FG tyre heating blankets for 1:5 touring cars 1 pair, used
Product information "FG tyre heating blankets for 1:5 touring cars 1 pair, used"
1 pair of used FG tyre heating blankets for tyre size:
- Maximum 120 mm outer diameter
- Maximum tyre width 80 mm
So for all standard touring car/GT 1:5 tyres!
Not suitable for Formula 1 and truck tyres!
Operating instructions:
The tyre heating blankets may only be operated with 12 - 13.8 volt alternating or direct current. In order to achieve the best possible operating temperature, a power supply unit with 12 - 13.8 volts AC or DC and at least 10 amps output power should be used. The T2m Powerbase y1352 power supply unit is ideal here. Of course, the tyre heating blankets can also be operated directly from a 12 volt (without Powerbase) car battery. To avoid damaging the heating coil in the blankets, they must not be kinked and must not be used without tyres!
Contents:
2 pieces/ 1 pair
The tyre heating blankets have been tested in our workshop.
See photos for condition and scope of delivery.
Login
Similar products
Genuine GPM spare/option part. Complete set for Losi 5ive-T and Mini and brake pads made from high strength aluminium with carbon fiber brake discs.Dimensions disc:Diameter: 60 mmMaterial thickness: 4,2 mmBrakedisk adapter: 16,5 x 27 mmContents:2 x Carbon fiber brake disc2 x outer brake pads2 x inner brake pads
Used perforated clutch bell. Suitable for many 1:5 FG and Carson 2WD models. See photos for condition and scope of delivery. 1 piece
Used perforated Lauterbacher clutch bell. Fits many 1:5 FG and Carson 2WD models. See photos for condition and scope of delivery. 1 piece
Fits FG and Smartech touring cars.The use of steel spur gears on the layshaft increases reliability significantly. Pebbles, heat and shock loads created by high rev clutches are no longer a problem.The carrier is designed for reverse installation as seen on the FG EVO car, where the hubs of pinion and spur gear carrier are pointing to the outside of the car.The carrier features M8 grub screws for installation on the layshaft. This means that the tip of the screw is as wide as the flat area on the shaft and ensures best possible load distribution.The spur gears feature the same diameter as the FG plastic versions. The use of a steel clutch pinion is mandatory with steel spur gears!The spur gears are available as 39T, 40T or 41T versions. The following measures are required for installation of the HT-steel gear adapter "on-road" on the layshaft in FG EVO 2020 cars:- The installed wide 16T layshaft pinion 6431/01 must be replaced by the narrow version 6431.- The supplied 1mm shim must be added between layshaft pinion and ball bearing.- The flat sections on the layshaft do not have the usual 180° offset for the adapter; therefore only one grub screw will be used. However, since this is a wide face M8 version, this is no disadvantage.
Pick up and view possible! Shop hours: Mon. - Fri .: 9:00 to 18:00 / Sat .: 9:00 to 13:00 Checked by our shop, technically sound. Condition see photos.
Pick up and view possible! Shop hours: Mon. - Fri .: 9:00 to 18:00 / Sat .: 9:00 to 13:00 Checked by our shop, technically sound. Including ball bearings. Condition see photos. For many FG and Carson Models.
Condition see photos.
Specifications Max. Current: 195 A
Max. Voltage: 27 V Max. Power: 5,200 W KV (RPM/Volt): 1090 KV Depth of the mounting holes: 8 mm Hole pattern: 4 x M4 on 30 mm bolt circle diameter each Housing diameter: 57.8 mm Housing length: 92 mm Length of shaft: 30 mm Shaft diameter: 8 mm Weight: 960g Connector plug: 8 mm diameter Connection cable: 8AWG Features
High quality ball bearings
4-pole rotor with high-quality magnets
Stator made of super-thin silicon steel
High strength 8 mm shaft
CNC aluminium housing with cooling fins
High temperature resistant copper winding
Content: 1 piece
Used perforated clutch bell. Suitable for many 1:5 FG and Carson 2WD models. See photos for condition and scope of delivery. 1 piece
Here you can purchase a used Samba steel power resonance pipe in mint condition. Complete as shown in the photos with elbow and connector. Total length approx. 300 mm Diameter at the thickest point 65 mm. We do not know the type of resonance tube, so we do not know exactly for which large models the resonance tube is suitable. See photos for condition and scope of delivery.
