of failure of the remote control, and on the other hand, the engine can be stopped at any time by remote control.While the latter is mainly used for convenience, the safety aspect is what really matters.The failsave circuit integrated in all modern remote controls may brake the vehicle in the event of a radio interference, but this feature is dependent on the basic functionality of the receiver system and its power supply. However, if the receiver, the gas servo or the power supply fails completely, the failsave of the remote control can no longer do its job. The vehicle may be running haywire at full throttle.In these cases, the kill switch will cut the ignition of the engine and the vehicle will roll out without power.Features:Ready to install no soldering requiredRemote LED for easy-to-spot operational status (ignition live/killed)Optically coupled to isolate the ignition from the radio systemThreshold value for undervoltage protection (4V, 5V, 6V) adjustable with jumpers allows adaptation to the rx-battery type (LiPo, LiFePo, NiMH, NiCd)Contents:1 piece

Genuine HT spare/option part. Protects the mated connection to prevent them from coming apart accidentally. Particularly recommended for direct power supply cords, as a tensile load on the cable can remove the link unnoticed and then you would perhaps think of a servo failure in the first place.The small size usually allows the installation even inside the receiver box.Also suitable for securing the connection of the receiver battery; the use of this clip means a big improvement in safety with little effort.Contents:1 piece

Genuine HT spare/option part. Extremely sturdy, fully padded transmitter bag! Fits all popular pistol grip transmitters Top quality; with padded adjustable length retaining straps to secure the transmitter, large zippered flap and adjustable carrying strap. Dimensions: Width: 23 cmHeight: 34 cmDepth: 17 cmContents:1 piece

Genuine HT spare/option part.Very strong linkage with M6 steel ball joints.M6 threaded rod with lock nuts, balls with holes for M4 screws.Maximum length about 96 mm, but through cutting the M6 rod allows for a minimum length of 48 mm.Significantly stronger than the standard plastic version, and especially recommend when using the Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP servo, this linkage can be used with "normal" servos as well.The threaded rod is not designed as a turnbuckle for a reason because there is not need to change the adjusted length for this application after installation. The setting accuracy of 0.5 mm (½ turn) means a maximum difference to the ideal length of 0.25 mm. This is always sufficient, the trim on the transmitter handles the final adjustment.On the other hand, a connecting rod with the same thread on both ends will always keep its setting when installed, even when both lock nuts are not tightened against the ball joints. Therefore reliability is higher.Set includes:2 x steel ball joints M62 x flat lock nuts1 x M6 x 60 mm threaded piece for Losi 5ive-T1 x M6 x 80 mm threaded piece for Losi 5ive-T 2.02 x spacer tubesContents:1 piece

Genuine Top Tuning spare/option part. Top Tuning The 20-amp Bigscale switch allows for a maximum input voltage of 30 volt. It is specifically designed as a receiver switch for use in combination with the Hitec HS-1005SGT servo and 4s receiver battery. The switch can also be used for other applications at your discretion with batteries up to 6S.Note: Top Tuning the electronic 20 amp Bigscale high voltage switch delivers the batterys full voltage. It does not replace a voltage regulator! The components which follow down the line (voltage regulator / servos / receiver) must be matched to this voltage! Using the latest MOSFET technology allows the 20 amp Bigscale high voltage switch to handle extreme loads, despite its small size. A blue LED status light clearly displays the activated mode. The 20 amp Bigscale high voltage switch is dust-and splash protected. He has an extremely low internal resistance and very low power consumption in off mode. Nevertheless it is recommended to unplug the battery when the model will not be used for an extended period. Properties:Voltage range: 3 to 30 VLoad: 20 ampsStandby consumption: 17 µAOperating temperature: - 15 ° C to +50 ° CCable length:Battery side 250 mmReceiver side 130 mmWeight: 13 gramsDimensions:Length: 29 mm Width: 13 mmHeight: 12 mmContents:1 piece

y0700 Double sided alloy servoarm: 9,90 EURy0700/01 Single-sided alloy servoarm: 7,90 EURy0701 Double sided split alloy servoarm: 14,90 EURy0701/01 Single-sided split alloy servoarm: 12,90 EURFor y0700, y0700/01, y0701 and y0701/01:Splitted Alloy servoarm for a more protecting screw connection (with a 2,0 mm allen head screw driver) causing stiffness on the servo output shaft Suitable for all servos with an output shaft with 25 teeth multi-tooth shaft, for example:y2006 Digital Big-Scale Servo D-21HVy2007 Digital large scale Brushless Servo CYS9130Nearly all Ribbe/Futaba servosMega Power servoThunder Tiger DS1015And many more!holes for linkage with M3 threadWhen you count the teeth of your servo you can check if this alloy arm will fit to your servo. Alloy servoarm are indispensable by strong digital servos, as used on big scale models for example, to optimize the servo forces being transferred.

