Genuine HT spare/option part. Hardened special screws for mounting the beadlock rings of MadMax and Losi DBXL rims.For HPI rims due to the screw head diameter only to be used in combination with non-HPI beadlock rings (i.e. MadMax or Losi 5ive-T)!The combination of larger diameter and substantially larger thread depth ensures a secure grip of the screws in the plastic of the rims; the coarse thread also allows for quick assembly.The large head with T10 hexalobular drive distributes the load as wide as possible on the ring.The screws are galvanized for rust protection.Please note: it is not recommended to use the screws in rims which had previously M3 screws installed. With new rims or in exchange for M2.5 screws appropriate strength is ensured.Dimensions: Diameter: 3,1 mmLength: 12 mmHexalobular drive: T10 (Torx) Content:1 Set of 40 screws for one pair of rims.
Can be used as reinforcement for genuine HPI and Losi rims as well.Set includes:Two pieces of reinforced outside ringsTwo pieces of reinforced inside ringsand 40 pieces of 2.5 mm allen head screws (for 2 mm allen wrench)Colours:y1418/02 - Bluey1418/03 - Redy1418/05 - Yellow
The off-road tire for hard packed dirt and spectacular drifts!Gives great results on those carpets which are typical for some off-road tracks. 616 grippy square studs per tire, a total of more then 2.400 for a complete set of tires, guarantee maximum traction! The lower profile of the outer stud rows reduces lateral traction and guarantee exceptional directional stability and allows for spectacular drifts! Therefore the car is less prone to undesirable side rolls!The Narrow-Grip 616 tires are mounted on a flexible 10 spoke rim with steel ring reinforced 24 mm hex drive. 10 screws per beadlock ring keep the tires in place. The Narrow-Grip 616 tires feature a firm foam insert, making them suitable even for heavier weight cars.To prevent premature wheel drive wear the fit to the rim is very tight. Therefore the rim should be properly aligned with the hex drive and completely mounted via tightening the wheel nut! Attention: When using the Narrow-Grip wheels on a Super Losi Rock-Rey model, special wheel hexes are required. Also on FG and Carson models. For mounting on a Traxxas X-MAXX you need a set of special Top-Tuning wheel nuts. - TT1040 Top Tuning wheel hub 24mm/6-edge for Losi Super BajaRey/2.0 and Super Rock Rey for plastic axle stubs. - AT-004 Atop wheel nuts 4 pieces Dimensions:Outer tire diameter: 180 mmTire and rim width: 60 mmRim inner diameter: 120 mmWeight for one tire: 430 grams / for a pair: 860 grams24 mm hex for Losi 5IVE-T, HPI Baja 5, MCD Wheels drives:24 mm hex for Losi 5IVE-T, HPI Baja 5 and MCD ccars.
For sealing the axles on Losi 5ive-T and Mini cars, keeps debris out of the inner screws which secure the retainer pin. Set of 4 or set of 10 to choice.Can be used for Losi 5ive-T, Mini and HPI Baja cars.
Medium firmness molded tire inserts with shaped shoulders and recesses to match the beadlock fittings.The medium shore hardness compound of the colored top quality tire inserts provides optimal support for the tire's shoulder and allows for perfect rolling characteristics of the tire. The perfect tire insert for the MadMax tires with 170 / 190 mm tire diameter is available in two widths.Fits 10-spoke GPM-racing aluminum rims (Losi / HPI). Applications:for 60 mm tire width: # y1321/01for 80 mm tire width: # y1321/02for GIANT-GRIP #y1321/06
Off-road tires for sandy underground! Gives great results on those carpets which are typical for some off-road tracks. 462 grippy square studs per tire, a total of more then 1800 for a complete set of tires, guarantee maximum traction! The lower profile of the outer stud rows reduces lateral traction and guarantee exceptional directional stability! Therefore the car is less prone to undesirable side rolls! The rim is the 6-spoke design with a steel reinforcement ring around the wheel drive. The NARROW-GRIP tires are available with 24mm hex for Losi, HPI Baja 5 and Carson GP Wild Attack series cars and they allready glued!To prevent premature wheel drive wear the fit to the rim is very tight. Therefore the rim should be properly aligned with hex drive and completely mounted via tightening the wheel nut! Dimensions:Outer tire diameter: 175 mmTire and rim width: 62 mmRim inner diameter: 119 mmWeight for one tire: 375 grams / for a pair: 750 gramshe manufacturer of the Narrow-Grip 462 indicates that the use of these tires on very heavy models, like the Losi 5ive-T under heavy conditions, such as jumps and shifting / tilting of the chassis, may lead to breakage of spokes or hex socket. Due to this notice that kind of failure will not be compensated. We apologize for this note!As an alternative, we recommend our special offer for the Losi 5ive-T OEM tires and in particular all tire combinations with MadMax EXTREME rims or for Losi and HPI models: y1406/01 - Big Digger y1407/01 - Cross Bond y1408/01- Over Lander y1409/01 - Giant Grip y1417/01 - Ultra Grip Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (24 mm hex for Losi and HPI Baja 5 Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable. Wheels drives:18 mm square for FG & co.24 mm hex for Losi, HPI Baja 5 cars.Contents:2 pieces / 1 pair