Fg 4 jaw Teflon clutch adjustable for FG, Carson, HPI, Losi and many other models with long adapter for Zenoah, CY or similar engines, used.See photos for condition and delivery.
Reliable and approved 4-block clutch with teflon linings, adjustable. The well approved clutch was reworked in some details. This clutch is excellent for the use in Off-Road models and is distinguised through reliability and low wear.-used.See photos for condition and delivery.Adjustable and in many details improved 4-block clutch.This clutch is suitable for all FG models and other brands with Zenoah or CY engines.Not suitable for HPI cars.
Customers also viewed
y1351 Version:
y1351/01 One pair
Genuine HT spare/option part. A must-have for 1/5 on-road racing! Even though it looks funny at first sight for uninitiated people! ;-) Just like in full-size racing our tires need a certain temperature to provide the necessary grip that is needed to achieve good lap times. Usually this means that the car will get really fast times only after a few laps. The driver who uses preheated tires has a considerably advantage. With cold outside temperatures or low grip tracks, like a not so clean parking lot, it often not possible at all to bring the tire temperature up to the required range just by driving. As a result the car will be difficult to control! Measures:maximum outer diameter of 130 mm maximum tire width of 80 mmThat includes all standard 1/5 touring car tires! ( ) Instructions: The tire warmers may be operated only on 12 to 13.8 volts AC or DC. In order to reach optimum operating temperature, a power supply with a 12 - 13.8 volts AC or DC and at least 10 amps output power should be used. The T2m Powerbase y1352 is the perfect solution for this application. The operation of the tire warmers directly from a 12 volt car battery (without Powerbase) is also possible, of course. In order to prevent damaging the filament inside the blanket, they must not be bent and not used without tires!Contents:1 set
With this robust and reliable FG chassis, which is equipped with a powerful 26 cm³ combustion engine, you get the ideal entry into the fascinating "royal class" of large scale RC models as well as into the competition.The model has a 530 wheelbase. The models are built on a 4 mm alloy chassis with double wishbones at front and rear axle. All borings of the alloy chassis are countersunk to prevent the screw heads from bearing out. The models are serial equipped with the 2-damper front axle which guarantees an optimal traction of both front wheels. At the front/rear axle you can adjust through track rods or adjusting screws with right-/left-handed thread the king pin angle, trailing effect and toe-in.Further equipment points are differential gear, 24 teeth steel pinion, oil-pressure shock absorbers with volume control and external adjusting ring for the initial spring preload. All rotating parts as shafts, axles and clutch bells a.s.o. are supported by ball bearings.The remote control, the two servos and the receiver battery (RTR set!) are required to operate the FG model. This RTR equipment is available in our shop selection for an additional fee.The body shell is clear, but also available in a painted version in our shop selection for an additional fee.Thanks to the numerous available option parts, you can upgrade your FG Challenge Line as required.You can select the car with complete RTR-equipment from the options menu. RTR-equipment RTR = Ready to Run. The RTR version comes ready to use with the 2,4 GHz rc-system already installed. Transmitter 2,4 GHzReceiverHigh power servo for throttle and brakeLargescale servo for steeringTx-battery, rx-battery Dimensions:Length: 880 mmWidth: 392 mmHeight: 240 mmWheelbase: 530 mm
y1372 Version:
y1372/02 Front and rear+ 109EUR
A must-have for 1/5 on-road racing! Even though it looks funny at first sight for uninitiated people! ;-) Just like in full-size racing our tires need a certain temperature to provide the necessary grip that is needed to achieve good lap times. Usually this means that the car will get really fast times only after a few laps. The driver who uses preheated tires has a considerably advantage. With cold outside temperatures or low grip tracks, like a not so clean parking lot, it often not possible at all to bring the tire temperature up to the required range just by driving. As a result the car will be difficult to control!Measures:maximum outer diameter of 150 mm maximum tire width of 110 mm That includes all standard 1/5th car tires! ( Formular 1 car tires ) Instructions: The tire warmers may be operated only on 12 to 13.8 volts AC or DC. In order to reach optimum operating temperature, a power supply with a 12 - 13.8 volts AC or DC and at least 10 amps output power should be used. The T2m Powerbase y1352 or the LRP 43200 Powersupply Competition power supply is the perfect solution for this application. The operation of the tire warmers directly from a 12 volt car battery (without Powerbase) is also possible, of course. In order to prevent damaging the filament inside the blanket, they must not be bent and not used without tires!Contents:1 pair
Variants from €119.90*
Small steel modul (1,25) transmission set for Sportsline and Challenge Line, improves performance and reliability.