Genuine ATOP spare/option part. CNC-machined from 6061 aluminum, significantly stronger and more rigid than any plastic version. Doule-sided anodized aluminum servo horn, available in 15T and 18t spline version. Three smooth 2.5 mm holes per side. 15T fits:Savöx 0236 MGSavöx 0235Losi 900and many other servos with 15T spline shaft18T fits:Spektrum DBXL-servo SPMS901Contents:1 piece

The Reflex Wheel Pro III is the perfect choice for sport-level car, truck and boat drivers. Everything you need to bash around your backyard or local track. Proven performance, reliability and range from the Spektrum brand make the Reflex Wheel Pro III great for someone looking to get involved in RC surface or a great grab-and-go transmitter for the expert. Key FeaturesPerfect for sport level cars and boatsErgonomic gripServo reversingProven reliability from the Spektrum brandReflex Wheel Pro III 3-channel receiver includedInterchangeable grips (Medium grip included. Other grip sizes sold separately in Optional Accessories)Travel adjustProduct SpecificationsNumber of Channels: 2Modulation: DSMRBand: 2.4GHzReceiver: Reflex Wheel Pro III Receiver Battery Type: AAThis set contains:Reflex Wheel Pro III Top Digital Big-Scale Steering ServoTop Digital Big-Scal  Throttle/brake servo y0425 Y-harness, universal connectorLOSB 9642 Global AC 6V Charger 2000 mAh 6V Battery with universal connectorWhen used in a FG 2WD car, adaptor plate 6118/02 is required for steering servo installation.

Genuine TopTuning spare/option part.Top quality lockable aluminum transmitter case in Futaba T7PX design. Case has plastic feet on bottom and back.The case lid features a lock on either side of the handle and a ribbed foam insert on the inside.Comes with 2 keys includedOuter dimensions: length approx. 320 mm Width: approx. 240 mm Height: approx. 160 mm Weight: 1.5 kgContents:1 piece

Genuine TopTuning spare/option part.Top quality lockable aluminum transmitter. Case has plastic feet on bottom and back.The full-surface foam inlay, divided into 15 mm blocks, allows the transmitter case to be individually adapted to each transmitter and its accessories.See example picture with Futaba transmitter!Of course, it is also possible to adapt the pre-cut foam inlay to other high-quality objects.The case lid features a lock on either side of the handle and a ribbed foam insert on the inside.Comes with 2 keys includedOuter dimensions: length approx. 320 mm Width: approx. 240 mm Height: approx. 160 mm Weight: 1.5 kgContents:1 piece

In case the servo cable is not long enough.Two selectable lengths:y0428/01 - 180 mmy0428/02 - 300 mm

Genuine ATOP spare/option part.CNC-machined from 6061-T6 aluminum by ATOP. CNC-machined 6061-T6 aluminum servo clamps from Area RC distribute the load from the mounting screws equally over the complete area of the mounting tabs, protecting them against breakage. Available in two versions:AT-5T020-01 - 0236 for stock servos in Losi 5ive and DBXL, Savöx 235 und 236, Orange Power and other servos with a mounting hole distance of 18 mmAT-5T020-02 - 5765 for MPX Rhino, Hitec 5765 and other servos with a mounting hole distance of 16 mmContents:2 pieces

Genuine ATOP spare/option part. CNC-machined from 6061 aluminum, significantly stronger and more rigid than any plastic version. Doule-sided anodized aluminum servo horn with 15T spline. Three M4 threaded holes per side. Fits:Savöx 0236 MGSavöx 0235Losi 900and many other servos with 15T / 8mm spline shaftContents:1 piece

Genuine ATOP spare/option part. CNC-machined from 6061 aluminum, significantly stronger and more rigid than any plastic version. Single-sided anodized aluminum servo horn, available in 18t spline version. Three M4 tapped holes for the linkage. 18T fits:Spektrum DBXL-servo SPMS901Contents:1 piece

