Skip to main content Skip to search Skip to main navigation
EXTRA 20% off Outlet*. Use Code: EXTRA20 at checkout!!
+49 2151 820200 Mon-Fri 9 am - 6 pm, Sa 9 am - 1 pm

4736 HPI Dirt Buster rib front tyre Medium

Product information "4736 HPI Dirt Buster rib front tyre Medium"

Genuine HPI spare/option part. 

Complete mounted on black rims with tire inserts.

Dimensions:
  • Diameter: 170 mm
  • Width: 60 mm


Content:
  • 2 pieces / 1 pair

0 of 0 reviews

Average rating of 0 out of 5 stars

Leave a review!

Share your experiences with other customers.


Accessories / Spare parts

Average rating of 0 out of 5 stars

y0521 Madmax/HPI-rim to FG-car wheel adaptor
Genuine HT spare/option part.This adaptor allows you to install all MadMax/HPI tire/rim combinations on FG, Carso, Smartech 2WD/4WD and other cars with the same wheel shaft configuration. Losi 5ive tires can be used as well, but they hey have to be mounted on MadMax/HPI rims because Losi rims are too thick at the center. The adapter is drilled for 8 mm wheel shafts (FG, Smartech/Carson and many more!), hex size of wheel drive and wheel nut is 24 mm hex with M18x1.0 thread (same as HPI).Please note:FG wheel shafts come with either M6 or M8 thread size. It can even happen that a vehicle has different thread sizes front and rear! Therefore, please make sure which version is required before placing an order.Converting your car takes only a couple of minutes with this easy to install adaptor. just see picture "installation instruction" for a schematic installation.Contents:2 pieces

€39.90*

Alternatives

Average rating of 0 out of 5 stars

B501 Carson Dirt Tire front for Wild GP Attack
Genuine Carson spare/option part. Contents:2 pieces / 1 pair

€69.90*

Average rating of 0 out of 5 stars

y1416/01 GPM - Ultragrip 170x80/x60 mm Wheels for FG, Smartech und Co. (18 mm square wheel drive)
Ultragrip 170x80 and 170x60 on black MadMax Extreme rims with 20 beadlock screws, with 18 mm square socket and reinforced silver headlock rings for FG, Smartech and many more. 150 shifted long lugs and a central, 4 mm high ridge on the 60 mm wide front tire, and 210 pieces of square 6 x 4 mm studs on the 80 mm wide rear tire ensure optimal propulsion! The flattened profile structure of the rows of knobs reduces the directional control and guarantees an exceptionally good on-center feel! This makes the car less prone to unwanted traction rolls! Due to the extreme load created by the MadMax Ultragrip tires the rim was optimized again with a reinforcement ring.The tires are fitted with a special rigid insert, which can handle the cornering forces and maintain the tires shape even on heavy cars. The GPM Ultragrip are designed for use on sandy surfaces.We recommend to check the beadlock screws after the run. Dimensions:Outer diameter: 170 mmFront tire width: 60 mmRear tire width: 80 mmReinforced 18 mm square wheel drive Regular price EUR 177,40The video shows the 18 mm square drive version. Also available with 24 mm hex. Some off-road tires knowledge can be found here!

€99.90*

Average rating of 0 out of 5 stars

y1407/01 MadMax CROSS BOND 170x80/x60 tires for HPI + Losi (24 mm hex drive)
CROSS BOND 170 x 80 mm and 170 x 60 mm tires with black MadMax Extreme 20 bolt-beadlock rims with 24 mm hex drive and reinforced beadlock rings were designed for use on loose surfaces. The extremely rigid and differently structured lugs of the CROSS BOND ensure optimum power transmission and also allow for excellent grip on loose surfaces, such as sand and soil. The lugs are raised at the treads outside, and therefore provide maximum grip, particularly when cornering where the tire is canted to the outside. Due to the extreme load created by the MadMax CROSS BOND tires the rim was optimized again with a reinforcement ring.The tires are fitted with a special rigid insert, which can handle the cornering forces and maintain the tires shape even on heavy cars. We recommend to check the beadlock screws after the run. Dimensions:Outer diameter: 170 mmFront tire width: 60 mmRear tire width: 80 mmReinforced 24 mm hex driveThe video shows the 18 mm square drive version. Also available with 24 mm hex. Some off-road tires knowledge can be found here!

