TT1031 TopTuning Carburetor heat sink for all Zenoah/CY/HPI/Losi and PT (Smartech!) engines

€39.90*

Prices incl. VAT plus shipping costs

Available

Product number: tt_tt1031

EAN: 4058575144656

Supplies

y0037/06 9/64 Allen key wrench

9/64 Allen key wrench for the imperial size mounting screw of the carburetor heat sink on Walbro carbs.

€4.90*

Product information "TT1031 TopTuning Carburetor heat sink for all Zenoah/CY/HPI/Losi and PT (Smartech!) engines"

Original TopTuning spare/option part.

Carburetor heat sink for all Zenoah/CY/HPI/Losi and PT-Smartech/Carson engines.

Fits all Walbro 603/813/990/771/527/1107 carburetors as well as all Smartech/Carson PT engine carburetors and many more!

The TopTuning carburetor heat sink counteracts the notorious vapor lock at high engine temperatures.

In fact all current large scale engines have a special adaptor for the thermal insulation of the carb (isolator) to keep the carb as cool as possible, so that the fuel does not form bubbles due to heat transfer from the cylinder. And without this isolator the gasoline would literally cook after a short operating time and therefore the engine would receive a leaner mixture. The much feared lean-out until the engine stalls is inevitably.

Unfortunately, even a special isolator is often insufficient at higher ambient temperatures or when the engine is subjected to higher loads, e.g. in racing. In such scenarios the better heat dissipation of the Top Tuning carburetor heat sink contributes to the solution of the problem.

The easy to install heat sink, requires a considerable manufacturing and milling effort and fits easily to all common 1:5/1:6 large scale cars, such as FG, Mecatech, Smartech/Carson, HPI, Losi, etc..

For installation in FG 4WD cars the rear cross member # 66212 must be modified.

Attention: the Allen head screw is an imperial size and therefore not compatible with metric Allen wrenches! Available in our options menu

Content:

Carburetor heat sink
1 x Allen head screw #8-32 x 5/8" (for Walbro carbs)
1 x washer 4 mm

0 of 0 reviews

Leave a review!

Share your experiences with other customers.

Login

Your email address

Your password

Display reviews in current language only.

No reviews found. Share your insights with others.

Similar products

y1312 Twin hose bracket

Twin hose bracket for hoses up to 7 mm outer diameter. With 5 mm hole for installation by screw or cable tie.Keeps your car's fuel lines in place. Especially helpfull with tuned pipe layouts running close to the engine.Screws with part number #6726/25 are recommended for installation on the fan cover.

From €14.90*

Details

GPM Starter cover, no. BJPSCO

Keeps cool air coming to your engine by keeping dirt and grass from clogging up the pull starter area. Easily wipe off anything not deflected away. Installs on the starter cover with hook & loop tape. With metal cable management.If using a FG monster / stadium model an additional hole for the support of the lateral carrier plate has to be cut out.

€25.60*

y0811 After-Run, performance enhancing preservation for all 1/5 and 1/6th scale models, 20 ml

Genuine HT spare/option part. After-Run is a performance enhancing preservation, which ensures that the engine starts properly, even after a long time (winter break) storage. Added to the fuel it keeps the fuel system clean.Among other After-Run conserves the diaphragm of the Walbro carburetor!For long term storage (i.e. during winter!) "vital" for the carburetor diaphragms!For 23 to 32 cm³ engines like Zenoah, Chung Yang, PT, Losi, HPI a.s.o.It binds water in the fuel, particularly important when the engine is not run regularly or after wet races. After-Run improves engine performance, ensures better combustion, removes debris and residues. Simply add the content of the bottle to 5 litres of fuel.Contents:1 piece / 20 ml

Content: 20 Milliliter (€395.00* / 1000 Milliliter)

€7.90*

GPM Air filter cover, no. BJAFCO, 1 pce.

GPM air filter cover which fits easily over your existing air filter. A rubber band at the bottom holds the cover in place. Maintenance of the main filter will be significantly reduced, especially in very dusty environments. Fits all common filters, foam or fabric (K&N) style.

€13.30*

y0518 Hobbythek service bag

Genuine HT spare/option part. Special fabric bag to protect engines, rc-plates or other expensive items. Large opening and pull-string closure.Size:Diameter 200 mmHeight 200 mmContents:1 pieceAccessories not included.

€6.50*

y0040 KENT hose quick couplings for all 1/5 & 1/6 cars

y0040 Variant: y0040 Coupling member A and B

The secure hose connection for engine or tank removal! Advantages of the Kent system quick couplings: A safe opening and closing with one hand, as soon as one side is fixed. The design of the "shut-off" valve is a double chamber system, which closes when disconnecting the coupling. (This design enables easy and safe opening of the quick couplings, even under high pressure. Similarly, just as in low pressure applications.) You feel a snap when connecting the couplings, preventing over-tightening or accidental opening. The actions of opening and closing the quick couplings are identical, so that the handling is extremely simple. An ergonomic design guarantees easy handling, yet the space requirement for the couplings is low. Long and safe life of the couplings even with frequent connection and disconnection. In order to protect the fully encapsulated KENT quick coupling system against dirt even after dismantling, sealing the ends with the corresponding white plugs and caps is recommended.