Genuine HT spare/option part. This machined aluminum servo adapter allows easy installation of servos with a 69 x 18 mm mounting bolt pattern (for example Orange-Power, S8203) in vehicles / radio plates which provide a 75 x 18 mm mounting bolt pattern (for example Losi 5ive-T, Mini WRC, HPI Baja 5 series cars, many FG cars).The use of this adapter servo will neither tilt the servo, nor does it change installation height. Scope of delivery:1 x Servo mount adapter2 x Socket head cap screws 3 x 20 mm2 x Socket head cap screws 3 x 12 mm2 x Shim ring 3,2 mmContents:1 piece

Genuine Dynamite spare/option part.New Dynamite large scale servo arms are machined from high quality 7075 T6 aluminum material to withstand the high demand of giant scale RC surface applications.Fits servos with 8 mm / 15T shaft like i.e. Savöx 236, Losi S900S, Losi S 901, Spektrum 9010 and 9020.Features:Perfect fit every time CNC Machined for consistent and accurate tolerancesHigh Strength Made with 7075 T6 AluminumSecure connection Clamping styleGreat looks Red anodized aluminumContent:1 piece

Genuine ATOP spare/option part. Ballraced servo saver and steering assy, for Losi DBXL 2.0Replaces all plastic stock parts of the servo saver, no more tweaking even under high loads.Contents:1 piece

Genuine Spektrum spare/option part. Fits Spektrum DX3R Pro, DX3S and DX2S. Only working with a reciever with telemetry function like the "Spektrum SR3300T reciver".Content1 pieces

Genuine Area spare/option part.CNC-machined from 6061-T6 aluminum by Area RC. CNC-machined 6061-T6 aluminum servo clamps from Area RC distribute the load from the mounting screws equally over the complete area of the mounting tabs, protecting them against breakage. Available in two versions:0236 for stock servos in Losi 5ive and DBXL, Savöx 235 und 236, Orange Power and other servos with a mounting hole distance of 18 mm5765 für MPX Rhino, Hitec 5765 and other servos with a mounting hole distance of 16 mmContent:2 pieces

Product Specifications: Type: Digital Torque: 416.6 oz-in (30 kg-cm) @ 4.8V; 514.5 oz-in (37 kg-cm) @ 6V Speed: 0.19 sec/60 deg @ 4.8V; 0.14 sec/60 deg @ 6V Bushing Or Bearing: Bearing Bearing: Dual Connector Type: JR Gear Type: Metal Voltage: 4.8V to 6.0V Dimensions: Length: 2.59 in (65.8 mm) Width: 1.18 in (30.0 mm) Height: 2.26 in (57.4 mm) Weight: 5.40 oz (153.1 mm) Contents: Servo Single-sided servoarm 52mm 4 sided servoarm 60mm Servo disk 40mm diameter Mounting screws Rubber grommets Guide sleeves

Genuine Spektrum spare/option part. Only working with a reciever with telemetry function like the "Spektrum SR6000T reciver" or a transmitter with an external telemetry module. Works with all brushless motors for rpm data through SPM telemetry modules and integrated telemetry receivers. Easy installation.Content1 pieces

In case the battery cable is not long enough.Contents:1 piece

Genuine Dynamite spare/option part.New Dynamite large scale servo arms are machined from high quality 7075 T6 aluminum material to withstand the high demand of giant scale RC surface applications.Fits servos with 8 mm / 15T shaft like i.e. Savöx 236, Losi S900S, Losi S 901, Spektrum 9010 and 9020.Features:Perfect fit every time CNC Machined for consistent and accurate tolerancesHigh Strength Made with 7075 T6 AluminumSecure connection Clamping styleGreat looks Red anodized aluminumContent:1 piece

DYNB501 Dynamite Reaktion Lipo Receiver Pack 4000mAh 2S 7,4V 15C with EC3 and Universal electric wire.Specifications:Cells: 2SCapacity: 4000 mAhVoltage: 7.4 VLength: 105 mmWidth: 34 mmHeight: 27 mmWeight: approx. 190 gramsBalance connection: XPH (XH) Warning:- Use only under direct supervision of adults- Charge only in a suitable charging bag / protective bag- Do not store battery discharged (at least 50% charge is recommended)