€119.90*

Average rating of 0 out of 5 stars

y1409/01 GIANT GRIP tires on MadMax Extreme rims for Losi and HPI, pair
GIANT GRIP 190 x 70 with black colored MadMax Extreme rims, 20-fold screwed, very tough, with 24 mm hex drive and reinforced orange beadlock rings for Losi 5ive-T and Desert-Buggy XL as well as all HPI Baja 5 B/T cars.The GIANT GRIP provides giant traction through 96 about one cm² wide and 5 mm high strong lugs, getting ample grip even on loose surfaces like sand and soil.Due to the extreme strain caused by the GIANT GRIP tires the MadMax rim with reinforcement ring had to be optimized once more.The GIANT GRIP tires come with strong special tire inserts which allow to transfer the power without canting, even on heavy cars like the Losi 5ive-T.Dimensions:Outer diameter: 190 mmTire width at bead 70 mmTread width 80 mmReinforced 24 mm hex wheel driveThe MadMax Giant Grip tires use 60 mm wide rims ( y1415/01 or y0761/01).The video shows the 18 mm square drive version. Also available with 24 mm hex. Some off-road tires knowledge can be found here!

From €64.90*

Average rating of 0 out of 5 stars

y1406/01 MadMax BIG DIGGER 170x80/x60 for HPI + Losi (24 mm hex drive)
BIG DIGGER 170x80 and 170x60 with black MadMax Extreme rims with 20 beadlock screws, with 24 mm hex socket and reinforced orange beadlock rings for Losi 5ive-T and Desert Buggy XL as well as all HPI Baja 5 cars.The MadMax tires had 84 extremely strong tread blocks on the front tires and 96 on the rears, with more than 1 cm² cross-section and 6 mm tread depth, allow for best power transfer and provide excellent grip even on loose surfaces like sand or soil. Due to the extreme load created by the MadMax BIG DIGGER tires the rim was optimized again with a reinforcement ring.The tires are fitted with a special rigid insert, which can handle the cornering forces and maintain the tires shape even on heavy cars like the Losi 5ive-T.We recommend to check the beadlock screws after the run. Dimensions:Outside diameter: 170 mmFront tire width: 60 mmRear tire width: 80 mmReinforced 24 mm hex wheel drive The video shows the 18 mm square drive version. Also available with 24 mm hex. Some off-road tires knowledge can be found here!

€119.90*

Similar products

Average rating of 0 out of 5 stars

75106 HPI Body clips 6 mm, black
Genuine HPI spare/option part. Fits a huge range of RC cars and trucks, and conveniently packaged in packs of 20 for quick replacement. Cool black colour to match every paint scheme.Content:20 piece

€4.49*

Average rating of 0 out of 5 stars

75071 HPI O-rings S15 Baja SS
Genuine HPI spare/option part. Color: orange.Dimensions: 15 x 1,5 mm.Content:8 pieces

€8.78*

Average rating of 0 out of 5 stars

4837 HPI Tarmac Buster front tire, M COMPOUND (170X60MM/2PCS)
The Tarmac Buster tires are the ticket for asphalt, concrete, or even hard packed clay. Molded in HPI?s exclusive M Compound, the Tarmac Busters have an aggressive street tread pattern that delivers outstanding grip on the street. Sold in pairs, these tires are a direct replacement for the factory Baja 5B tires. You need the same tire insert as for the stock tires. The inserts are includet.Durchmesser x Breite / diameter x width 170 x 60 mm

€38.39*

Average rating of 0 out of 5 stars

H4840 Tarmac Buster rear tire, M COMPOUND (170X80MM/2PCS)
The Tarmac Buster tires are the ticket for asphalt, concrete, or even hard packed clay. Molded in HPI?s exclusive M Compound, the Tarmac Busters have an aggressive street tread pattern that delivers outstanding grip on the street. Sold in pairs, these tires are a direct replacement for the factory Baja 5B tires. You need the same tire insert as for the stock tires.

€34.90*

Average rating of 0 out of 5 stars

H75072, O-RING P20 (20X2.5MM/BLACK/8PCS)
O-ring for shock spring tension adjustment nut. Fits HPI and GPM Baja shocks.

€6.90*

Average rating of 0 out of 5 stars

2018/01 HPI Receiver battery pack "Hump" 6V / 4500 mAh Ni-MH
Fits all HPI 1/5 scale cars. With BEC connector.