The Mecatech FW01 is for sure the currently most innovative 1/5 race car designed for the dedicated and technically enthusiastic rc car driver.Everyone is enthusiastic about the perfectly fitting and precise workmanship at the highest level. Only high quality materials are used for the production.Since many years Mecatech is a well-know premium manufacturer of largescale hydraulic brakes or shocks and, as only a few may know, a technology expert for a number of Formula 1 racing teams!The Performance Kit from the FW01 is particularly intended for "racer" and differs from the Chassis Kit model by the Performance Kit. Here the list of parts are not including:DifferentialEngine Clutch, Airbox and tuned pipe systembody shell and tiresElectonic components such as servos, batteries and Remote controlPerformance Kit:engine brace left and rightfront stabilizer bar 2.75 mm titanium ready for installationrear stabilizer bar 1.75 mm titanium ready for installationthe two 80 gram front weightsthe two smaller 80 gram center weightsWith the Performance Kit the vehicle is quasi equipped as used at races!Stock gearing:Clutch pinion / spur gear: 36T / 64TLayshaft pinion / differential: 24T / 73TCurrently the Mecatech FW01 is for sure the benchmark of the 1/5 scale racing scene! In the first year Markus Feldmann won with his FW01 1: 5 Mecatech on one of the world's finest and most demanding race track in Lostallo / SwitzerlandMecatech is multiple German, European and World Champion with the FW01 and as the last result:Markus Feldman wins the European Championship in Tourlaville/France. All top 5 positions went to drivers running a Mecatech FW01. 7 out of 10 finalists cars were Mecatech FW01.Although the fit of the Mecatech FW01 parts makes the assembly of the car a great experience, some of our customers want to use the expertise of our shop and wish their FW01 fully assembled and tuned in by us! The complete assembly of your FW01 by our workshop is possible for an additional charge. Please note that the costs of the full assembly with servos a.s.o. do not include the price of any rc-components. If you do not have a suitable radio system with servos and batteries as well as switch and charger, you have to take an additional EUR 800 to EUR 1,500 for this equipment into account. We will be happy to make you an appropriate offer. We are currently waiting for the latest version of the Mecatech FW01. We are currently waiting for the latest version of the Mecatech FW01.Included in the chassis kit:- All pinions- clutch bell- Coupling fixation- All parts and screws for mounting the enginenot included:- differential- Engine and linkage- body shell and spoilers- Airbox- clutch - engine- Electronics- TiresWe are currently waiting for the latest version of the Mecatech FW01.
HTRC charger with extremely easy 1-button operation. It charges the battery types commonly used in car modeling with mains or DC voltage supply. Infinitely adjustable charging current, automatic shut-off and balancer ports for 1S - 6S batteries are built in.Output via 4 mm sockets to accept all charging cables with 4 mm banana plugs! Specifications: AC input voltage: 100 - 240V DC input voltage: 10 - 18V Charging Power: 50W Charge Current Range: 0.1 - 5 A Max balancer current: 300mA / cell LiPo / LiFe cell count: 1 - 6 cells NiCd / NiMH battery cell count: 1 - 15 cells Size: 145 x 80 x 44 mm Weight: 170 g Content: 1 x HTRC H6AC/DC charger 1 x T- connector charging cable 1 each adapters T-connector to BEC / Futaba / JR / alligator clips 1 x Mains cable 1 x DC input cable 1 x Instruction manual