Skip to main content Skip to search Skip to main navigation
EXTRA 20% off Outlet*. Use Code: EXTRA20 at checkout!!
+49 2151 820200 Mon-Fri 9 am - 6 pm, Sa 9 am - 1 pm

6079/01 FG Rear axle shaft for ball drive

Product information "6079/01 FG Rear axle shaft for ball drive"

Genuine FG spare/option part.

For ball drive system only!
Diameter: 8 mm.

Contents:
  • 1 piece

0 of 0 reviews

Average rating of 0 out of 5 stars

Leave a review!

Share your experiences with other customers.


Accessories / Spare parts

Average rating of 0 out of 5 stars

y1218 Springs for drive shafts
Genuine HT spare/option part. The best solution for drive shaft positioning, can be used with ball drives or regular "dog bones" as well.The springs will be simply inserted into the drive cups.DImensions:Diameter: 11 mmHeight: 8 mmContents:4 piece

€4.90*

Average rating of 0 out of 5 stars

y1004 Driveshaft boots for ball drive + dogbones
Genuine HT spare/option part. Protect ball drive as well as cardan drive against dirt. For FG and Carson ball drives, fits standard dogbones as well.Contents:2 pieces

€8.90*

Alternatives

Average rating of 0 out of 5 stars

GPM 6079/01 Ball drive wheel shaft for all FG and Mecatech cars, 1 pce.
Fits all FG cars and the Mecatech FW01. The GPM drive parts are made of high quality spring steel and due to its elasticity provide high impact resistance and extreme stability. Ground bearing seats ensure maximum accuracy of fit. Ball drives run significantly smoother and with less wear than normal dog bones with pins. The GPM ball drives can be partially mixed with FG parts. The heads of the GPM driveshafts fit into FG differential cups or wheel shafts.The opposite combination, i.e. FG shafts in GPM differential cups or wheel shafts does not always fit. We had tests where some FG shafts fit neatly, but due to slight tolerances others who did not fit into the very same cups/shafts. For this combination, we can not guarantee compatibility! Dimensions: Diameter: 8 mmTotal length 76.6 mm

From €32.90*

Average rating of 0 out of 5 stars

y1004 Driveshaft boots for ball drive + dogbones
Genuine HT spare/option part. Protect ball drive as well as cardan drive against dirt. For FG and Carson ball drives, fits standard dogbones as well.Contents:2 pieces

€8.90*

Average rating of 0 out of 5 stars

y1218 Springs for drive shafts
Genuine HT spare/option part. The best solution for drive shaft positioning, can be used with ball drives or regular "dog bones" as well.The springs will be simply inserted into the drive cups.DImensions:Diameter: 11 mmHeight: 8 mmContents:4 piece

€4.90*

Similar products

Average rating of 0 out of 5 stars

6069/01 FG Differential axle spline drive
Genuine FG spare/option part.For all FG cars with standard drive shafts (no ball drive). Accepts dogbones with 10 mm ball and 4 mm pin.Dimensions:Shaft, diameter: 8 mmLength: 27 mmSpline drive for FG bevel gearsCup, diameter: 18,5 mmLength 14 mmContents:1 piece

€27.90*

Average rating of 0 out of 5 stars

6077/05 FG Steel ball 10x13mm for rear upright - 2pcs.
Steel ball for rear upright.5 mm bore diameter

€8.50*

Average rating of 0 out of 5 stars

6080 FG Rear dogbone
Genuine FG spare/option part. Replacement drive shaft (dogbone). Long Version.Suitable for BMW GTR, Mercedes CLK-GTR, Race-Trucks, C291, Porsche GT1, GT2, GT3 and all FG Off-Road models.Dimensions:Shaft diameter: 7 mmBall diameter: 10 mmLength: 101,5 mmContents:1 piece

€17.90*

Average rating of 0 out of 5 stars

6065/01 FG Plastic diff. cover
Original FG Ersatz-/Tuningteil.Well-priced but still effective plastic diff. cover. Stones can damage metal covers and it is difficult to removethem. According to the flexible plastic material an impressing becomes hardly possible. If it still happens the cover can be easily removed through cutting with a knife or a scissors.Dimensions:Length: 43 mmDiameter: 45 mmFlange diameter: 65 mmInhalt:1 Stück

€6.90*

Average rating of 0 out of 5 stars

6081/01 FG Steel ball Ø5mm 10x15 mm
Genuine FG spare/option part. Ball joint with 5mm bore suitable for all FG plastic ball-and-socket joints.Contents:4 pieces

€16.90*

Average rating of 0 out of 5 stars

6079/05 FG Ball driving axle M8
Original FG Ersatz-/Tuningteil.Inhalt:1 Stück

€35.90*

Average rating of 0 out of 5 stars

6071 FG Alloy rear axle brace
Genuine FG spare/option part. Suitable for all FG models except Formula 1 and Evo. Mounting holes for 4 mm bolts.Contents:1 piece

€17.00*

Average rating of 0 out of 5 stars

6057 FG Window grid r/h
Genuine FG spare/option part. Suitable for 6154, 6155, 6154/03.Dimensions:Width: 195 mmHeight: 80 mmContents:1 piece

€15.90*

Average rating of 0 out of 5 stars

6077/08 FG Spacer bushing for rear upright
Genuine FG spare/option part. Only suitable with standard size ball bearings.Dimensions:Length: 10 mmOuter diameter: 11 mmInner diameter: 8 mmContents:2 pieces

