8541 FG Measuring bench 390 mm

€65.00*

Prices incl. VAT plus shipping costs

Available

Product number: fg_8541

EAN: 3410564523179

Product information "8541 FG Measuring bench 390 mm"

Genuine FG spare/option part.

To measure toe-in and to adjust the rear wheels. Only in connection with inclination-goniometer 8540. With this measuring bench you can only measure one side, to measure the second side change the side.

Suitable for all FG models except Formula 1.

Contents:

1 piece

0 of 0 reviews

Leave a review!

Share your experiences with other customers.

Login

Your email address

Your password

No reviews found. Share your insights with others.

Accessories / Spare parts

8540 FG Inclination-goniometer

Genuine FG spare/option part. You can check and adjust the inclination of front and rear wheels with the inclination-goniometer. In connection with the measuring bench you can also check toe-in of the rear axle. Suitable for all FG models and also other makes scale 1:8-1:5.Delivery content is only the inclination - goniometer.Contents:1 piece

€29.90*

8536 FG Alloy adjusting disk 125 mm

Genuine FG spare/option part. With the alloy adjusting disks you can measure and adjust exactly the toe-in and inclination of front and rear axle. Mount the adjusting disks instead of the wheels. Suitable for FG 1:5 models.Contents:2 pieces

€118.95*

8537 FG Alloy adjusting disk 145mm - 2pcs.

Item N° 8537 Alloy adjusting disk 145mm - 2pcs.With the alloy adjusting disks you can measure and adjust exactly the toe-in and inclination of front and rear axle. Mount the adjusting disks instead of the wheels. Suitable for FG Formula 1, Race-Trucks and Off-Road models.

€118.95*

Alternatives

8539 FG Measuring bench 740mm - 1pce.

Item N° 8539 Measuring bench 740mm - 1pce.Allows a measuring of toe-in and adjusting of both sides the same time without changing the side. For an optimal usw you need 2 . Suitable for all FG models except Formula 1.

€67.95*

8539/01 FG Measuring bench 740mm for F1 - 1pce.

Item N° 8539/01 Measuring bench 740mm for F1 - 1pce.Allows a measuring of toe-in and adjusting of the rear axle without changing the side. For an optimal usw you need 2 . Only suitable for Formula 1.

€67.95*

This product is currently not available.

8541/01 FG Measuring bench 390mm for F1 - 1pce.

Item N° 8541/01 Measuring bench 390mm for F1 - 1pce.To measure toe-in and to adjust the track width of the rear axle, only in connection with inclination-goniometer . With this measuring bench one side can be measured, to measure the second side you have to change the side. Suitable only for Formula 1.

€65.00*

Similar products

8539/01 FG Measuring bench 740mm for F1 - 1pce.

€67.95*

This product is currently not available.

y1489 spark plug gap tool

Genuine HT spare/option part.Low height design, allows for easy gap measurement and adjustment without damaging the electrodes.Gauge measures spark plug electrode gaps on gap plugs. Ramp style increments on the outside with a .020-.100 inches range.Use an electrode gap of about .030 for best results.Long lasting solid steel alloy.Contents:1 piece