€54.10*

Average rating of 0 out of 5 stars

67972 HPI HB Khaos tires white/white for Baja 5B rear, 2 pcs.
For HPI Baja 5BDimensions: Outer diameter: 170 mm Rear tire width: 80 mmThe Hot Bodies off-road tyre range has expanded to fit the 1/5th scale Baja 5B from HPI!Now available for the Baja buggy are the awesome Double Blade 2WD front tyres, as well as the Proto and Khaos rear tyres!Use HB Baja tyres to put the hurt on the opposition!White compound is medium, great for practice and all-around use.Blue compound is firm for high-bite tracks.

€52.90*

Average rating of 0 out of 5 stars

3227 HPI Super star wheel, Gunmetal 120 x 75 mm
Genuine HPI spare/option part. Special 3-piece bead lock wheels for the Baja 5B. A beadlock ring (not included) is bolted onto the wheel to securely hold the tyre in place. No glue is used to mount the tyres, which makes changing the tyres a simple task! Also, the wheels can be used again with new tyres.Made from tough, high-impact nylon for extra toughness, the popular HPI Super Star design is available in a wide variety of colours, with the opportunity to further customize the colour scheme further with a variety of bead lock rings! All wheels and bead lock rings are sold to fit front or rear pairs of tyres.Content:2 pieces / 1 pair

€28.90*

Average rating of 0 out of 5 stars

85249 HPI Rear wing set
Genuine HPI spare/option part. Baja 5T owners can now add a custom look to their truck with rear spoilers. These spoilers add downforce for stability at high speeds and the truck launch at the correct angle of attack on jumps. They're made from high impact nylon for extra durability.A decal sheet with HPI logos is included, along with the necessary mounting hardware. Choose the color that complements your paint job and accessories!Content:1 piece

€19.90*

Average rating of 0 out of 5 stars

3221 HPI Super star wheel, black, 120 x 60 mm
Genuine HPI spare/option part. Special 3-piece bead lock wheels for the Baja 5B. A beadlock ring (not included) is bolted onto the wheel to securely hold the tyre in place. No glue is used to mount the tyres, which makes changing the tyres a simple task! Also, the wheels can be used again with new tyres.Made from tough, high-impact nylon for extra toughness, the popular HPI Super Star design is available in a wide variety of colours, with the opportunity to further customize the colour scheme further with a variety of bead lock rings! All wheels and bead lock rings are sold to fit front or rear pairs of tyres.Content:2 pieces / 1 pair

€21.90*

Average rating of 0 out of 5 stars

67969 HPI HB Proto tires white/soft for Baja 5B rear
Genuine HPI spare/ption part.For HPI Baja 5BThe Hot Bodies off-road tyre range has expanded to fit the 1/5th scale Baja 5B from HPI!Now available for the Baja buggy are the awesome Double Blade 2WD front tyres, as well as the Proto and Khaos rear tyres!Use HB Baja tyres to put the hurt on the opposition!White compound is medium, great for practice and all-around use.Blue compound is firm for high-bite tracks.Contents:2 tires

€51.70*

Average rating of 0 out of 5 stars

4834 HPI Dirt Buster Block tyres rear, soft 170 x 80 mm
Genuine HPI spare/option part.The Dirt Buster rear Block tyre in S Compound is the perfect all-terrain pattern and compound for the Baja 5B! It fits easily on the multipiece rear wheels and provides the excellent grip and traction needed to roll over any type of surface you might encounter. Dozens of square-shaped pins grab dirt and grass to propel the Baja through all terrains. The low-profile sidewalls resist flex, giving you more traction in turns than a high-profile tyre would. This is the perfect off-road tyre for the Baja!Dimensions:Diameter: 170 mmWidth: 80 mmContent:2 pieces / 1 pair

