Skip to main content Skip to search Skip to main navigation
EXTRA 20% off Outlet*. Use Code: EXTRA20 at checkout!!
+49 2151 820200 Mon-Fri 9 am - 6 pm, Sa 9 am - 1 pm

67360 FG Conversion kit for gear brake Leopard

Product information "67360 FG Conversion kit for gear brake Leopard"

Genuine FG spare/option part.

The gear set is needed to convert the Leopard 2 and Leopard 4 Competition with 4 disk brakes to the lighter gear brake. According to the loss of brake and servo parts we achieved a weight reduction of approx. 350 grams.

Content:
  • 1 set

0 of 0 reviews

Average rating of 0 out of 5 stars

Leave a review!

Share your experiences with other customers.


Accessories / Spare parts

Average rating of 0 out of 5 stars

67338 FG Aluminum gear flange engine mount, gear brake
Replacement part for: 67360 Conversion kit for gear brake LeopardContents:1 piece

€161.95*

Customers also bought

Average rating of 0 out of 5 stars

5705 Mielke Big Tornado tuned pipe
Genuine Mielke spare/option part. Even better uniform power over the whole speed range. Especially in the major driving areas from 10.000 rev / min. to full speed. With 560 grams ideal weight for balanced driveability. Center of mass as low as possible new construction. Only 0,8 mm of specially thin steel metal.Compared to its predecessor the tube's diameter increased for about 10 mm. which allows for the better performance. The new set also comes with teflon seal # 5702.Including manifold and mounting material.Suitable for: 1:5 on road 2WD FG Sportsline, Evo- and Competition cars Mecatech FW01 S88R Harm SX4, SX5 Genius Contents:1 piece

€249.00*

Average rating of 0 out of 5 stars

Receiver switch, universal connectors, F1408 - 1pce.
Futaba / universal type connectors for both battery and receiver.

€9.90*

Average rating of 0 out of 5 stars

y0695 HT Tool bag
Tools and decorative items are for presentation purpose only and not included. Genuine HT spare/option part. Tool bag, extremely rugged tool bag made from reinforced fabric, sewn edge. With 41 flexible attachment loops for various tools with all-round zipper and reinforced handle.Dimensions:Width: 510 mm Height: 275 mmContents:1 piece

€24.90*

Average rating of 0 out of 5 stars

9473 FG Ball drive set for Leopard 2WD/4WD Sportsline, set
Item N° 9473Ball drive set for Leopard Sportsline, setFits for 2WD/4WD Sportsline.Not suitable for front application on 4WD cars!

€138.50*

Similar products

Average rating of 0 out of 5 stars

y1218 Springs for drive shafts
Genuine HT spare/option part. The best solution for drive shaft positioning, can be used with ball drives or regular "dog bones" as well.The springs will be simply inserted into the drive cups.DImensions:Diameter: 11 mmHeight: 8 mmContents:4 piece

€4.90*

Average rating of 0 out of 5 stars

y1004 Driveshaft boots for ball drive + dogbones
Genuine HT spare/option part. Protect ball drive as well as cardan drive against dirt. For FG and Carson ball drives, fits standard dogbones as well.Contents:2 pieces

€8.90*

Average rating of 0 out of 5 stars

y6107/02 Wheel squares 18 mm HART-COAT, 17 mm wide
Genuine HT spare/option part.Wheel squares made of high-strength aluminum, hardened, with two M6 mounting threads Suitable for most 1/6 and 1/5 rc-cars. Through the use of two 6 mm screws a significantly higher retention force is achieved. Yet it is still recommended to use medium strength thread lock (link y0114)! The hard anodizing (HART-COAT) guarantees much lower wear of the squares! Especially recommended when using wheel mounted brake discs! Four 3x16 dowel pins per square are included which prevent the squares from spinning in the rim. Press fitting them into the wheel squares is optional. The 12, 14 and 17 mm wide squares feature a groove for inserting a C-clip (link 6106/05), which acts as a guide for the brake disk. The narrow 9.5 mm wide squares dont need a clip; the close sitting rim will guide the disk. Measures18 mm square (wheel drive!)17 mm wide, 8.0 mm diameter axle boretwo M6 mounting threads The set includes 2 pieces of 17 mm wide wheel squares and 4 pieces each of M6 grub screws and 3x16 dowel pins.Contents:2 pieces

