50353021 Support Blocks for the Lightscale Droop Gauge 35 mm rear, 1 pcs.
Product number:
clarks_50353021
EAN:
4058575032083
Product information "50353021 Support Blocks for the Lightscale Droop Gauge 35 mm rear, 1 pcs."
Item N° 50353021
Support Blocks for the Lightscale Droop Gauge 35 mm rear, 1 pce.
This is an Alloy Support Block anodized in black colour with 35mm height.
The Support Block is manufactured as a rectangle and so can used as a 30mm as well as a 35mm, depending on which side you choose.
The front block uses a single point of support while the rear one comes with two of those. Due to this 3 point support it is assured that even a little tweak in your chassis (none of them is 100% straight) will not affect the result of your measurement.
Remove the wheels and tyres from your car and put the car onto the support blocks. Ideally the rear block is positioned to the back of car and the front one just where the servo saver is fixed to the chassis. The car is now propped on the support blocks safely and cannot bounce. Please make sure that no dirt or rubber is trapped between the Support blocks and the chassis.
Now you can easily and correctly measure the droop of each axle and adjust the cars` tweak.
To do so please use the Lightscale Droop Gauge (50835400)
The use of Lightscales` Droop Gauge Support Blocks prevents incorrect measurements and therefore is absolutely reliable. Measurements which are done using a flat surface where the chassis is resting on, like you would use in the pits are usually incorrect due to a slightly tweaked chassis because dirt underneath the chassis will falsify the measurement and lead to a irregular setup. The use of Support Blocks which are based on 4 support points will result in the same incorrect results and downgrade the performance of your car which is why we 100% recommend the use of our support block because as racers ourselves we know all about the problems you may face.
Support Blocks for the Lightscale Droop Gauge 35 mm rear, 1 pce.
This is an Alloy Support Block anodized in black colour with 35mm height.
The Support Block is manufactured as a rectangle and so can used as a 30mm as well as a 35mm, depending on which side you choose.
The front block uses a single point of support while the rear one comes with two of those. Due to this 3 point support it is assured that even a little tweak in your chassis (none of them is 100% straight) will not affect the result of your measurement.
Remove the wheels and tyres from your car and put the car onto the support blocks. Ideally the rear block is positioned to the back of car and the front one just where the servo saver is fixed to the chassis. The car is now propped on the support blocks safely and cannot bounce. Please make sure that no dirt or rubber is trapped between the Support blocks and the chassis.
Now you can easily and correctly measure the droop of each axle and adjust the cars` tweak.
To do so please use the Lightscale Droop Gauge (50835400)
The use of Lightscales` Droop Gauge Support Blocks prevents incorrect measurements and therefore is absolutely reliable. Measurements which are done using a flat surface where the chassis is resting on, like you would use in the pits are usually incorrect due to a slightly tweaked chassis because dirt underneath the chassis will falsify the measurement and lead to a irregular setup. The use of Support Blocks which are based on 4 support points will result in the same incorrect results and downgrade the performance of your car which is why we 100% recommend the use of our support block because as racers ourselves we know all about the problems you may face.
Login
Alternatives
Item N° 50353011Support Blocks for the Lightscale Droop Gauge front, 1 pce.This is an Alloy Support Block anodized in black colour with 30mm height.The Support Block is manufactured as a rectangle and so can used a 30mm, depending on which side you choose.The front block uses a single point of support while the rear one comes with two of those. Due to this 3 point support it is assured that even a little tweak in your chassis (none of them is 100% straight) will not affect the result of your measurement. Remove the wheels and tyres from your car and put the car onto the support blocks. Ideally the rear block is positioned to the back of car and the front one just where the servo saver is fixed to the chassis. The car is now propped on the support blocks safely and cannot bounce. Please make sure that no dirt or rubber is trapped between the Support blocks and the chassis.Now you can easily and correctly measure the droop of each axle and adjust the cars` tweak.To do so please use the Lightscale Droop Gauge (50835400)The use of Lightscales` Droop Gauge Support Blocks prevents incorrect measurements and therefore is absolutely reliable. Measurements which are done using a flat surface where the chassis is resting on, like you would use in the pits are usually incorrect due to a slightly tweaked chassis because dirt underneath the chassis will falsify the measurement and lead to a irregular setup. The use of Support Blocks which are based on 4 support points will result in the same incorrect results and downgrade the performance of your car which is why we 100% recommend the use of our support block because as racers ourselves we know all about the problems you may face.
