6463 FG carburetor cooling

€9.60*

Prices incl. VAT plus shipping costs

Available

Product number: fg_6463

EAN: 3410569530684

Product information "6463 FG carburetor cooling"

Genuine FG spare/option part.

For redirecting cool air from the flywheel towards the carburetor.

Contents:

1 piece

0 of 0 reviews

Leave a review!

Share your experiences with other customers.

Login

Your email address

Your password

Display reviews in current language only.

No reviews found. Share your insights with others.

Similar products

y1312 Twin hose bracket

Twin hose bracket for hoses up to 7 mm outer diameter. With 5 mm hole for installation by screw or cable tie.Keeps your car's fuel lines in place. Especially helpfull with tuned pipe layouts running close to the engine.Screws with part number #6726/25 are recommended for installation on the fan cover.

From €14.90*

Details

GPM Starter cover, no. BJPSCO

Keeps cool air coming to your engine by keeping dirt and grass from clogging up the pull starter area. Easily wipe off anything not deflected away. Installs on the starter cover with hook & loop tape. With metal cable management.If using a FG monster / stadium model an additional hole for the support of the lateral carrier plate has to be cut out.

€25.60*

y0811 After-Run, performance enhancing preservation for all 1/5 and 1/6th scale models, 20 ml

Genuine HT spare/option part. After-Run is a performance enhancing preservation, which ensures that the engine starts properly, even after a long time (winter break) storage. Added to the fuel it keeps the fuel system clean.Among other After-Run conserves the diaphragm of the Walbro carburetor!For long term storage (i.e. during winter!) "vital" for the carburetor diaphragms!For 23 to 32 cm³ engines like Zenoah, Chung Yang, PT, Losi, HPI a.s.o.It binds water in the fuel, particularly important when the engine is not run regularly or after wet races. After-Run improves engine performance, ensures better combustion, removes debris and residues. Simply add the content of the bottle to 5 litres of fuel.Contents:1 piece / 20 ml

Content: 20 Milliliter (€395.00* / 1000 Milliliter)

€7.90*

GPM Air filter cover, no. BJAFCO, 1 pce.

GPM air filter cover which fits easily over your existing air filter. A rubber band at the bottom holds the cover in place. Maintenance of the main filter will be significantly reduced, especially in very dusty environments. Fits all common filters, foam or fabric (K&N) style.

€13.30*

y0518 Hobbythek service bag

Genuine HT spare/option part. Special fabric bag to protect engines, rc-plates or other expensive items. Large opening and pull-string closure.Size:Diameter 200 mmHeight 200 mmContents:1 pieceAccessories not included.

€6.50*

y0040 KENT hose quick couplings for all 1/5 & 1/6 cars

y0040 Variant: y0040 Coupling member A and B

The secure hose connection for engine or tank removal! Advantages of the Kent system quick couplings: A safe opening and closing with one hand, as soon as one side is fixed. The design of the "shut-off" valve is a double chamber system, which closes when disconnecting the coupling. (This design enables easy and safe opening of the quick couplings, even under high pressure. Similarly, just as in low pressure applications.) You feel a snap when connecting the couplings, preventing over-tightening or accidental opening. The actions of opening and closing the quick couplings are identical, so that the handling is extremely simple. An ergonomic design guarantees easy handling, yet the space requirement for the couplings is low. Long and safe life of the couplings even with frequent connection and disconnection. In order to protect the fully encapsulated KENT quick coupling system against dirt even after dismantling, sealing the ends with the corresponding white plugs and caps is recommended.

€16.90*

ST-FTCO-BK GPM Air filter cover for Losi 5IVE-T

GPM air filter cover which fits easily over your existing air filter. A fastening band band at the bottom holds the cover in place. Maintenance of the main filter will be significantly reduced, especially in very dusty environments.

€13.30*

7323/08 FG Complete pull start unit for CY / Zenoah / Fuelie / Losi engines

fg_7323_08 Zenoah Label: Without label

Genuine FG spare/option part. Complete starter unitPull start unit for CY / Zenoah G230/240/260/270/290/320.Contents:1 piece

€39.90*

y1344 GPM Air filter cover for Losi Desert Buggy XL/2.0

€13.30*

6061 Mielke pull starter with hybrid starter function

Genuine Mielke spare / option part.Starting by pull starter or by cordless screwdriver or electric starter is possible.Pull starter with hybrid starter function. Who does not know it? A torn starter rope, blisters on your finger from constant pulling or a defective starter pawl. All these problems are a thing of the past with the hybrid starter.With the help of a cordless screwdriver the engine can be started very easily and if the battery of the cordless screwdriver is empty, the engine can be started by using the conventional way with the pull-rope starter.Please note:The starter shaft for electric start is inserted in a straight line in extension of the crankshaft. No part of the vehicle must be in the way here. On a model with a longitudinally mounted engine (e.g. Losi 5ive or DBXL vehicles) the rear axle will usually prevent the use of the electric start. The normal pull start by cable remains possible.Contents:1 piece

