8539 FG Measuring bench 740mm - 1pce.

Genuine Losi spare/option part. Contents:1 piece

Genuine HT spare/option part.Low height design, allows for easy gap measurement and adjustment without damaging the electrodes.Gauge measures spark plug electrode gaps on gap plugs. Ramp style increments on the outside with a .020-.100 inches range.Use an electrode gap of about .030 for best results.Long lasting solid steel alloy.Contents:1 piece

Genuine FG spare/option part. You can check and adjust the inclination of front and rear wheels with the inclination-goniometer. In connection with the measuring bench you can also check toe-in of the rear axle. Suitable for all FG models and also other makes scale 1:8-1:5.Delivery content is only the inclination - goniometer.Contents:1 piece

The Lightscale Camber Gauge is a black anodised alloy block that features 8  different angled planes in 0.5° steps from 0.5° to 4° on different surfaces.
The gauge is to be layed down beside a tyre for negative camber angles and any 90° part is put on one of the planes an pulled towards the tyre. Doing so you can easily check the camber of your tyres. To check positive camber, just turn around the gauge.
Turning the gauge upside down will make it a 10mm high block to support you measuring the droop of any 1/5, 1/6 and 1/10 scale Electric or nitro car. Those are usually put on 10mm support blocks and beeing measured their droop with a special tool. The Lightscale ride height gauge (50160200) is a droop gauge as well and will do the job for you.

Item N° 8537 Alloy adjusting disk 145mm - 2pcs.With the alloy adjusting disks you can measure and adjust exactly the toe-in and inclination of front and rear axle. Mount the adjusting disks instead of the wheels. Suitable for FG Formula 1, Race-Trucks and Off-Road models.

Genuine HT spare/option part. For the optimal measurement of the chassis.Steel rulers, 150 and 300 mm long.Contents:2 piece

Item N° 8539/01 Measuring bench 740mm for F1 - 1pce.Allows a measuring of toe-in and adjusting of the rear axle without changing the side. For an optimal usw you need 2 . Only suitable for Formula 1.

Genuine FG spare/option part.To measure toe-in and to adjust the rear wheels. Only in connection with inclination-goniometer 8540. With this measuring bench you can only measure one side, to measure the second side change the side. Suitable for all FG models except Formula 1.Contents:1 piece

Genuine FG spare/option part. With the alloy adjusting disks you can measure and adjust exactly the toe-in and inclination of front and rear axle. Mount the adjusting disks instead of the wheels. Suitable for FG 1:5 models.Contents:2 pieces

Item N° 50353011Support Blocks for the Lightscale Droop Gauge front, 1 pce.This is an Alloy Support Block anodized in black colour with 30mm height.The Support Block is manufactured as a rectangle and so can used a 30mm, depending on which side you choose.The front block uses a single point of support while the rear one comes with two of those. Due to this 3 point support it is assured that even a little tweak in your chassis (none of them is 100% straight) will not affect the result of your measurement. Remove the wheels and tyres from your car and put the car onto the support blocks. Ideally the rear block is positioned to the back of car and the front one just where the servo saver is fixed to the chassis. The car is now propped on the support blocks safely and cannot bounce. Please make sure that no dirt or rubber is trapped between the Support blocks and the chassis.Now you can easily and correctly measure the droop of each axle and adjust the cars` tweak.To do so please use the Lightscale Droop Gauge (50835400)The use of Lightscales` Droop Gauge Support Blocks prevents incorrect measurements and therefore is absolutely reliable. Measurements which are done using a flat surface where the chassis is resting on, like you would use in the pits are usually incorrect due to a slightly tweaked chassis because dirt underneath the chassis will falsify the measurement and lead to a irregular setup. The use of Support Blocks which are based on 4 support points will result in the same incorrect results and downgrade the performance of your car which is why we 100% recommend the use of our support block because as racers ourselves we know all about the problems you may face.

Genuine HT spare/option part. Stainless steel protractor with 200 mm leg for angles up to 180°. Well-suited for measuring of camber or toe--in/toe-out on rc cars.Contents:1 piece

Item N° 8541/01 Measuring bench 390mm for F1 - 1pce.To measure toe-in and to adjust the track width of the rear axle, only in connection with inclination-goniometer . With this measuring bench one side can be measured, to measure the second side you have to change the side. Suitable only for Formula 1.

Item N° 8537 Alloy adjusting disk 145mm - 2pcs.With the alloy adjusting disks you can measure and adjust exactly the toe-in and inclination of front and rear axle. Mount the adjusting disks instead of the wheels. Suitable for FG Formula 1, Race-Trucks and Off-Road models.

