8537 FG Alloy adjusting disk 145mm - 2pcs.

Item N° 8539/01 Measuring bench 740mm for F1 - 1pce.Allows a measuring of toe-in and adjusting of the rear axle without changing the side. For an optimal usw you need 2 . Only suitable for Formula 1.

Genuine HT spare/option part.Low height design, allows for easy gap measurement and adjustment without damaging the electrodes.Gauge measures spark plug electrode gaps on gap plugs. Ramp style increments on the outside with a .020-.100 inches range.Use an electrode gap of about .030 for best results.Long lasting solid steel alloy.Contents:1 piece

Item N° 8539 Measuring bench 740mm - 1pce.Allows a measuring of toe-in and adjusting of both sides the same time without changing the side. For an optimal usw you need 2 . Suitable for all FG models except Formula 1.

Genuine Losi spare/option part. Contents:1 piece

Genuine FG spare/option part.To measure toe-in and to adjust the rear wheels. Only in connection with inclination-goniometer 8540. With this measuring bench you can only measure one side, to measure the second side change the side. Suitable for all FG models except Formula 1.Contents:1 piece

Item N° 50353021Support Blocks for the Lightscale Droop Gauge 35 mm rear, 1 pce.This is an Alloy Support Block anodized in black colour with 35mm height.The Support Block is manufactured as a rectangle and so can used as a 30mm as well as a 35mm, depending on which side you choose.The front block uses a single point of support while the rear one comes with two of those. Due to this 3 point support it is assured that even a little tweak in your chassis (none of them is 100% straight) will not affect the result of your measurement. Remove the wheels and tyres from your car and put the car onto the support blocks. Ideally the rear block is positioned to the back of car and the front one just where the servo saver is fixed to the chassis. The car is now propped on the support blocks safely and cannot bounce. Please make sure that no dirt or rubber is trapped between the Support blocks and the chassis.Now you can easily and correctly measure the droop of each axle and adjust the cars` tweak.To do so please use the Lightscale Droop Gauge (50835400)The use of Lightscales` Droop Gauge Support Blocks prevents incorrect measurements and therefore is absolutely reliable. Measurements which are done using a flat surface where the chassis is resting on, like you would use in the pits are usually incorrect due to a slightly tweaked chassis because dirt underneath the chassis will falsify the measurement and lead to a irregular setup. The use of Support Blocks which are based on 4 support points will result in the same incorrect results and downgrade the performance of your car which is why we 100% recommend the use of our support block because as racers ourselves we know all about the problems you may face.

The Lightscale Camber Gauge is a black anodised alloy block that features 8  different angled planes in 0.5° steps from 0.5° to 4° on different surfaces.
The gauge is to be layed down beside a tyre for negative camber angles and any 90° part is put on one of the planes an pulled towards the tyre. Doing so you can easily check the camber of your tyres. To check positive camber, just turn around the gauge.
Turning the gauge upside down will make it a 10mm high block to support you measuring the droop of any 1/5, 1/6 and 1/10 scale Electric or nitro car. Those are usually put on 10mm support blocks and beeing measured their droop with a special tool. The Lightscale ride height gauge (50160200) is a droop gauge as well and will do the job for you.

Genuine HT spare/option part. Stainless steel protractor with 200 mm leg for angles up to 180°. Well-suited for measuring of camber or toe--in/toe-out on rc cars.Contents:1 piece

Genuine FG spare/option part. You can check and adjust the inclination of front and rear wheels with the inclination-goniometer. In connection with the measuring bench you can also check toe-in of the rear axle. Suitable for all FG models and also other makes scale 1:8-1:5.Delivery content is only the inclination - goniometer.Contents:1 piece