The off-road tire for hard packed dirt and spectacular drifts!Gives great results on those carpets which are typical for some off-road tracks. 616 grippy square studs per tire, a total of more then 2.400 for a complete set of tires, guarantee maximum traction! The lower profile of the outer stud rows reduces lateral traction and guarantee exceptional directional stability and allows for spectacular drifts! Therefore the car is less prone to undesirable side rolls!The Narrow-Grip 616 tires are mounted on a flexible 10 spoke rim with steel ring reinforced 24 mm hex drive. 10 screws per beadlock ring keep the tires in place. The Narrow-Grip 616 tires feature a firm foam insert, making them suitable even for heavier weight cars.To prevent premature wheel drive wear the fit to the rim is very tight. Therefore the rim should be properly aligned with the hex drive and completely mounted via tightening the wheel nut! Attention: When using the Narrow-Grip wheels on a Super Losi Rock-Rey model, special wheel hexes are required. Also on FG and Carson models. For mounting on a Traxxas X-MAXX you need a set of special Top-Tuning wheel nuts. - TT1040 Top Tuning wheel hub 24mm/6-edge for Losi Super BajaRey/2.0 and Super Rock Rey for plastic axle stubs. - AT-004 Atop wheel nuts 4 pieces Dimensions:Outer tire diameter: 180 mmTire and rim width: 60 mmRim inner diameter: 120 mmWeight for one tire: 430 grams / for a pair: 860 grams24 mm hex for Losi 5IVE-T, HPI Baja 5, MCD Wheels drives:24 mm hex for Losi 5IVE-T, HPI Baja 5 and MCD ccars.
Genuine HPI spare/option part. Standard front Baja inner foam. Fit´s for Baja 5B RTR, Baja 5B SS.Content:2 pieces/1 pair
The Tarmac Buster tires are the ticket for asphalt, concrete, or even hard packed clay. Molded in HPI?s exclusive M Compound, the Tarmac Busters have an aggressive street tread pattern that delivers outstanding grip on the street. Sold in pairs, these tires are a direct replacement for the factory Baja 5B tires. You need the same tire insert as for the stock tires. The inserts are includet.Durchmesser x Breite / diameter x width 170 x 60 mm
Medium firmness molded tire inserts with shaped shoulders and recesses to match the beadlock fittings.The medium shore hardness compound of the green colored top quality tire inserts provides optimal support for the tire's shoulder and allows for perfect rolling characteristics of the tire. The perfect tire insert for the HPI-Baja 5B series with 170 mm tire diameter is available in two widths.Fits 10-spoke GPM-racing aluminum rims (Losi / HPI) and MadMax rims as well. Applications:for 60 mm tire width: # y1323/01for 80 mm tire width: # y1323/02
Genuine HPI spare/option part. Content:2 piece / 1 pair
Genuine HPI spare/option part. Baja 5T/Rear - Losi 5ive-T Sand Buster-T Rib front and Sand Buster-T Paddle rear tires are now available from HPI Racing. These tires are designed specifically for the Baja 5T truck.Sand Busters-T Rib fronts have a rib down the center of the tire to cut through the sand for stable steering, and the Sand Buster-T Paddle rears have 10 large paddles for maximum traction in sand and soft dirt. Sand Buster's are designed for the sand, but you can also run them in loose dirt and even in the mud!Suitable for Losi 5ive-T as well (paddles all around).Contents:2 pieces / 1 pair
Genuine HT spare/option part. Hardened pins made of 100Cr6 steel for driveshafts, differentials, wheel drives and similar applications. Pack of ten. Sizes available:y1345/01: 4 x 18 mm, e.g. for Losi 5ive-T/Mini and HPI Baja differentials or HPI Baja layshafty1345/02: 4 x 20 mm, e.g. for Losi 5ive-T/Mini CVD jointsy1345/03: 4 x 24 mm, e.g. for Losi DBXL and HPI Baja wheel hexy1345/04: 5 x 24 mm, e.g. for Losi 5ive-T/Mini wheel hexContents:10 pieces
The Tarmac Buster tires are the ticket for asphalt, concrete, or even hard packed clay. Molded in HPI?s exclusive M Compound, the Tarmac Busters have an aggressive street tread pattern that delivers outstanding grip on the street. Sold in pairs, these tires are a direct replacement for the factory Baja 5B tires. You need the same tire insert as for the stock tires.