€4.50*

Average rating of 0 out of 5 stars

6058 FG Window grid front
Genuine FG spare/option part. Suitable for 6154, 6155, 6154/03.Dimensions:Width: 115 mmHeight: 110 mmContents:1 piece

€15.90*

Average rating of 0 out of 5 stars

6064 FG Differential case
Genuine FG spare/option part. Stock plastic differential case. Also available in aluminum.Dimensions:Length: 70 mmDiameter: 42.5 mmFlange diameter: 65 mmBearing seats: 12 x 8 mmShaft bore: 8 mmInner dimensions: 40 x 30 mmContents:1 piece

€25.50*

Average rating of 0 out of 5 stars

6072/02 FG Rear lower wishbone adjustable for Monster-Truck
Genuine FG spare/option part. Contents:1 piece

€19.90*

Customers also viewed

Average rating of 0 out of 5 stars

6079/05 FG Ball driving axle M8
Original FG Ersatz-/Tuningteil.Inhalt:1 Stück

€35.90*

Average rating of 0 out of 5 stars

6079 FG Rear axle shaft
Genuine FG spare/option part. Dimensions:Total length 73 mmLength of M6 thread section 11 mmLength of 8 mm shaft incl. thread 59 mmLength of drive cup 14 mmContents:1 piece

€28.90*

Average rating of 0 out of 5 stars

68276 FG Front wheel shaft 2WD/4WD
Genuine FG spare/option part. Diameter 8 mm.Contents:1 pieceFor older 2WD models that are not based on the 4WD models, please refer to Sportsline 2008. or if an RC plate is no longer fitted, check Sportsline 13 in Parts Scout.There you will find the right spare parts for your vehicle.

€18.90*

Average rating of 0 out of 5 stars

6063/05 FG bearing set 12x28x8 with grease filling - 2 pcs
Item N° 6063/5 FG bearing set 12x28x8 with grease filling - 2 pcs

€10.90*

Average rating of 0 out of 5 stars

GPM 6079/01 Ball drive wheel shaft for all FG and Mecatech cars, 1 pce.
Fits all FG cars and the Mecatech FW01. The GPM drive parts are made of high quality spring steel and due to its elasticity provide high impact resistance and extreme stability. Ground bearing seats ensure maximum accuracy of fit. Ball drives run significantly smoother and with less wear than normal dog bones with pins. The GPM ball drives can be partially mixed with FG parts. The heads of the GPM driveshafts fit into FG differential cups or wheel shafts.The opposite combination, i.e. FG shafts in GPM differential cups or wheel shafts does not always fit. We had tests where some FG shafts fit neatly, but due to slight tolerances others who did not fit into the very same cups/shafts. For this combination, we can not guarantee compatibility! Dimensions: Diameter: 8 mmTotal length 76.6 mm

From €32.90*

Average rating of 0 out of 5 stars

FG Sportsline 2WD-530 with Super Street Truck body
Former: "Mercedes 1834" Truck.The Sportsline 08 quality at a reasonable price for beginners. The Sportsline series is ideal for car modellers whose main focus is not just the chassis, but rather the combination of chassis and body shell.You can select the car with complete RTR-equipment from the options menu. RTR-equipment RTR = Ready to Run. The RTR version comes ready to use with the 2,4 GHz rc-system already installed. Transmitter: Reflex Wheel Pro III 2,4 GHzReceiver: Mini BECHigh power servo for throttle and brakeLargescale servo for steeringTx-battery, rx-battery Technical description:The models are built on a 4mm alloy chassis with double wishbones at front and rear axle. All borings of the alloy chassis are countersunk to prevent the screw heads from bearing out. The models are serial equipped with the 2-damper front axle which guarantees an optimal traction of both front wheels. At the front/rear axle you can adjust through track rods or adjusting screws with right-/left-handed thread the king pin angle, trailing effect and toe-in. Further equipment points are front disk brakes, differential gear, easy-running FG ball drive, alloy brake calliper with big brake disk, stabilizer bar front and rear, tuned pipe muffler, Evo gas tank, rear brace, 20T steel pinion, spark plug cap suppression cover, latest version (Evo) oil-pressure shock absorbers with volume control and external adjusting ring for the initial spring preload. All rotating parts as shafts, axles and clutch bells a.s.o. are supported by ball bearings. The models are equipped with a powerful 23 cm³ combustion engine. The engine needs a 2-stroke petrol oil mixture. One tank filling gives you about 45 minutes driving fun. The power is transmitted over the well-tried system: from the engine over the 2-block clutch over radial tooth wheels on to the rear axle which is equipped with the bevel differential gear with pluggable axles. RC-plate with receiver box.Dimensions:Length: 880 mmWidth: 435 mmHeight: 380 mmWheelbase: 530 mmTrucks in action!

€1,199.95*

Average rating of 0 out of 5 stars

5800 Mielke quick fill fuel cap system for FG/ Mecatech tank
Genuine Mielke spare/option part. The quick fill fuel tank cap has a threaded shank to screw it into the filler neck. An O-ring seals the connection. The cap can be turned into the desired position and will be locked there by screws.Fits FG and Mecatech tanks.Contents:1 piece

€54.50*
Loading...
Upload in progress, please be patient ...
Shopware-Agency Shopware-Agency