Similar products
Genuine FG spare/option part. You can check and adjust the inclination of front and rear wheels with the inclination-goniometer. In connection with the measuring bench you can also check toe-in of the rear axle. Suitable for all FG models and also other makes scale 1:8-1:5.Delivery content is only the inclination - goniometer.Contents:1 piece
Item N° 8539 Measuring bench 740mm - 1pce.Allows a measuring of toe-in and adjusting of both sides the same time without changing the side. For an optimal usw you need 2 . Suitable for all FG models except Formula 1.
The Lightscale Camber Gauge is a black anodised alloy block that features 8 different angled planes in 0.5° steps from 0.5° to 4° on different surfaces.
The gauge is to be layed down beside a tyre for negative camber angles and any 90° part is put on one of the planes an pulled towards the tyre. Doing so you can easily check the camber of your tyres. To check positive camber, just turn around the gauge.
Turning the gauge upside down will make it a 10mm high block to support you measuring the droop of any 1/5, 1/6 and 1/10 scale Electric or nitro car. Those are usually put on 10mm support blocks and beeing measured their droop with a special tool. The Lightscale ride height gauge (50160200) is a droop gauge as well and will do the job for you.
Item N° 8537 Alloy adjusting disk 145mm - 2pcs.With the alloy adjusting disks you can measure and adjust exactly the toe-in and inclination of front and rear axle. Mount the adjusting disks instead of the wheels. Suitable for FG Formula 1, Race-Trucks and Off-Road models.
Item N° 8539/01 Measuring bench 740mm for F1 - 1pce.Allows a measuring of toe-in and adjusting of the rear axle without changing the side. For an optimal usw you need 2 . Only suitable for Formula 1.
Genuine HT spare/option part.Low height design, allows for easy gap measurement and adjustment without damaging the electrodes.Gauge measures spark plug electrode gaps on gap plugs. Ramp style increments on the outside with a .020-.100 inches range.Use an electrode gap of about .030 for best results.Long lasting solid steel alloy.Contents:1 piece
Genuine FG spare/option part.To measure toe-in and to adjust the rear wheels. Only in connection with inclination-goniometer 8540. With this measuring bench you can only measure one side, to measure the second side change the side. Suitable for all FG models except Formula 1.Contents:1 piece
Genuine HT spare/option part. Stainless steel protractor with 200 mm leg for angles up to 180°. Well-suited for measuring of camber or toe--in/toe-out on rc cars.Contents:1 piece
Item N° 50353011Support Blocks for the Lightscale Droop Gauge front, 1 pce.This is an Alloy Support Block anodized in black colour with 30mm height.The Support Block is manufactured as a rectangle and so can used a 30mm, depending on which side you choose.The front block uses a single point of support while the rear one comes with two of those. Due to this 3 point support it is assured that even a little tweak in your chassis (none of them is 100% straight) will not affect the result of your measurement. Remove the wheels and tyres from your car and put the car onto the support blocks. Ideally the rear block is positioned to the back of car and the front one just where the servo saver is fixed to the chassis. The car is now propped on the support blocks safely and cannot bounce. Please make sure that no dirt or rubber is trapped between the Support blocks and the chassis.Now you can easily and correctly measure the droop of each axle and adjust the cars` tweak.To do so please use the Lightscale Droop Gauge (50835400)The use of Lightscales` Droop Gauge Support Blocks prevents incorrect measurements and therefore is absolutely reliable. Measurements which are done using a flat surface where the chassis is resting on, like you would use in the pits are usually incorrect due to a slightly tweaked chassis because dirt underneath the chassis will falsify the measurement and lead to a irregular setup. The use of Support Blocks which are based on 4 support points will result in the same incorrect results and downgrade the performance of your car which is why we 100% recommend the use of our support block because as racers ourselves we know all about the problems you may face.
