F1465 Futaba edge protector - 1pce.
Product number:
sender_0007
EAN:
4058575009900
Product information "F1465 Futaba edge protector - 1pce."
Original part no. F1465
Fits 3-PDF and 3-PJ as well.
Fits 3-PDF and 3-PJ as well.
Login
Customers also bought
sender_0006 Color:
Green with wheel+ 5.2EUR
Fits 3-PDF and 3-PJ as well.
Variants from €9.20*
Similar products
Genuine HT spare/option part. Protects the mated connection to prevent them from coming apart accidentally. Particularly recommended for direct power supply cords, as a tensile load on the cable can remove the link unnoticed and then you would perhaps think of a servo failure in the first place.The small size usually allows the installation even inside the receiver box.Also suitable for securing the connection of the receiver battery; the use of this clip means a big improvement in safety with little effort.Contents:1 piece
Genuine HT spare/option part. Extremely sturdy, fully padded transmitter bag! Fits all popular pistol grip transmitters Top quality; with padded adjustable length retaining straps to secure the transmitter, large zippered flap and adjustable carrying strap. Dimensions: Width: 23 cmHeight: 34 cmDepth: 17 cmContents:1 piece
Genuine TopTuning spare/option part.Top quality lockable aluminum transmitter case in Futaba T7PX design. Case has plastic feet on bottom and back.The case lid features a lock on either side of the handle and a ribbed foam insert on the inside.Comes with 2 keys includedOuter dimensions: length approx. 320 mm Width: approx. 240 mm Height: approx. 160 mm Weight: 1.5 kgContents:1 piece
Genuine TopTuning spare/option part.Top quality lockable aluminum transmitter. Case has plastic feet on bottom and back.The full-surface foam inlay, divided into 15 mm blocks, allows the transmitter case to be individually adapted to each transmitter and its accessories.See example picture with Futaba transmitter!Of course, it is also possible to adapt the pre-cut foam inlay to other high-quality objects.The case lid features a lock on either side of the handle and a ribbed foam insert on the inside.Comes with 2 keys includedOuter dimensions: length approx. 320 mm Width: approx. 240 mm Height: approx. 160 mm Weight: 1.5 kgContents:1 piece
sender_0006 Color:
Green with wheel+ 5.2EUR
Fits 3-PDF and 3-PJ as well.
Variants from €9.20*
Customers also viewed
Genuine TopTuning spare/option part.Top quality lockable aluminum transmitter case in Futaba T7PX design. Case has plastic feet on bottom and back.The case lid features a lock on either side of the handle and a ribbed foam insert on the inside.Comes with 2 keys includedOuter dimensions: length approx. 320 mm Width: approx. 240 mm Height: approx. 160 mm Weight: 1.5 kgContents:1 piece
y1418 Color:
1418/05 - Yellow
Can be used as reinforcement for genuine HPI and Losi rims as well.Set includes:Two pieces of reinforced outside ringsTwo pieces of reinforced inside ringsand 40 pieces of 2.5 mm allen head screws (for 2 mm allen wrench)Colours:y1418/01 - Greyy1418/02 - Bluey1418/03 - Redy1418/04 - Orangey1418/05 - Yellow
Genuine FG spare/option part. The set includes: 10250/02 FG Body set F2000 1.5 mm 10254 FG Rear spoiler for F1 10455 Frontspoiler 10265/03 y0312 Decals Contents:1 set
Genuine Hitec spare/option part.Waterproof Power IP67 for large models and many industrial applicationsServo HS-1100WP is the most powerful and 100% waterproof servo Hitec large assortment! Thus, it is ideally suited for industrial applications and also for XXL large-scale models. Equipped with a hand-brush motor for maximum reliability and durability, and which protects from the full milled aluminum housing perfectly against electromagnetic interference. Another special course (not programmable) to call the virtually indestructible steel gears and a digital servo electronics IP67 classification.The Servo HITEC HS-1005SGT delivers maximum and constant performance and with its data also a favorite for industrial applications such as UAV, robotics and special effects. Technical data:Width: 33 mm Height: 73 mm Length: 64 mm Weight: 0340 kg Power Type: Mega Features: operating voltageFrom 11.1 to 14.8 volts, Amendment leads possible (Optional) Engine type servos: brushed Transmission: steel Operating voltage in V: 11.1 to 14.8 volts Actuating time s / 60 ° at 11.1 volts: 0:26 Setting time s / 60 ° at 14.8 volts: 12:19 Torque in kg cm at 6.0 volts: 84 Torque in kg cm at 7.4 volts: 110 Teeth: Mega Ball bearings: Yes, 2 times MR148 Waterproof: Yes Flight recommendation: YES Recommendation Heli: YES Recommendation Car: YES Recommendation boat: YES Temperature range: -20 ° to 60 ° CFeatures:Highest force Enormous holding power Indirect long-life potentiometer, 1 million cycles Steel gears Bearings, 2-MR148 Aluminum housing Separate signal and power supplyContents:1 piece