€38.39*

Customers also viewed

%

Average rating of 0 out of 5 stars

MadMax SUPER GRIP Soft 170x80/x60 for FG, Smartech, HPI, Losi, Arrma & Co.
SUPER GRIP 170 x 80 mm and 170 x 60 mm with black MadMax Extreme rims for 18 mm square or 24 mm hex wheel drive, 20 beadlock screws per rim and reinforced orange beadlock rings. Fits FG, Smartech, Losi 5ive-T, 5ive Mini, Desert Buggy XL and all HPI Baja 5B and 5T/SC cars.Due to the extreme stress created by the MadMax SUPER GRIP tires, the rim has been optimized again.The tires come with a special rigid insert which transfers the applied forces without tilting; even with the heaviest cars like the Losi 5ive-T.All together, the SUPER GRIP lives up to its name and provides maximum grip, which makes it necessary to use the supplied 3 mm beadlock screws for the MadMax EXTREME rims instead of the usual 2.5 mm screws. Additionally, the seating of these screws should be checked after each use.The MadMax SUPERGRIP tires have been designed especially for use on tarmac. Even on fine-pored tarmac your car will still find enough grip! (As you can see in our video.) On most 1/5 and 1/6 cars the best combination is the use of 60 mm wide front and 80 mm wide rear tires. The Losi 5ive-T and Super Baja Rey should run 60 mm wide MadMax SUPERGRIP tires all around, because the 80 mm wide SUPERGRIP tires are a bit too wide for the body shell.The 80 mm wide MadMax tires are reinforced on the inside of the carcass with a special cross pattern in the tread section and ribs in the outside shoulder.The MadMax SUPERGRIP has a special on-road tread. These tires have excellent grip even after eating up the tread and can be used after that for a long time as slicks!MadMax SUPERGRIP spare rubber can be found here: MadMax SUPER GRIP spare part Some off-road tires knowledge can be found here!

€109.90* €129.90* (15.4% saved)

Average rating of 0 out of 5 stars

y1017 MadMax MAXI PIN tires complete set for Traxxas X-MAXX 4x4 with adapter
Offerset:2 Pairs MadMax Maxi Pin tires2 Pairs MadMax rims2 Pairs MadMax inlays2 Pairs / 4 pieces adapter TT1020/01MAXI PIN 185 x 75 with black colored MadMax Extreme rims, 20-fold screwed, very tough, with 24 mm hex drive and with reinforced orange beadlock rings for Losi and HPI. The MadMax MAXI PIN tires come with strong special tire inserts which allow transferring the power without canting, even on heavy cars. MadMax MAXI PIN tire was developed specifically for astro turf tracks! The special tread design with 480 studs per tire provides excellent grip, but also a high load on tire and rim! To stabilize the tire, the outer shoulder features radial ribs which minimizes the tilting under load and counteract the shear forces during cornering. Furthermore, the MAXI PIN tire has studs positioned on the outside shoulder, which support the steering in corners. All together the MAXI PIN tires provide maximum grip, which made it necessary to upgrade the beadlock screws on these MadMax EXTREME wheels. So they come with 3.0 mm screws instead of the usual 2.5 mm ones! Nevertheless, tires and beadlocks should be checked after every run.The set consists of four tires, including tire inserts and MadMax EXTREME rims and 4 pieces adapter wheel nuts TT1020/01. Dimensions: Outer diameter: 185 mm tire width at bead: 70 mm Tread width: 75 mm Reinforced 24 mm hex wheel drive The video shows the 18 mm square drive version. Also available with 24 mm hex. Some off-road tires knowledge can be found here!TT1020 Top Tuning Adapter wheel nutGenuine TopTuning spare/option part.These adapter nuts, manufactured from billet 7075 aluminum allow for easy and precise installation of all MadMax, HPI and Losi tires and rims on the Traxxas X-Maxx. For the best result possible, nut and adapter are manufactured as a one-piece unit.It should be noted that the wide rims can be used on the rear axle only. On the front axle they would limit the steering angle by grinding on lower a-arm and steering rod.Traxxas has microencapsulated the wheel shafts of the X-Maxx to secure the wheel nuts. Like any thread locking compound this is not for eternity. After several tire changes the use of a normal screw locking compound is advised, we recommend it "y0113 / 01 medium strength".The dimensions of the nut are specifically designed for use with MadMax, current HPI and Losi rims. Rims from Losi 5ive have slightly different dimensions in the hub area. This is meaningless on the large LOSI or HPI wheel adapters. With the smaller and shorter wheel nut thread of the X-Maxx wheel shafts you cannot compromise. Therefore there are also special nuts for the Losi rims/wheels available at our options menu.However, somewhere in the past, the injection moulds for the HPI rims were slightly modified in the hub area. As part of that job the bore diameter has probably been slightly increased. Therefore, the use of older rims in combination with the adapter nuts makes it necessary to increase the rim bore a little bit.Due to repeated requests for use: these wheel nuts replace the stock wheel nuts when installing the wheels!Contents:4 pieces