Genuine FG spare/option part. With the alloy adjusting disks you can measure and adjust exactly the toe-in and inclination of front and rear axle. Mount the adjusting disks instead of the wheels. Suitable for FG 1:5 models.Contents:2 pieces

Genuine FG spare/option part.To measure toe-in and to adjust the rear wheels. Only in connection with inclination-goniometer 8540. With this measuring bench you can only measure one side, to measure the second side change the side. Suitable for all FG models except Formula 1.Contents:1 piece

y0557 Zenoah G230RC, with Walbro WT 603B carburetor (also available in the ball-raced version through the shop's options menu)23 cm³ Zenoah engine for large scale cars!The engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter and / or complete clutch are optionally available at additional charge.y1009 Zenoah G240RC with Walbro WT 990 carburetor (also available in the ball-raced version through the shop's options menu)23 cm³ Zenoah engine for large scale cars!Please note: contrary to their new designation the displacement has not been increased! The outer dimension didn't change, so you don't need any additional parts for the engine swap!The engines feature the following improvements over their G230RC:- Quantity of cylinder mounting bolts increased from 2 to 4- Improved strength of crankcase- Added additional bearing on the PTO (clutch) side of crankshaft- Redesigned shape of cylinder fins- Dimension of air intake port is 5% widerContains internal fuel pump which increases acceleration from idle to wide open throttle.Removal of choke valve increases performance by increasing air flow to the carburetor - Changed material of the insulator gasket to metal, which improves sealing performanceThe engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter and / or complete clutch are optionally available at additional charge. y0553 Zenoah G260RC with Walbro WT 603B carburetor (also available in the ball-raced version through the shop's options menu)This is the G260 in the 26 cm³ version.The engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter and / or complete clutch are optionally available at additional charge. y1011 Zenoah G270RC with Walbro WT 990 carburetor (also available in the ball-raced version through the shop's options menu)26 cm³ Zenoah engine for large scale cars!Please note: contrary to their new designation the displacement has not been increased! The outer dimension didn't change, so you don't need any additional parts for the engine swap!The engines feature the following improvements over their G260RC:- Quantity of cylinder mounting bolts increased from 2 to 4- Improved strength of crankcase- Added additional bearing on the PTO (clutch) side of crankshaft- Redesigned shape of cylinder fins- Dimension of air intake port is 5% wider- New carburetor (WT-990) Contains internal fuel pump which increases acceleration from idle to wide open throttle.Removal of choke valve increases performance by increasing air flow to the carburetor - Changed material of the insulator gasket to metal, which improves sealing performanceThe engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter are optionally available at additional charge. 7800 Zenoah G290RC with Walbro WT 990 carburetor (also available in the ball-raced version through the shop's options menu)Same dimensions as the Zenoah G230, G240, G260, G270.New generation Zenoah engine with 28,5ccm cylinder capacity and approx. 3.9 hp. The cylinder is fixed with 4 screws. The technical details are identical to the Zenoah engines G240RC and G270RC.The engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter and / or complete clutch are optionally available at additional charge. Compatibility Zenoah / Losi 5ive-T:Please note that for installation in a Losi 5ive the fan cover must be swapped for a Losi or CY cover #5341 in order to fit the chassis" bolt pattern.If you want to install a Zenoah engine into the Losi 5ive, you usually have to use a fan cover from the CY engine.However, there is a workaround to maintain Zenoah fan cover.The adjustment is done via the pinion specific mounting plates for the engine. The change always affects only the rear, outer (carburetor side) plate under the fan cover. This is rotated by 180°; so that the embossed number on this plate faces the exhaust side of the engine!18T pinion: use 20T plate, rotated 180°19T pinion: use 19T plate, rotated 180°20T pinion: use 18T plate, rotated 180°On the plus side you gain the opportunity to easily mount a Zenoah engine keeping the original fan cover. On the other hand there will be the disadvantage of the necessity to combine two different sets of engine mounting plates when installing any pinion other than the stock 19T version. Therefore we do not recommend this workaround for everyday use. Nevertheless it works perfectly should ever the need arise.Zenoah G320RC with Walbro WT 1107 carburetor (also available in the ball-raced version through the shop's options menu)With 32 cm³ and 30% more power than the Zenoah G290.Significantly more torque and higher stamina due to larger sized bearings all around, with Racing Carburetor Walbro WT 1107.The motor is supplied with WT-1107 carburetor and spark plug.SpecificationType: Two stroke gasoline engineDisplacement: 31,8 cm³Bore: 38 mmStroke: 28 mmWeight: 2,3 KgOverall Dimension:Length: 167 mmWidth: 215 mmHeight: 196 mmMaximum Output: 4,6 PSMaximum Torque: 2,00 N-mRotation Direction: CounterclockwiseCarburetor: Walbro WT-1107Spark plug: CMR7HStarting: Recoil starterFor all HPI Baja 5 cars the G320RCer clutch housing has to be shortened at the mounting base, for Losi 5ive- T and Desert Buggy XL cars the clutch housings overall length must be shortened to CY size.When installing the air filter you must pay attention to the length of the screws.For use on Losi and HPI we recommend M5x45 screws (like H94763); you can also cut existing screws to length, of course.When ordering with a modified clutch housing we will include these screws!In our shop you can select from Zenoah G320RC engines already modified to fit your HPI or Losi car.The installation of the Zenoah G320RC in other cars (like FG or Smartech buggies / monsters a.s.o.) is not even remotely straightforward, since the layshaft pinion (the small pinion in front of the big differential spur gear) is in the way for the larger Zenoah G320RC crankcase.Compatibility Zenoah / Losi 5ive-T:Please note that for installation in a Losi 5ive the fan cover must be swapped for a Losi or CY cover #5341 in order to fit the chassis" bolt pattern.If you want to install a Zenoah engine into the Losi 5ive, you usually have to use a fan cover from the CY engine.However, there is a workaround to maintain Zenoah fan cover.The adjustment is done via the pinion specific mounting plates for the engine. The change always affects only the rear, outer (carburetor side) plate under the fan cover. This is rotated by 180°; so that the embossed number on this plate faces the exhaust side of the engine!18T pinion: use 20T plate, rotated 180°19T pinion: use 19T plate, rotated 180°20T pinion: use 18T plate, rotated 180°On the plus side you gain the opportunity to easily mount a Zenoah engine keeping the original fan cover. On the other hand there will be the disadvantage of the necessity to combine two different sets of engine mounting plates when installing any pinion other than the stock 19T version. Therefore we do not recommend this workaround for everyday use. Nevertheless it works perfectly should ever the need arise.