The SPEED TEC 7-port genuine Zenoah engine is optimized for performance by hand with sophisticated craftsmanship and guarantees, besides greatly increased performance, excellent workmanship and stamina. More power and torque through the three additional transfer ports.SPEED TEC V 7-port version modifications: Cylinder:Cylinder bottom modified for higher compressionenlarged and flow-optimized transfer portsmachining of three additional transfer ports raises number of ports from 4 to 7intake and exhaust ports optimized and matchedport timing modifiedCrankshaft:is adjusted, aligned and balancedFlywheel and ignition:Weight reduced and checked for run-out.Gaskets:Premium quality gaskets installed. Cylinder gasket installed using elastic gasket sealer.With the new "K & N" version of the Losi DBXL there is another detail, which need to be considered.From the very beginning the hole pattern for the engine installation in the DBXL chassis plate was no precise match to the hole pattern of the engine, even when delivered in stock form with standard engine. Now with the "K&N" version the engine mount has been changed to eliminate this discrepancy. However, all aluminum engine mounts available on the market share their dimensions with the previous plastic engine mount. For the installation of a G320 Zenoah in a "K&N" -DBXL two possible combinations exist in order to obtain the correct hole pattern:When using the standard (new) plastic engine mount a shortened clutch housing is required as in a 5ive-TWhen using an aluminum engine mount a stock length clutch housing is requiredSeparately, it is recommended to enlarge the cutout in the body panel in front of the K & N air filter for about 2 - 3 mm to ensure that the panel cannot chafe on the air filter.For all HPI Baja 5 cars the G320RCer clutch housing has to be shortened at the mounting base, for Losi 5ive- T and Desert Buggy XL cars the clutch housings overall length must be shortened to CY size.When installing the air filter you must pay attention to the length of the screws.For use on Losi and HPI we recommend M5x45 screws (like H94763); you can also cut existing screws to length, of course.When ordering with a modified clutch housing we will include these screws!In our shop you can select from Zenoah G320RC engines already modified to fit your HPI or Losi car.The installation of a Zenoah G320RC in a Smartech C5 onroad car is possible without modifications. However, due to the engines performance aluminum engine mounts (set # y0189) are mandatory!The installation of the Zenoah G320RC in other cars (like FG or Smartech buggies / monsters a.s.o.) is not even remotely straightforward, since the layshaft pinion (the small pinion in front of the big differential spur gear) is in the way for the larger Zenoah G320RC crankcase.Compatibility Zenoah / Losi 5ive-T:Please note that for installation in a Losi 5ive the fan cover must be swapped for a Losi or CY cover #5341 in order to fit the chassis" bolt pattern.If you want to install a Zenoah engine into the Losi 5ive, you usually have to use a fan cover from the CY engine.However, there is a workaround to maintain Zenoah fan cover.The adjustment is done via the pinion specific mounting plates for the engine. The change always affects only the rear, outer (carburetor side) plate under the fan cover. This is rotated by 180°; so that the embossed number on this plate faces the exhaust side of the engine!18T pinion: use 20T plate, rotated 180°19T pinion: use 19T plate, rotated 180°20T pinion: use 18T plate, rotated 180°On the plus side you gain the opportunity to easily mount a Zenoah engine keeping the original fan cover. On the other hand there will be the disadvantage of the necessity to combine two different sets of engine mounting plates when installing any pinion other than the stock 19T version. Therefore we do not recommend this workaround for everyday use. Nevertheless it works perfectly should ever the need arise. Attention! We recommend to run exclusively fully synthetic 2-stroke engine oil, like y0813 Motul 800 racing oil.
Genuine Losi spare/option part. The esc mounting bracket is equipped with an extremely strong double-sided adhesive tape for fixing the controller. Additionally the esc can be secured with the Top Tuning Velcro TT1021/12, which you can select from the shopping options.Compared to the standard plate, the support surface has been widened by 1mm, so that the ZTW 300A controller can be mounted ideally; slipping back and forth is securely avoided.Contents:1 set