€16.90*

ST-FTCO-BK GPM Air filter cover for Losi 5IVE-T

GPM air filter cover which fits easily over your existing air filter. A fastening band band at the bottom holds the cover in place. Maintenance of the main filter will be significantly reduced, especially in very dusty environments.

€13.30*

7323/08 FG Complete pull start unit for CY / Zenoah / Fuelie / Losi engines

fg_7323_08 Zenoah Label: Without label

Genuine FG spare/option part. Complete starter unitPull start unit for CY / Zenoah G230/240/260/270/290/320.Contents:1 piece

€39.90*

y1344 GPM Air filter cover for Losi Desert Buggy XL/2.0

€13.30*

6061 Mielke pull starter with hybrid starter function

Genuine Mielke spare / option part.Starting by pull starter or by cordless screwdriver or electric starter is possible.Pull starter with hybrid starter function. Who does not know it? A torn starter rope, blisters on your finger from constant pulling or a defective starter pawl. All these problems are a thing of the past with the hybrid starter.With the help of a cordless screwdriver the engine can be started very easily and if the battery of the cordless screwdriver is empty, the engine can be started by using the conventional way with the pull-rope starter.Please note:The starter shaft for electric start is inserted in a straight line in extension of the crankshaft. No part of the vehicle must be in the way here. On a model with a longitudinally mounted engine (e.g. Losi 5ive or DBXL vehicles) the rear axle will usually prevent the use of the electric start. The normal pull start by cable remains possible.Contents:1 piece

€114.90*

y1105 Exhaust port and carburetor intake cover plates, for most usual 23cc - 30cc engines

Exhaust port and carburetor intake cover plates, made of 1 mm aluminum, fits most current 23cc - 30cc rc-car engines.Exhaust port cover:Total: approx. 20 x 45 mmMounting holes (ctr./ctr.): approx. 34 mm carb intake cover:Total: ellipse approx. 28 x 40 mmMounting holes (ctr./ctr.): approx. 31 mm

€4.90*

AT-AT001 ATOP Colored high flow fuel line with connections and accessories for Losi 5ive-T/2.0/B, Mini and HPI models

at_at001 Color: AT-001/02 - Red

Genuine Atop spare/option part. Colored fuel hose with clams and suction tubesArea Rc High flow fuel line kit.This high flow fuel line kit fits the HPI Baja series and the Losi 5ive-T/B and Mini. It may fit other large scale cars as well.The kit comes with 6 pieces of fuel line clips and 2 assembled plastic fittings. Those fittings cannot be compressed by the tanks fuel line grommet, so the inner diameter remains constant which improves fuel delivery to the carb.Fuel line dimensions:Length: 1mInside diameter: 3 mmOuter diameter: 6 mmAvailable colors: AT001/01 - YellowAT001/02 - RedAT001/03 - BlueAT001/05 - GreenIncludes:2 x Assembled plastic fittings6 x Fuel line clipsTygon fuel line

€17.90*

Customers also viewed

y1430 Spark plug tester for 1/5 & 1/6 cars

The spark plug tester wiil be put in line between the spark plug in the engine and the spark plug cap. When the spark plug is in good working order, pulling the recoil starter will produce a spark easily visible in the clear section of the tester (see video!).

€14.90*

y0809 Klüber high performance grease for differentials

Freaking expensive, but it is damned fine.ASONIC HQ 72-102 is a synthetic high-temperature lubricating grease, for use in limited slip differentials. Due to the careful selection of product components and the clean manufacturing environment, ASONIC HQ 72-102 is a rolling bearing grease with a particularly low noise level.Benefits for your application:High-temperature lubricating grease for rolling bearingsHigh purityLow noiseGood water resistanceContent:1 piece, tube with 30g

Content: 30 Gramm (€730.00* / 1000 Gramm)

€21.90*

Losi 5ive-T Race body with cage, used

1 piece Losi 5ive-T Race body tipped and painted with cage, used. The body has damage and cracks. See photos for scope of delivery and condition.

€149.90*

y0994 Marston heat-proof sealer - 1pce.

Marston Universal blue is the leading non-setting gasket and sealing compound in use world-wide. The product is used by many of the world?s major automotive manufacturers and by several Formula 1 teams.Features- Non hardening and non setting- Unlimited assembly time- Vibration resistant- Allows metal to metal contact- Resistant to combustion products, water, engine coolant, petroleum, lubricating oils, kerosene and fluorocarbon refrigerants- Seals surface imperfections- Withstands rapid variations in temperature80 ml tube

Content: 80 Milliliter (€123.75* / 1000 Milliliter)

€9.90*

7356/08 FG Air filter for CY / Zenoah

Genuine FG spare/option part. Air filter has no choke. Not suitable for offroad use!Contents:1 piece

€19.70*

y1246, Hobbythek/GPM Dirt-Cover line for FG, Carson/Smartech and Conrad cars, set