Genuine GPM spare/option part.Tires for a solid to medium terrain.Contents:2 pieces
Genuine HPI spare/option part.The Dirt Buster rear Block tyre in S Compound is the perfect all-terrain pattern and compound for the Baja 5B! It fits easily on the multipiece rear wheels and provides the excellent grip and traction needed to roll over any type of surface you might encounter. Dozens of square-shaped pins grab dirt and grass to propel the Baja through all terrains. The low-profile sidewalls resist flex, giving you more traction in turns than a high-profile tyre would. This is the perfect off-road tyre for the Baja!Dimensions:Diameter: 170 mmWidth: 80 mmContent:2 pieces / 1 pair
Genuine HPI spare/option part. Complete mounted on black rims with tire inserts.Dimensions:Diameter: 170 mmWidth: 60 mmContent:2 pieces / 1 pair
Genuine HPI spare/ption part.For HPI Baja 5BThe Hot Bodies off-road tyre range has expanded to fit the 1/5th scale Baja 5B from HPI!Now available for the Baja buggy are the awesome Double Blade 2WD front tyres, as well as the Proto and Khaos rear tyres!Use HB Baja tyres to put the hurt on the opposition!White compound is medium, great for practice and all-around use.Blue compound is firm for high-bite tracks.Contents:2 tires
Genuine GPM spare/option part.Tires for a solid to medium terrain.Diameter x width: 170 x 80 mmContents:2 pieces
Medium firmness molded tire inserts with shaped shoulders and recesses to match the beadlock fittings.The medium shore hardness compound of the green colored top quality tire inserts provides optimal support for the tire's shoulder and allows for perfect rolling characteristics of the tire. The perfect tire insert for the HPI-Baja 5B series with 170 mm tire diameter is available in two widths.Replacement part for MadMax Multi Pin and Giant Grip tires.
Medium firmness molded tire inserts with shaped shoulders and recesses to match the beadlock fittings.The medium shore hardness compound of the red colored top quality tire inserts provides optimal support for the tire's shoulder and allows for perfect rolling characteristics of the tire. The perfect tire insert for the HPI-Baja 5B series with 190 mm tire diameter is available in 60 mm.Fits 10-spoke GPM-racing aluminum rims (Losi / HPI) and MadMax rims as well.Content:2 pieces/1 pair
Product Safety DangerCauses skin irritation.Contains (R)-P-MENTHA-1,8-DIENE. May produce an allergic reaction.Contains Geranyl acetate. May produce an allergic reaction.Contains NERYL ACETATE. May produce an allergic reaction.Contains citral. May produce an allergic reaction.Contains linalool. May produce an allergic reaction.Extremely flammable aerosol.May cause drowsiness or dizziness.Pressurised container: May burst if heated.Toxic to aquatic life with long lasting effects.Genuine HPI spare/option part. The Dirt Buster front Rib tyre in M Compound is the ideal match for the Block rear tyres. With multiple rows of ribs ably guiding the tyres, you are able to control the Baja 5B in nearly any off-road situation and on nearly any surface! Side grip is enhanced by the 'dash' ribs, allowing the tyres to grip surfaces like mud and grass. The solid ribs grip harder surfaces like hardpacked dirt and clay, and also work great on very loose surfaces like sand. This is the perfect off-road tyre for the Baja!Content:2 pieces / 1 pair
Genuine HPI spare/option part. For HPI Baja 5SC, fits too for HPI Baja 5B, 5B 2.0 and 5T(GUNMETAL/2pcs) These 24mm HD front hex hubs replace the stock hubs on HPI Baja 5B and 5T vehicles for extra durability. First introduced on the Baja 5SC truck, these heavy duty front hubs use a screw & nut design that eliminates the previous use of an e-clip. They're precision machined from billet aluminum for a perfect fit and gunmetal anodized for custom looks.Color: gunmetal.Contents:2 pieces
Off-road tires for sandy underground! Gives great results on those carpets which are typical for some off-road tracks. 462 grippy square studs per tire, a total of more then 1800 for a complete set of tires, guarantee maximum traction! The lower profile of the outer stud rows reduces lateral traction and guarantee exceptional directional stability! Therefore the car is less prone to undesirable side rolls! The rim is the 6-spoke design with a steel reinforcement ring around the wheel drive. The NARROW-GRIP tires are available with either 18 mm square drive to fit FG & co. To prevent premature wheel drive wear the fit to the rim is very tight. Therefore the rim should be properly aligned with the square or hex drive and completely mounted via tightening the wheel nut! Dimensions:Outer tire diameter: 175 mmTire and rim width: 62 mmRim inner diameter: 119 mmWeight for one tire: 375 grams / for a pair: 750 gramshe manufacturer of the Narrow-Grip 462 indicates that the use of these tires on very heavy models, like the Losi 5ive-T under heavy conditions, such as jumps and shifting / tilting of the chassis, may lead to breakage of spokes or hex socket. Due to this notice that kind of failure will not be compensated. We apologize for this note!As an alternative, we recommend our special offer for the Losi 5ive-T OEM tires and in particular all tire combinations with MadMax EXTREME rims for FG, Smartech and Co.:y1400/01 - Tarmac Bustery1401/01 - Big Digger y1402/01 - Cross Bond y1403/01 - Over Lander y1404/01 - Giant Grip y1416/01 - Ultra Grip Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (18 mm square for FG Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable. Wheels drives:18 mm square for FG & co.Contents:2 pieces / 1 pair