From €119.90*
%

Average rating of 0 out of 5 stars

y3300/2.0 Original Losi 5ive-T 2.0 tires with rims and inlays
Genuine Losi 5ive-T 2.0 spare/option part.Some of our customers order their Losi 5ive-T 2.0 with with optional MadMax rims and tires. Therefore we currently have an excess stock of genuine Losi 5ive-T 2.0 tire sets, that we can offer you at an extremely low price Complete mounted and original Losi 5ive-T 2.0 tires.Consists of parts from the following genuine Losi 5ive-T 2.0 sets: LOS45022 Losi Wheel & Beadlock Set, Grey, 5ive-T 2.0 LOS45023 Losi Tire Set, Firm, 5ive-T 2.0 LOSB7241 Tire Inserts front/rear, Soft One pair (two pieces) of complete OEM wheels, as it comes with the Losi 5ive-T 2.0; one each l/h and r/h version. In our shopping selection 2 pairs at a special price! Regular price for this set: 143,95 for two piecesDimensions:Width: 70 mmDiameter: 180 mm24 mm reinforced Wheel hex (Losi and HPI and other)Contents:2 pieces / 1 pair

From €99.90* €143.95* (30.6% saved)

Average rating of 0 out of 5 stars

160324 HPI Baja 5B SBK Flux build kit Electric
BUILD YOUR OWN ORIGINAL,AUTHENTIC HPI BAJA 5BHPI large scale fans, we have heard you! The one and only original HPI Baja 5B is BACK and ready for you to build from the ground up! The HPI SBK collection of Self Build Kits grows with the addition of not just one, but TWO 1/5th scale HPI kits! Fans of large scale off-road RC will be super excited to build their own gas-powered 1/5th scale Buggy with the HPI Baja 5B Self Build Kit!When the HPI Baja 5B buggy was first introduced, large scale RC was very expensive and quite difficult for the average RC hobbyist to experience. Using highly durable parts and innovative design features, HPI brought large scale off-road to new enthusiasts and ushered in a new, BIGGER era of RC!Now, YOU can build and own the legend! Experience the thrill and excitement of building a car which ends up being over 80cm (nearly 32 inches) long and weighing nearly 10kg (over 21 lb)! Just install your own engine and electronics as you build the HPI Baja 5B and you'll be ready for any adventure that comes your way!With extra-tough drivetrain parts like the viscous torque differential, super-durable composite spur gear with internal damping and all-metal drivetrain, the HPI Baja 5B is ready for your 23-32cc 2-stroke engine so you can experience the joy of gas-powered RC and up to 30-minute runtimes!The HPI Baja 5B is also equipped with extra-big and super-tough suspension parts, featuring awesome HPI durability! With its expertly designed molded composite suspension plus extra-long adjustable HD shocks, and massive high impact nylon 3-piece beadlock wheels, the Baja 5B is ready for full-speed racing on any off-road circuit!The 4mm thick 6061 aluminum monocoque chassis gives the HPI Baja 5B the classic desert racing buggy look. Precisely bent into shape for maximum strength, the chassis provides the mounting points for the engine and suspension, forming the backbone of the car. Precise steering is provided by a dual-bellcrank rack and cam-type servo saver. Aluminum parts are anodized in cool gunmetal and the classic Baja desert racer clear polycarbonate body is included in the SBK kit, ready for your custom racing scheme!The Baja 5B SBK is a great addition to your HPI collection, as well as a fabulous introduction to large scale buggies!RACING CHASSIS DESIGN & LAYOUTThe narrow channel chassis made from rigid 4mm 6061 aircraft aluminum and gives the HPI Baja 5B a classic desert racing buggy look and extreme stiffness and durability. The U-shaped chassis is protected at the rear with a thick plastic skid plate for extra protection to the motor and drivetrain.The tube roll cage is made of high impact nylon and topped with a real aluminum roof to carry on the classic looks. The roll cage is fully functional and protects the motor and internals from crash damage. The roll cage, radio box, body panels, wing, undertray and gear case are all mounted with fast access clips for easy maintenance. To finish you need: Engine with clutch and exhaust Remote control with servos and receiver battery Charger Two cans of Lexan paint Features Summary Unassembled 1/5th scale electric-powered Off-Road Buggy Ready for your 6S or 8S LiPo electronics Streamlined HPI Baja 5B Flux body design Adjustable motor mount Adjustable HD shock absorbers Monocoque chassis Low CG for superior handling Long travel suspension Viscous torque oil-filled gear differential All-terrain tires Beadlock wheels with metal insert hubs Aluminum rear shock tower Hard plastic skid plates Adjustable rear wing Quick access to all critical maintenance points Dual bellcrank steering Cam type servo saver Hex socket hardware Gunmetal anodizing Full set of rubber-sealed ball bearings Enclosed receiver box Chassis Specifications Overall Length 817mm Height: 255mm Width: Front - 460mm; Rear - 480mm Tire Track (to center of tires): Front - 395mm; Rear - 400mm Wheelbase: 570mm Ride Height: 76mm Suspension Travel: Front - 95mm; Rear - 100mm Weight: 9.6kg (21.3lb) Adjustable Camber: front - shims; rear - screw Front caster: adjustable with shim 22 / 25.5* / 29 degrees (* stock) Toe-in: Front adjustable with tie rod; Rear adjustable with inserts 0-4 degrees (3 degrees stock set-up) Aircraft aluminum 6061 T6 monocoque chassis Double wishbone suspension with adjustable roll center F/R Drive system: HD metal gears with sealed gear box (8.382:1 gear ratio) Differential: viscous torque control with 4 pinion gears; sealed diff case with silicone oil Shock absorber: HD Aluminum coilover shock absorber with fully adjustable preload collar Wheel type: 3-piece beadlock design, high impact nylon material with inset heavy-duty metal hex hub