€4.90*

8537 FG Alloy adjusting disk 145mm - 2pcs.

€118.95*

8539 FG Measuring bench 740mm - 1pce.

€67.95*

LOSA99172 Camber Gauge

Genuine Losi spare/option part. Contents:1 piece

€19.99*

Details

50353021 Support Blocks for the Lightscale Droop Gauge 35 mm rear, 1 pcs.

Item N° 50353021Support Blocks for the Lightscale Droop Gauge 35 mm rear, 1 pce.This is an Alloy Support Block anodized in black colour with 35mm height.The Support Block is manufactured as a rectangle and so can used as a 30mm as well as a 35mm, depending on which side you choose.The front block uses a single point of support while the rear one comes with two of those. Due to this 3 point support it is assured that even a little tweak in your chassis (none of them is 100% straight) will not affect the result of your measurement. Remove the wheels and tyres from your car and put the car onto the support blocks. Ideally the rear block is positioned to the back of car and the front one just where the servo saver is fixed to the chassis. The car is now propped on the support blocks safely and cannot bounce. Please make sure that no dirt or rubber is trapped between the Support blocks and the chassis.Now you can easily and correctly measure the droop of each axle and adjust the cars` tweak.To do so please use the Lightscale Droop Gauge (50835400)The use of Lightscales` Droop Gauge Support Blocks prevents incorrect measurements and therefore is absolutely reliable. Measurements which are done using a flat surface where the chassis is resting on, like you would use in the pits are usually incorrect due to a slightly tweaked chassis because dirt underneath the chassis will falsify the measurement and lead to a irregular setup. The use of Support Blocks which are based on 4 support points will result in the same incorrect results and downgrade the performance of your car which is why we 100% recommend the use of our support block because as racers ourselves we know all about the problems you may face.

€29.90*

50040050 Lightscale alloy rebound gauge, black, 1 pce.

The Lightscale Camber Gauge is a black anodised alloy block that features 8 different angled planes in 0.5° steps from 0.5° to 4° on different surfaces. The gauge is to be layed down beside a tyre for negative camber angles and any 90° part is put on one of the planes an pulled towards the tyre. Doing so you can easily check the camber of your tyres. To check positive camber, just turn around the gauge. Turning the gauge upside down will make it a 10mm high block to support you measuring the droop of any 1/5, 1/6 and 1/10 scale Electric or nitro car. Those are usually put on 10mm support blocks and beeing measured their droop with a special tool. The Lightscale ride height gauge (50160200) is a droop gauge as well and will do the job for you.

€27.90*

y1450 Steel protractor

Genuine HT spare/option part. Stainless steel protractor with 200 mm leg for angles up to 180°. Well-suited for measuring of camber or toe--in/toe-out on rc cars.Contents:1 piece

€9.90*

8540 FG Inclination-goniometer

€29.90*

50353011 Support Blocks for the Lightscale Droop Gauge front 30 mm, 1 pce.

Item N° 50353011Support Blocks for the Lightscale Droop Gauge front, 1 pce.This is an Alloy Support Block anodized in black colour with 30mm height.The Support Block is manufactured as a rectangle and so can used a 30mm, depending on which side you choose.The front block uses a single point of support while the rear one comes with two of those. Due to this 3 point support it is assured that even a little tweak in your chassis (none of them is 100% straight) will not affect the result of your measurement. Remove the wheels and tyres from your car and put the car onto the support blocks. Ideally the rear block is positioned to the back of car and the front one just where the servo saver is fixed to the chassis. The car is now propped on the support blocks safely and cannot bounce. Please make sure that no dirt or rubber is trapped between the Support blocks and the chassis.Now you can easily and correctly measure the droop of each axle and adjust the cars` tweak.To do so please use the Lightscale Droop Gauge (50835400)The use of Lightscales` Droop Gauge Support Blocks prevents incorrect measurements and therefore is absolutely reliable. Measurements which are done using a flat surface where the chassis is resting on, like you would use in the pits are usually incorrect due to a slightly tweaked chassis because dirt underneath the chassis will falsify the measurement and lead to a irregular setup. The use of Support Blocks which are based on 4 support points will result in the same incorrect results and downgrade the performance of your car which is why we 100% recommend the use of our support block because as racers ourselves we know all about the problems you may face.

€24.90*

FG aluminium adjusting disc 125 mm, set of 4 pieces

Original FG spare/tuning part. The toe-in and camber settings of the front and rear axles can be precisely measured and adjusted using the aluminium adjusting screws. The adjusting discs are fitted instead of the wheels. - Suitable for FG 1:5 models. - 2 pairs. - See photos for features and condition. - As good as new.

€59.00* €237.90* (75.2% saved)

8536 FG Alloy adjusting disk 125 mm

€118.95*