€18.95*

Average rating of 0 out of 5 stars

y6107/01 Wheel squares 18 mm HART-COAT, 14 mm wide
Genuine HT spare/option part.Wheel squares made of high-strength aluminum, hardened, with two M6 mounting threads Suitable for most 1/6 and 1/5 rc-cars. Through the use of two 6 mm screws a significantly higher retention force is achieved. Yet it is still recommended to use medium strength thread lock (link y0114)! The hard anodizing (HART-COAT) guarantees much lower wear of the squares! Especially recommended when using wheel mounted brake discs! Four 3x16 dowel pins per square are included which prevent the squares from spinning in the rim. Press fitting them into the wheel squares is optional. The 12, 14 and 17 mm wide squares feature a groove for inserting a C-clip (link 6106/05), which acts as a guide for the brake disk. The narrow 9.5 mm wide squares dont need a clip; the close sitting rim will guide the disk. Measures18 mm square (wheel drive!)14 mm wide, 8.0 mm diameter axle boretwo M6 mounting threads The set includes 2 pieces of 14 mm wide wheel squares and 4 pieces each of M6 grub screws and 3x16 dowel pins.Contents:2 pieces

€17.45*

Average rating of 0 out of 5 stars

y04475 HT Rear alloy shock mount 2WD
Genuine HT spare/option part.Rear alloy damper plate with several adjustment possibilities of the shock absorbers. Replacement for FG plastic rear shock tower FG 7072/01Please note: When installing in combination with plastic diff mounts you should insert a-arms with hinge pins before bolting together rear plate and diff mounts.Content:1 pieces

€89.90*

Average rating of 0 out of 5 stars

y0897 Wheelie bar with suspension for 2WD + 4WD models - 1pce.
Wheelie bar with double ball raced wheel, cnc-machined from high strength alloy. The arm has a rubber suspension unit, the height is infinitely adjustable. The suspension allows for a maximum deflection of 30 degrees and is dirt- and mud-proof. The wheel bearings are sealed.The unit fits FG Monster Truck, Monster Beetle and Marder BigFoot, except for Monster Buggy Off-Road WB535 4WD. Installation on other models will be possible, but requires modifications to the chassis, mainly to accept the bolt pattern. The Carson Attack already has the correct pattern.

€89.90*

Average rating of 0 out of 5 stars

y1072 HT Alloy differential spur gear protector
Genuine HT spare/option part.Gear protector for the bottom of the 2WD chassis plate. Replaces stock plastic part FG 6082 or Carson 32481.Contents:1 piece

€29.90*

Average rating of 0 out of 5 stars

y6479 HT rear alloy upright
Genuine HT spare/option part.Alloy upright for a ball fastening at the upper wishbone. Adjustable at the lower wishbone (hinge pin), too. Fits the rear axle of all FG and Carson / Smartech 1/6 scale cars.Comes with adjustment clips and grub screws for the hinge pins included.Dimensions:Bearing seats: 22 x 7 mmHinge pin bore: 6 mmDistance wheel shaft/hinge pin: 25 mm Contents:2 pieces

€89.90*

Average rating of 0 out of 5 stars

6479 FG Rear alloy uprights 08
Alloy upright for a ball fastening at the upper wishbone. Adjustable at the lower wishbone (wishbone pin), too. Fits the rear axle of all FG offroad cars (2WD and 4WD) and all Carson / Smartech cars.Content:Bearing seats: 22 x 7 mmHinge pin bore: 6 mmDistance wheel shaft/hinge pin: 25 mm