Genuine HT spare/option part. For the optimal measurement of the chassis.Steel rulers, 150 and 300 mm long.Contents:2 piece
Genuine FG spare/option part. With the alloy adjusting disks you can measure and adjust exactly the toe-in and inclination of front and rear axle. Mount the adjusting disks instead of the wheels. Suitable for FG 1:5 models.Contents:2 pieces
Customers also viewed
Genuine FG spare/option part. Replacement ball driveshaft, medium versionSuitable for BMW M3 GTR, Mercedes C-Class DTM 04, Mercedes CLK-DTM, McLaren GT, Honda Accord, Dogde Viper, Opel V8 and Porsche Carrera GT.Shaft diameter: 6,5mmBall diameter: 12mmLength: 91mmContents:1 piece
Tools and decorative items are for presentation purpose only and not included. Genuine HT spare/option part. Tool bag, extremely rugged tool bag made from reinforced fabric, sewn edge. With 41 flexible attachment loops for various tools with all-round zipper and reinforced handle.Dimensions:Width: 510 mm Height: 275 mmContents:1 piece
Exciting news for the modeling world: Introducing the new 1:5 Supreme V4.With a fresh design and innovative tread patterns for even higher performance. We are thrilled to present the 1:5 Supreme V4 – our revolutionary tire for the world of four-wheeled modeling. The new V4 aims to raise the bar in competitions and cater to the needs of drivers. It features a redesigned tread with new patterns meticulously crafted for enhanced performance. Let’s see its key features: Exceptional Grip: Advanced tread patterns for unparalleled traction on various asphalt conditions. Simplified Driving: Superior control for a smoother and more effective driving experience. Enhanced Durability: Thanks to the new tread design, the tire’s performance remains consistent even in longer sessions. Available in Three Different Compounds. Like all our products, the V4 is available in various compounds to accommodate different asphalt conditions: - Q01 – SuperSoft - Q03 – Soft - Q05 – MediumNote:The harder a tire compound - the longer it lasts, but the more moderate the performance.The softer a tire compound - the better the performance, but the lower the durability.Hint!As a rule, the same tires can be used for front and rear.If the vehicle tends to oversteer, this can be avoided by using a harder front tire!In wet conditions you should use a rain tire which offers maximum grip under these circumstances.With the use of Magic Rain, a tire traction compound, the grip can be further improved.Check your tires after driving! It can happen that a tire starts to detach from the rim, in this case you should glue this spot immediately with our tire repair kit (y0067), otherwise the tire could detach completely from the rim.So find out which tire is the best for you!Dimension:Outside diameter: approx. 116 mmWidth: approx. 65 mmRims: 18 mm square driveContents:2 piece
Item N° 50353011Support Blocks for the Lightscale Droop Gauge front, 1 pce.This is an Alloy Support Block anodized in black colour with 30mm height.The Support Block is manufactured as a rectangle and so can used a 30mm, depending on which side you choose.The front block uses a single point of support while the rear one comes with two of those. Due to this 3 point support it is assured that even a little tweak in your chassis (none of them is 100% straight) will not affect the result of your measurement. Remove the wheels and tyres from your car and put the car onto the support blocks. Ideally the rear block is positioned to the back of car and the front one just where the servo saver is fixed to the chassis. The car is now propped on the support blocks safely and cannot bounce. Please make sure that no dirt or rubber is trapped between the Support blocks and the chassis.Now you can easily and correctly measure the droop of each axle and adjust the cars` tweak.To do so please use the Lightscale Droop Gauge (50835400)The use of Lightscales` Droop Gauge Support Blocks prevents incorrect measurements and therefore is absolutely reliable. Measurements which are done using a flat surface where the chassis is resting on, like you would use in the pits are usually incorrect due to a slightly tweaked chassis because dirt underneath the chassis will falsify the measurement and lead to a irregular setup. The use of Support Blocks which are based on 4 support points will result in the same incorrect results and downgrade the performance of your car which is why we 100% recommend the use of our support block because as racers ourselves we know all about the problems you may face.
%
Ideal work stand with extra wide tripod up to 100 kg. load capacity with excellent stability, even on uneven (!) urface.Specially made support mechanism, individually adjustable width from 115 mm to 375 mm for most RC cars from 1/10 to 1/5 scale. incline from 0 to 90° Quickly folded and loaded For easy storage, as well as for transport completely foldable! (Carrying bag available!)Height adjustment of the support from 635 mm to 1000 mm and inclination from 0-90° Length of the support surface 386 mm Bis zu 100Kg belastbar! Support mechanism continuosly adjustable in width Due to various adjustment options, the Top Tuning CAR STAND offers the optimal possibilities for making adjustments or maintenance work on the RC car. The load capacity and stability are beyond doubt with a load limit of 100 kg and the extremely stable tripod. The up to 90 ° adjustable slant shows your RC car at events and presentations, as well as in your assembly room to its best advantage! 6.5 kg. weight Pivoting bracket Height adjustable from 69 to 104 cm Basic frame is made of steel, painted or chromed Car bracket is made of aluminum and stainless steel A tool holder TT1030/01 is also available as an accessory in our shop selection.