Item N° 50353011Support Blocks for the Lightscale Droop Gauge front, 1 pce.This is an Alloy Support Block anodized in black colour with 30mm height.The Support Block is manufactured as a rectangle and so can used a 30mm, depending on which side you choose.The front block uses a single point of support while the rear one comes with two of those. Due to this 3 point support it is assured that even a little tweak in your chassis (none of them is 100% straight) will not affect the result of your measurement. Remove the wheels and tyres from your car and put the car onto the support blocks. Ideally the rear block is positioned to the back of car and the front one just where the servo saver is fixed to the chassis. The car is now propped on the support blocks safely and cannot bounce. Please make sure that no dirt or rubber is trapped between the Support blocks and the chassis.Now you can easily and correctly measure the droop of each axle and adjust the cars` tweak.To do so please use the Lightscale Droop Gauge (50835400)The use of Lightscales` Droop Gauge Support Blocks prevents incorrect measurements and therefore is absolutely reliable. Measurements which are done using a flat surface where the chassis is resting on, like you would use in the pits are usually incorrect due to a slightly tweaked chassis because dirt underneath the chassis will falsify the measurement and lead to a irregular setup. The use of Support Blocks which are based on 4 support points will result in the same incorrect results and downgrade the performance of your car which is why we 100% recommend the use of our support block because as racers ourselves we know all about the problems you may face.

Original FG spare/tuning part. The toe-in and camber settings of the front and rear axles can be precisely measured and adjusted using the aluminium adjusting screws. The adjusting discs are fitted instead of the wheels.  - Suitable for FG 1:5 models. - 2 pairs. - See photos for features and condition. - As good as new.

Genuine FG spare/option part. With the alloy adjusting disks you can measure and adjust exactly the toe-in and inclination of front and rear axle. Mount the adjusting disks instead of the wheels. Suitable for FG 1:5 models.Contents:2 pieces

Item N° 8539 Measuring bench 740mm - 1pce.Allows a measuring of toe-in and adjusting of both sides the same time without changing the side. For an optimal usw you need 2 . Suitable for all FG models except Formula 1.

Genuine FG spare/option part. These cask-shaped shock springs are suitable for the shocks from the EVO 2020 and other shocks with an outer body diameter of 20 mm.Wire diameter. 2.4 mmContents:2 pieces