Regular price: 51,80 EURhe set is suitable for all FG models + Carson/Smartech/Reely (not for FG Leopard + Carson Gas Devil, Hell Devil, CRT 4x4, Smartech Thunderbolt), please use order no. y1247.Content of delivery:- y0514 GPM Shock-Cover für FG, Carson, Smartech, Conrad- GPM Air filter cover, no. BJAFCO- GPM Starter cover, no. BJPSCO y0514 GPM Shock-Cover für FG, Carson, Smartech, ConradThese protective covers prevent the shock piston rods and seals from wear caused by dirt. They fit most 1/6 and 1/5 scale shocks. Not for Gas Devil, Thunderbolt, Helldevil, CRT 4x4!- total length 150 mm for all FG / Carson / Smartech / Conrad and all shocks with a spring diameter from 22 to 30 mm.Set of 4GPM Air filter cover, no. BJAFCOGPM air filter cover which fits easily over your existing air filter. A rubber band at the bottom holds the cover in place. Maintenance of the main filter will be significantly reduced, especially in very dusty environments. Fits all common filters, foam or fabric (K&N) style.GPM Starter cover, no. BJPSCO Keeps cool air coming to your engine by keeping dirt and grass from clogging up the pull starter area. Easily wipe off anything not deflected away. Installs on the starter cover with hook & loop tape. With metal cable management.When using the FG monster / stadium model is cut an additional hole for the support of the lateral support plate.

€39.50*

TT0900 Top Tuning electric starter 2.0 for most 1/5 and 1/6 cars

The new TT0900 electric starter is pre-assembled and fits a wide range of models including the Losi 5ive-T, 5ive Mini and DBXL, most FG models, HPI-Baja / Wild Attack series etc. The TT0900 electric starter can be started with the remote control (free channel required!). The new TT0900electric starter has much more power than the previous Electric starter thanks to the brushless motor and higher voltage. The popular Zenoah G320 is no longer a problem. It also no longer uses a one-way bearing, which clearly increases reliability. Also the installation space has been noticeably reduced by the motor and a planetary gearbox.The starter components to be fitted weigh about 666 grams plus the battery.For mounting the starter, the flywheel on the engine is replaced by the version with spring-loaded pawls included in the delivery. The tools required for this, piston stopper and flywheel puller, are also included in the delivery.For the 3rd channel the transmitter should have a switch with two positions (momentary switch preferred) or a controller. An additional channel is required for a remote engine killswitch. A killswitch is included in the scope of delivery, but a real fail-safe module such as TT0990 offers higher safety. A possibly already existing failsafe module can also be used.Due to the splitting of the functions engine start and engine stop on two channels, no more compatibility problems with different remote controls are to be expected, only the availability of free channels matters.A 3S LiPo battery is required as the power source.In the shops options menu, we offer a special battery with a more compact design (5,600 mAh/30C, 110 x 49 x 34 mm) which makes installation usually easier in many cars, as well as a battery with standard dimensions (3,900 mAh/60C, 135 x 45 x 25 mm). Of course, other 3S batteries can also be used at your own discretion, but the load capacity (capacity x C-rate) should be on a similar or higher level.Please note that we cannot ship batteries to countries outside the European Union!Since the starter unit can be mounted vertically or horizontally and the brushless starter motor is very small, almost all air filters and most tuned pipe systems can be used.Notes regarding necessary modifications known to us for mounting the starter depending on the vehicle: FG 4wd onroad Rear r/h plastic body mount, depending on position, slightly modified or relocated FG 2wd onroad horizontal engine No modifications Mecatech FW01 No modifications FG 4wd Buggy sportsline Depending on the body shell, minor trimming is required. FG 2wd Buggy current chassis Depending on the body shell, minor trimming is required. FG 2wd Marder (old chassis) Starter fits without modifications to the chassis plate. However, the body shell has to be cut out a bit more seriously in the area of the starter. A repositioning of the rear r/h body mount is recommended. FG Monster Cut the r/h side panel slightly and add a flat area to the aluminum tube which supports the panel on the engine Losi 5ive-B Depending on the tuned pipe, mount starter with motor on top or on the l/h side. Losi 5ive-B Mount the starter motor on the l/h side, space for the tuned pipe is very tight and must be tested in each individual case. No problems when using the stock muffler box. Losi DBXL Depending on the tuned pipe, mount starter with motor on top or on the l/h side. If the starter motor is to be mounted on the side, one screw of the motor roll cage must be replaced by a CSH screw. Carson C5 Only with Zenoah or CY engine, not with Smartech PT engine (different hole pattern on engine)! Carson C6 With the C6, depending on the body shell, trimming is required. HPI 5B/T Depending on the body shell, minor trimming is required. Carson Wild GP Attack Depending on the body shell, minor trimming is required. The accommodation of the engine killswitch, controller unit and wiring harness must be carried out at your own discretion. User Manual FG 4WD On-Road FG Monster FG 2WD On-Road horizontal engine FG 2WD/4WD Buggy current chassis Losi 5ive-T Losi DBXL FG 2WD Marder (old chassis)

€349.90*