Skip to main content Skip to search Skip to main navigation
+49 2151 820200
Mon-Fri 9 am - 6 pm, Sa 9 am - 1 pm
Fast shipping until 1 p.m.

50353011 Support Blocks for the Lightscale Droop Gauge front 30 mm, 1 pce.

Product information "50353011 Support Blocks for the Lightscale Droop Gauge front 30 mm, 1 pce."

Item N° 50353011
Support Blocks for the Lightscale Droop Gauge front, 1 pce.


This is an Alloy Support Block anodized in black colour with 30mm height.
The Support Block is manufactured as a rectangle and so can used a 30mm, depending on which side you choose.
The front block uses a single point of support while the rear one comes with two of those. Due to this 3 point support it is assured that even a little tweak in your chassis (none of them is 100% straight) will not affect the result of your measurement.

Remove the wheels and tyres from your car and put the car onto the support blocks. Ideally the rear block is positioned to the back of car and the front one just where the servo saver is fixed to the chassis. The car is now propped on the support blocks safely and cannot bounce. Please make sure that no dirt or rubber is trapped between the Support blocks and the chassis.
Now you can easily and correctly measure the droop of each axle and adjust the cars` tweak.
To do so please use the Lightscale Droop Gauge (50835400)

The use of Lightscales` Droop Gauge Support Blocks prevents incorrect measurements and therefore is absolutely reliable. Measurements which are done using a flat surface where the chassis is resting on, like you would use in the pits are usually incorrect due to a slightly tweaked chassis because dirt underneath the chassis will falsify the measurement and lead to a irregular setup. The use of Support Blocks which are based on 4 support points will result in the same incorrect results and downgrade the performance of your car which is why we 100% recommend the use of our support block because as racers ourselves we know all about the problems you may face.

0 of 0 reviews

Average rating of 0 out of 5 stars

Leave a review!

Share your experiences with other customers.


Skip product gallery

Customers also viewed

50040050 Lightscale alloy rebound gauge, black, 1 pce.
50040050 Lightscale alloy rebound gauge, black, 1 pce.

The Lightscale Camber Gauge is a black anodised alloy block that features 8  different angled planes in 0.5° steps from 0.5° to 4° on different surfaces.
The gauge is to be layed down beside a tyre for negative camber angles and any 90° part is put on one of the planes an pulled towards the tyre. Doing so you can easily check the camber of your tyres. To check positive camber, just turn around the gauge.
Turning the gauge upside down will make it a 10mm high block to support you measuring the droop of any 1/5, 1/6 and 1/10 scale Electric or nitro car. Those are usually put on 10mm support blocks and beeing measured their droop with a special tool. The Lightscale ride height gauge (50160200) is a droop gauge as well and will do the job for you.

Regular price: €24.90
%
G002 Carson Multi-function wrench
G002 Carson Multi-function wrench

Genuine Carson spare/option part. Contents:1 piece

Sale price: €11.45 Regular price: €22.90 (50% saved)
8539 FG Measuring bench 740mm - 1pce.
8539 FG Measuring bench 740mm - 1pce.

Item N° 8539 Measuring bench 740mm - 1pce.Allows a measuring of toe-in and adjusting of both sides the same time without changing the side. For an optimal usw you need 2 . Suitable for all FG models except Formula 1.

Regular price: €67.95
8537 FG Alloy adjusting disk 145mm - 2pcs.
8537 FG Alloy adjusting disk 145mm - 2pcs.

Item N° 8537 Alloy adjusting disk 145mm - 2pcs.With the alloy adjusting disks you can measure and adjust exactly the toe-in and inclination of front and rear axle. Mount the adjusting disks instead of the wheels. Suitable for FG Formula 1, Race-Trucks and Off-Road models.

Regular price: €115.50
8540 FG Inclination-goniometer
8540 FG Inclination-goniometer

Genuine FG spare/option part. You can check and adjust the inclination of front and rear wheels with the inclination-goniometer. In connection with the measuring bench you can also check toe-in of the rear axle. Suitable for all FG models and also other makes scale 1:8-1:5.Delivery content is only the inclination - goniometer.Contents:1 piece

Regular price: €31.90
y1524 Complete screws/nuts/washers set for HPI Baja / Carson 1:5 Wild GP Attack
y1524 Complete screws/nuts/washers set for HPI Baja / Carson 1:5 Wild GP Attack

Complete set of screws, nuts and washers for HPI Baja 1/5 vehicles.The set includes a total of 434 screws, nuts and washers in different quantities which are all used on HPI Baja 1/5 vehicles and Carson 1:5 Wild GP Attack.11 sizes of cap head screws9 sizes of CSH screws10 sizes of button head screws4 sizes of set screws2 sizes of washers3 sizes of lock washers3 sizes of self-locking nuts2 sizes of nuts with serrated flange2 sizes of flanged self tapping screwsComes in a high quality 190x170x40 mm assortment box.Contents:Cap head screws in 12.9:20 piecesM3x126 piecesM3x4510 piecesM4x612 piecesM4x1212 piecesM4x2510 piecesM4x306 piecesM4x507 piecesM5x206 piecesM5x306 piecesM5x356 piecesM6x25CSH screws in 10.9:10 piecesM3x2010 piecesM4x1019 piecesM5x1616 piecesM5x206 piecesM5x302 piecesM5x407 piecesM6x14Button head screws in 10.94 piecesM3x1610 piecesM3x303 piecesM4x166 piecesM5x123 piecesM5x302 piecesM5x356 piecesM5x406 piecesM5x452 piecesM6x306 piecesM6x30Grub screws:6 piecesM3x39 piecesM4x46 piecesM4x124 piecesM6x45Washers in Din125:10 pieces3,2x6,8x0,512 pieces4,3x8,7x0,8Safety washers:20 piecesM420 piecesM520 piecesM6Self-locking nuts:10 piecesM310 piecesM415 piecesM5Flanged nuts with serrated base:21 piecesM410 piecesM5CSH screws Torx:10 piecesM4x15 (4,2x16)10 piecesM4x18 (4,2x19)Schneidschrauben Torx mit flanged:10 piecesM2,6x1012 piecesM3x10

Regular price: €49.90
Loading...
Upload in progress, please be patient ...