€114.90*

TT1031 TopTuning Carburetor heat sink for all Zenoah/CY/HPI/Losi and PT (Smartech!) engines

Original TopTuning spare/option part. Carburetor heat sink for all Zenoah/CY/HPI/Losi and PT-Smartech/Carson engines.Fits all Walbro 603/813/990/771/527/1107 carburetors as well as all Smartech/Carson PT engine carburetors and many more!The TopTuning carburetor heat sink counteracts the notorious vapor lock at high engine temperatures.In fact all current large scale engines have a special adaptor for the thermal insulation of the carb (isolator) to keep the carb as cool as possible, so that the fuel does not form bubbles due to heat transfer from the cylinder. And without this isolator the gasoline would literally cook after a short operating time and therefore the engine would receive a leaner mixture. The much feared lean-out until the engine stalls is inevitably.Unfortunately, even a special isolator is often insufficient at higher ambient temperatures or when the engine is subjected to higher loads, e.g. in racing. In such scenarios the better heat dissipation of the Top Tuning carburetor heat sink contributes to the solution of the problem.The easy to install heat sink, requires a considerable manufacturing and milling effort and fits easily to all common 1:5/1:6 large scale cars, such as FG, Mecatech, Smartech/Carson, HPI, Losi, etc..For installation in FG 4WD cars the rear cross member # 66212 must be modified.Attention: the Allen head screw is an imperial size and therefore not compatible with metric Allen wrenches! Available in our options menu Content: Carburetor heat sink 1 x Allen head screw #8-32 x 5/8" (for Walbro carbs) 1 x washer 4 mm

€39.90*

y1105 Exhaust port and carburetor intake cover plates, for most usual 23cc - 30cc engines

Exhaust port and carburetor intake cover plates, made of 1 mm aluminum, fits most current 23cc - 30cc rc-car engines.Exhaust port cover:Total: approx. 20 x 45 mmMounting holes (ctr./ctr.): approx. 34 mm carb intake cover:Total: ellipse approx. 28 x 40 mmMounting holes (ctr./ctr.): approx. 31 mm

€4.90*

Customers also viewed

y0741 Aluminum air filter adapter for Losi 5ive-T with velocity stack, 1 pce.

The aluminum air filter adapter replaces the plastic base plate with the same dimensions of a 5ive-T (not 2.0!) air filter. Its rigidity ensures a reliable seal to the carburetor. It will not warp; neither by high temperatures nor by tightening the mounting screws.This Venturi-insert/adapter prevents that unfiltered intake air perhaps comes into the engine!The additional velocity stack will simply be inserted into the cage for the inner filter foam. It conceals the mounting screws almost completely, providing excellent flow characteristics and improved performance.Comes complete with installation hardware and gaskets included.Scope of delivery1x Air filter adapter2x Countersunk screw 5x501x Carburetor gasket1x Air filter gasket

€39.90*

TT1000 Top Tuning Electronic 20 Amp Bigscale high voltage 30 Volt switch

tt_tt1000 Connector: TT1000/01 Universal in - Universal out

Genuine Top Tuning spare/option part. Top Tuning The 20-amp Bigscale switch allows for a maximum input voltage of 30 volt. It is specifically designed as a receiver switch for use in combination with the Hitec HS-1005SGT servo and 4s receiver battery. The switch can also be used for other applications at your discretion with batteries up to 6S.Note: Top Tuning the electronic 20 amp Bigscale high voltage switch delivers the batterys full voltage. It does not replace a voltage regulator! The components which follow down the line (voltage regulator / servos / receiver) must be matched to this voltage! Using the latest MOSFET technology allows the 20 amp Bigscale high voltage switch to handle extreme loads, despite its small size. A blue LED status light clearly displays the activated mode. The 20 amp Bigscale high voltage switch is dust-and splash protected. He has an extremely low internal resistance and very low power consumption in off mode. Nevertheless it is recommended to unplug the battery when the model will not be used for an extended period. Properties:Voltage range: 3 to 30 VLoad: 20 ampsStandby consumption: 17 µAOperating temperature: - 15 ° C to +50 ° CCable length:Battery side 250 mmReceiver side 130 mmWeight: 13 gramsDimensions:Length: 29 mm Width: 13 mmHeight: 12 mmContents:1 piece

€39.90*

Samba 4110 for Off-Road and monster models 2WD/4WD tuned pipe

Genuine Samba spare/option part.Samba announced this pipe as the monster model / Off-Road pipe, but it fits Beetle/Pajero/Monster Beetle/Monster Truck and 2WD/4WD FG models as well. Will fit Carson CPT as well with some minor modification to the body shell in the bed area.The large distance between pipe and tire is a big advantage especially for the Monster models. The mounting wire is already bent into the correct shape for easy installation.Complete system with steel manifold and hardware for installation included.Content:1 set

€199.90*

This product is no longer available.