€799.00*

Average rating of 0 out of 5 stars

y1613 Mammoth Supergrip mounted and glued on silver FG rims
y1613 Version: Front Medium und Heck Supersoft+ 60EUR
Genuine rc-car-online spare/option part.The optimal parking lot or race tires for your FG Racetruck model.Type Width Outer diameterFront 64 mm 153 mmRear 78 mm 153 mmGlued on original FG-Racetruck rims (rear tire with extension to the inside), incl. foam rubber insert,FG rim with 18 mm square drive and reinforcement ring.Attention: From experience we warn against using rims and extensions from another manufacturer.Since the Mammoth tires provide a very good grip, the rim and bonding are extremely stressed. Due to the high torque load in relation to the bonding of tires on large models, an occasional check in this regard and possibly a repair of the bonding (y0067) is inevitable.As a recommendation:The dirtier the track or the colder the temperature, the softer the rear tire should be.Reference for the front tire: With 2WD models this should be one to two stages harder than the used rear tire. On 4WD models, a tire combination with the same shore hardness front and rear is often good to drive.Of course, with Mammoth Supergrip Racetruck tires, the softer the tire, the higher the wear.The Mammoth Supergrip Racetruck tires have a special onroad tread. Whereby these still have an optimal grip after the wear of the tread, and can still be driven for a long time.

Variants from €89.90*
€149.90*

Average rating of 0 out of 5 stars

y1249 GPM No. 15, Steel pinion 17t and 18t, profile regraded
Regular price: 54,80 EURSteel pinion set with one each 17T and 18T pinion.The GPM steel pinions are profile regraded. This allows for a change in gearing by a pinion swap alone. Module: m=1.5Profile regraded means that the number of teeth is changed while the diameter remained constant. The part of the involutes? curve that defines the tooth profile is changed. Positively regraded (lower number of teeth) pinions are stronger and run smoother, the reduced strength of negatively regraded pinions doesn?t really matter.

€44.90*

Average rating of 0 out of 5 stars

y1203 HS gilmer belt for FG 4WD cars, 1 pce.
Dimensions same as FG 66237.Very high rupture strength and tearing resistance as well as reduced wear make this belt the perfect choicefor race applications where maximum reliability is a must.Fits cars with 490 and 510 mm wheelbase only. Does not fit WB535 cars! For all FG Offroad 4WD models with 490-510mm ( Offroad buggy, monster and stadium) and all FG Sportsline 4WD 510 ( Porsche GT3, Mini and BMW E30 ) leng 635mm, wedth 18mm.

€34.90*
Loading...
Upload in progress, please be patient ...
Shopware-Agency Shopware-Agency