Go BIG wherever you bash with the 1/6 scale Losi® Super Rock Rey® AVC® 4WD! This ready-to-run gives any driver the power and stability to succeed off the beaten path and to dominate the desert with impressive size, speed, and endurance.The Super Rock Rey® takes its inspiration from full-scale rigs that tackle the King of Hammers and similar places others wont dare go. Realistic solid axle performance joins 6S brushless power that pushes the needle to 50+ mph or more while the stability of AVC® technology lets you hold nothing back through corners and jumps.Over rough terrain, slick surfaces, and loose dirt, youll have full-throttle freedom no matter how the environment fights back. Dependable Spektrum DSMR® technology delivers precise control. Through it all, the bottom-loading battery enables fast pack changes without body removal.The large tires and new front end geometry increase suspension travel and improve performance over any terrain. Super Rock Rey loves rocky off-road tracks, and the rougher, the better! It also rips through sand, mud, water, and most any other surface condition with a new roll cage and body work creating the dirt-spitting image of 1:1 desert racing, rock crawling, off-road action.Impressive 1/6 scale size and exceptional scale looks.55+ mph speed potential to outperform the competition.Supports up to 6S LiPo battery power out of the box.AVC® Active Vehicle Control system to provide the right amount of stability for any driver.4WD independent front suspension with solid axle 4-link rear adds realism and improves performance over any terrain.4mm aluminum chassis with injection-molded roll cage provides superior durability and scale looks.Larger wheels and tires increase ground clearance to avoid hang-ups.LED light bars provide scale looks when the sun goes down.All-metal gear drivetrain increases durability.Preset motor plate provides easy, precise gear mesh.Coil-over, oil-filled shocks keep the ride smooth and plush.750Kv Dynamite® Brushless Motor and Dynamite Fuze 160A Brushless ESC are capable of 6S up to 8S power and 50+ mph speeds.Waterproof electronics withstand racing over wet and muddy tracks.Spektrum DX2E Active 2.4GHz Radio SystemLarge-scale, metal gear Spektrum steering servo withstands punishing action.Multi-piece body and driver interior maximize scale realism.Bottom-loading battery makes pack changes quick and easy, with the capacity to hold up to 6S packs.Ball Bearings: Full Ball BearingsChassis: 4mm Plate, 6061-T6 AluminumCompletion Level: Ready-To-RunDifferential: Fluid Filled, Bevel GearGear Pitch: 1.5 ModuleGround Clearance: 3.0 in (76.2 mm)Internal Gear Ratio: 4.88:1Motor Type: Non-Sensored BrushlessRadio: Spektrum DX2E Active, 2 ch DSMR with AVCShock Type: Oil-Filled, Coil-Over SpringsSuspension: Independent Front/4-Link RearVehicle Type: Off-Road Rock Racing BuggyWater-Resistant: YesDimensions:Motor Size: 56 x 87 mmLength: 27.0 in (685.8 mm)Weight: 20.6 lb (9.3 kg) without batteriesWheel Diameter: 3.2 in (81.3 mm)Wheel Width: 2.1 in (53.3 mm)Wheelbase: 20.0 in (508.0 mm)Width: 17.25 in (438.1 mm)Front Track: 17.25 in (438.1 mm)Rear Track: 16.5 in (419.1 mm)Height: 11.0 in (279.4 mm)Tire Diameter: 7.0 in (177.8 mm) Long Travel 4-link Live Rear Axle The Super Rock Reys rear suspension allows it to soak up massive whoops and bumps with the same realistic handling and movement of a full-scale desert truck. You get better control and a more locked-in feel regardless of the terrain. Long Travel Independent A-Arm Front Suspension The front, independent A-Arm suspension has been carefully engineered letting the Super Rock Rey rip across the terrain with confidence. By having fully independent suspension, it allows each side to react accordingly providing more control and more precise steering and handling. Coil-Over Oil Filled Shocks with Pre-Load adjustment The long-travel shocks do a fantastic job of soaking up the energy from big bumps and jumps. They also feature threaded shock bodies with adjustment collars so you can fine tune the pre-load settings of the coil-over springs. External bump stops provide plush landings on the hardest surfaces. 55+ MPH Dynamite Fuze 1/6th 750Kv Brushless Motor and 160A ESC The vehicle comes equipped with a Dynamite® Fuze 750Kv brushless motor and a waterproof 160A ESC. This potent combination can handle 8S LiPo batteries (sold separately) and will allow you to hurtle across the landscape at speeds of up to 55+ mph. Full Bodied Roll Cage Just like the 1:1 desert trucks, the Super Rock Rey® truck comes with a super-rigid roll cage made of super-tough composite material that enhances the trucks scale looks and durability. It is integrated with the 4mm hard-anodized aluminum chassis plate providing the ultimate protection for your truck and electronics. True-to-Scale Body Panels The two piece bolt-on body panels give the buggy an authentic factory look. These panels are polycarbonate for incredible durability and rugged good looks. Aluminum Chassis The foundation of the Super Rock Rey consists of a 4mm, hard-anodized aluminum chassis plate with a 4mm upper deck. For added durability and performance its integrated with a realistic roll cage made of super-tough composite material. Whether you are hitting the whoops, getting huge air, or just wide open, the 4mm chassis just keeps asking for more! 4X4 Driveline with Adjustable Differentials Full-time four-wheel drive provides amazing traction. Additionally the front, center and rear differentials can be tuned allowing adjustment of the power bleed between the front and rear drivetrain. The power bleeds evenly front-to-rear and the truck will drive out of the turns harder from point to point. The tunable differentials allow you to dial in your truck for maximum performance and traction. LED Light Bars (Front) The fun doesnt stop even when the sun goes down with the Super Rock Rey. Brilliant LEDs on the two front-mounted integrated light bar cast more than enough illumination for running at night. Plus, the roll cage-mounted LEDs place only a small demand on the battery allowing you to stay out all night! LED Light Bars (Rear) Just as important as the front lights, the red rear lights allow you to gauge the orientation of the buggy even in the darkest night. Large Scale Servo The robust Spektrum S904 waterproof digital servo is designed to handle whatever you can throw at it. Monstrous torque delivers the most intense Super Rock Rey® experience possible. Bottom-Loading-Batterie To help withstand the trials and tribulations of off-road driving, the Super Rock Rey incorporates our innovative bottom loading battery system, which allows you to change the batteries without removing the body. Quickly and easily make battery changes without removing the body or wrestling with battery straps. Full-Size Spare Tire Blow out a tire out on the flats? No worries. The fully-functional spare tire not only adds an authentic scale look to the Super Rock Rey®, but serves as a true spare. Easily add the tire and get back to tackling the terrain. Scale Fox Shox Looking just like their full-scale counterparts, the Fox Shox reservoirs add to the incredible scale realism of the Super Rock Rey. Scale Fire Extinguisher The Super Rock Rey features several scale details rarely included. Attached to the outside, the scale fire extinguisher is at the ready and adds to the realism of this desert racer. Scale Rear View Mirrors Scale rear view mirrors on the Super Rock Reys doors include high-end details like mirror-like chrome inserts. You can actually see your reflection! Scale Window Netting Rubberized safety window netting looks and feels like the full-scale counterparts real netting. Everywhere you look, the Super Rock Reys scale details set it apart from the competition. Fully Detailed Driver Figures The Super Rock Rey also has a molded interior that includes a driver and co-driver, both of which sport racing helmet and harness details. Suspension Limiting Straps Fully-functional suspension limiting straps look and act just like their real-world counterparts. A buckle allows drivers to adjust the length of the strap. Scale Appearing Rotors and Calipers Mounted separately, the authentic looking rotors and calipers add to the incredible scale appearance and keep the realism alive as the Super Rock Rey races over rough terrain. Authentic MAXXIS Creeper Crawler Tires True-to-scale tires look incredible, increase ground clearance to avoid hang-ups, and allow drivers to hit the ground running. Licensed Trim Schemes Licensed Raceline Wheels and Baja Designs trim schemes complete the scale details of the Super Rock Rey. These trim schemes will have racers doing double takes as they take on all comers. Spektrum DX2E Active Radio System The Spektrum DX2e Active radio system offers advanced features like AVC control, a 3-position throttle limiting switch and travel adjust. It also has an expansion port that lets you add the Spektrum Speedometer or a Bluetooth module and phone mount to utilize the Spektrum Dashboard app. The Full-Throttle Freedom of AVC® Technology The receiver"s built-in AVC® (Active Vehicle Control®) system works behind the scenes, making hundreds of throttle and steering adjustments per second, so more of the motor"s power is translated into ballistic speed and acceleration instead of just flying dirt. The patent-pending AVC system adds a level of performance that simply cannot be found with any vehicle from any manufacturer other than Horizon Hobby. Like traction control in your full-scale vehicle, you can activate or deactivate the system on the fly and adjust the level of stability based on driving conditions. Any RC vehicle can go fast and with AVC you can go faster while maintaining optimum stability in all driving conditions. It is still needed:Charger