Genuine FG spare/option part. Contents:1 set

Complete universal set of screws, nuts and washers for all 1/5 and 1/6 scale FG vehicles (except Competition/Evo alloy models).The set includes a total of 309 screws, nuts and washers in different quantities.13 sizes of cap head screws8 sizes of CSH screws3 sizes of button head screws7 sizes of set screws6 sizes of washers3 sizes of self-locking nuts2 sizes of nuts9 sizes of self tapping screws3 sizes of CSH self tapping screws3 sizes of pan head screwsComes in a high quality 190x170x40 mm assortment box.Contents:Cap head screws in 12.9:3 piecesM3x82 piecesM3x161 piecesM3x183 piecesM3x209 piecesM4x202 piecesM4x252 piecesM4x301 piecesM4x451 piecesM5x162 piecesM5x251 piecesM6x103 piecesM6x401 piecesM6x75CSH screws in 10.9:2 piecesM4x162 piecesM4x258 piecesM4x401 piecesM5x142 piecesM5x256 piecesM5x302 piecesM5x351 piecesM6x16Button head screws in 10.9:10 piecesM4x82 piecesM4x142 piecesM5x40Grub screws:2 piecesM4x305 piecesM5x52 piecesM5x164 piecesM5x252 piecesM5x302 piecesM5x408 piecesM6x6Washers:2 piecesM3,2510 piecesM4,215 piecesM5,33 piecesM6,410 piecesM4,23 pieces10x16x1Self-locking nuts:3 piecesM316 piecesM410 piecesM5Normal nuts:8 piecesM54 piecesM5Sheet metal screws DIN 7981 Torx:7 piecesM2,9x9,52 piecesM2,9x131 piecesM2,9x192 piecesM2,9x226 piecesM4,2x9,59 piecesM4,2x1314 piecesM4,2x1614 piecesM4,2x225 piecesM4,2x32Countersunk head senk sheet metal screws DIN7982 Torx:14 piecesM4,2x1348 piecesM4,2x162 piecesM4,2x32Button head screws DIN 7985 Phillips (Kreuzschlitz) Verz. 4.8:4 piecesM3x41 piecesM3x252 piecesM4x14

TURBO-TWIST, 325 mm long screw driver in top quality. Allows you to set the carburetor on almost any 1:5 / 1:6 model also with a mounted body shell.On most models, you have to adjust the motor with this screwdriver does not even stoop.Caution:May differ from picture!