6293/01 FG Tuning pipe 1:6 - 1pce.
€110.95
Currently unavailable
Product information "6293/01 FG Tuning pipe 1:6 - 1pce."
Lebacher Strasse 4
66113 Saarbrücken
Germany
Login
Accessories / Spare parts
Genuine HT spare/option part. RC Tech Pipe Protect protects your exhaust against oil and rubber deposit while racing. A clean exhaust gives better resonance, which means better performance from your engine. Thanks to RC Tech Pipe Protect your exhaust system can evacuate the temperature better.Direction of useSpray a relatively thick layer of Pipe Protect from a close distance; +/- 15/20 cm on your new or just-cleaned and preferably polished exhaust pipe. After each ride clean the exhaust pipe with a clean cloth, if necessary slightly sprayed with some Pipe Protect. Treat the exhaust pipe again before each race.Contents:1 piece / 400 ml
Content: 400 Milliliter (€24.75 / 1000 Milliliter)
Especially for installation of all engine gaskets. Temperature resistant from -55 °C to +200 °C. Resistant to water, mineral oils, synthetic lubricants, fuels, organic solvents and refrigerants. info: Hand tight: 10 - 20 minReady to use: 1 - 3 hoursGap fill: 0.5 mmContent: 50 ml Notes for usage: This surface seal is not for use as the sole sealant, it should always be applied in combination with a paper gasket.The HT-surface sealing agent should be sparsely applied over the entire surface, with care being taken that the sealant does not enter the devices internals (e.g. crankcase, differential a.s.o.) during the assembly.
Content: 50 Milliliter (€538.00 / 1000 Milliliter)
Customers also viewed
Der neue Allrad-Wettbewerbsbuggy Leo 3 ist mit drei Differenzialen ausgestattet. Diese neue Version ist von den 1/8 Wettbewerbsbuggys inspiriert. Durch die sehr direkte Kraftübertragung wird mehr Leistung generiert. Die Zentralbremse ist im Differential- Bock integriert. Das Modell ist mit einem Chassis aus gefrästem 5 mm T7075-Aluminium, großvolumigen Stoßdämpfern, ein Resonanzschalldämpfer und einer neuen aerodynamischen Karosserie ausgestattet. Der Motor (separat zu erwerben) wird in der Mitte mit einer Neigung zur Optimierung des Schwerpunkts eingebaut. Die Wartung dieses Modells wird durch einen schnellen Ausbau der einzelnen Teile erleichtert. Das Modell wird ohne Motor, Kupplung, Airbox und RC-Anlage geliefert.Abmessungen : Länge : 770mm Breite : 470mm Hohe : 330mm Radstand : 580mm Gewicht : 13.2kgNicht inbegriffen : Motor 26cc, 29cc Kupplung Airbox RC-Anlage
For FG 1/6 4WD competition cars only.Not suitable for conversion of an FG Sportline 4WD models since several small parts required for the swap are not included. As an alternative use item no. y0497.Suitable ball bearing for the layshaft: 6036/05 FG bearing set 10x19x7 with grease filling - 2 pcs
Genuine FG spare/option part. Body shell is delivered clear and without window gitter or decal set.Dimensions:Length: 580 mmWidth: 240 mmHeight: 205 mmContents:1 piece
Tuned pipe exhaust system for racing, fits near all FG 4WD Off-Road and Monster models from the top manufacturer of high performance exhaust systems. Top quality and optimized performance througout the entire engine's RPM range. Complete set with steel manifold and hardware for sealing and installation. Fits:FG Baja Buggy 2WD/4WDFG Marder 2WD/4WDFG Beetle 2WD/4WDFG Monster/Stadium Truck 2WD/4WDFG Monster/Stadium Hummer 2WD/4WDFG Monster/Stadium Jeep 2WD/4WDCan also be used for 530 mm wheelbase off-road Monster/Hummer and shorter wheelbases. Please note that modifications to the body shell are usually required.Due to the increased performance we recommend the use of aluminum engine mounts.
Reasonable priced 3-chamber aluminum tuned pipe, fits FG Marder/Beetle/Pajero and Carson Attack. Comes with manifold, teflon tube, hose clamps and mounting wire included.Also fits Comanche, CRT, CPT
Genuine FG spare/option part. Contents:1 set