The sets include:Item N°Name:y1027HT Aluminum a-arm 2WD, front uppery1026HT Aluminum a-arm 2WD, front lower, one-piecey1028HT Aluminum front bulkhead A for 2WDy1030HT Aluminum front bulkhead B for 2WDy1036HT rose joints with conical spacersy1029HT aluminum droop stopsy1032HT Aluminum shock tower Marder 2WDy1031HT Aluminum bulkhead brace for 2WDUnit prices: 391,00 EURThe sets include complete front bulkheads A + B with brace, upper (adjustable) and lower a-arms and shock tower.Please note: the hinge pins are not included, you will use the pins from the stock suspension!Fits FG Marder, Beetle, Pajero and Monster Beetle.

Genuine FG spare/option part. You can check and adjust the inclination of front and rear wheels with the inclination-goniometer. In connection with the measuring bench you can also check toe-in of the rear axle. Suitable for all FG models and also other makes scale 1:8-1:5.Delivery content is only the inclination - goniometer.Contents:1 piece

Genuine HT spare/option part. Ball & socket tool with t-handle, especially for installation and removal of balls in FG or Smartech/Carson cars' plastic a-arms and steering rod ball joints.Contents:1 piece

Small steel modul (1,25) transmission set for Sportsline and Challenge Line, improves performance and reliability.