€133.95*

Average rating of 0 out of 5 stars

7497/01 FG Rear brake 2WD/4WD
Genuine FG spare/option part. The set will shipped without gear carrier plate. Contents:1 set

€55.90*

Average rating of 0 out of 5 stars

y0669 Rear alloy upright for 1:5 and 1:6 models
Genuine HT spare/option part. Rear alloy uprights for 1:5 and 1:6 models and 4WD Porsche, CNC-cut, optimal fitting, non-twisting even by heat.Dimensions:Bearing seats: 22 x 7 mmHinge pin bore: 6 mmDistance wheel shaft/hinge pin: 20 mmContents:1 set

€74.90*

Average rating of 0 out of 5 stars

y1621 Differential cover set for FG / Carson 2WD off-road cars
This two-piece differential cover is easy to attach with the existing screws and provides optimal protection against stones and dirt. Suitable for all 2WD FG Offroad models, not suitable for the 2WD models that are based on 4WD e.g. Fun Cross, Leopard, Truggy and all WB535 models.Also suitable for Carson 2WD models e.g. Uno, Attack, Gas Blaster and more.Contents:1 set

€19.90*

Customers also viewed

Average rating of 0 out of 5 stars

5705 Mielke Big Tornado tuned pipe
Genuine Mielke spare/option part. Even better uniform power over the whole speed range. Especially in the major driving areas from 10.000 rev / min. to full speed. With 560 grams ideal weight for balanced driveability. Center of mass as low as possible new construction. Only 0,8 mm of specially thin steel metal.Compared to its predecessor the tube's diameter increased for about 10 mm. which allows for the better performance. The new set also comes with teflon seal # 5702.Including manifold and mounting material.Suitable for: 1:5 on road 2WD FG Sportsline, Evo- and Competition cars Mecatech FW01 S88R Harm SX4, SX5 Genius Contents:1 piece

€249.00*

Average rating of 0 out of 5 stars

Receiver switch, universal connectors, F1408 - 1pce.
Futaba / universal type connectors for both battery and receiver.

€9.90*

Average rating of 0 out of 5 stars

y0695 HT Tool bag
Tools and decorative items are for presentation purpose only and not included. Genuine HT spare/option part. Tool bag, extremely rugged tool bag made from reinforced fabric, sewn edge. With 41 flexible attachment loops for various tools with all-round zipper and reinforced handle.Dimensions:Width: 510 mm Height: 275 mmContents:1 piece

€24.90*

Average rating of 0 out of 5 stars

6250/08, FG Conversion kit to Tuning disk brake f./r., set
Conversion kits to convert a front or rear disk brake to a Tuning disk brake for front or rear axle.Kit 06250/08 fits all rims from Ø100mm.Kit 08450/08 fits all rims up to Ø90mm.

€99.50*

Average rating of 0 out of 5 stars

68500, FG 4WD conversion kit for 2WD monster / stadium cars, set
Fits FG Monster and Stadium carsAre you owner of a Monster Truck or Monster Jeep, or perhaps of a Stadium Hummer? You are not really satisfied with the driving performance of your model, or you just want more driving fun? In this case we recommend to install the new 4WD conversion kit made by FG. The conversion kit includes all parts necessary to convert your 2WD Monster model to a 4WD model (complete front diff included). Assembly instructions are included.Fits the following FG cars:- Monster Truck- Monster Hummer- Monster Jeep- Monster Beetle Pro- Stadium Truck-Stadium Hummer- Stadium Jeep- Stadium Beetle ProPlease note: the radio plate is designed to accept a 805-sized servo (case length 65 mm). For installation of a Rhino (case length 58 mm) or a similar sized servo you need to order radioplate y0532 separately.The exploded view shows a partially assemled kit, therefore you can't see every single part included! The video shows the FG Off-Road Buggy 4WD during a test drive for a presentation in the Cars & Details magazine!The entire chassis is 100% identical to the FG cars Marder 4WD; Beetle 4WD and Monster / Stadium 4WDEnjoy the video!

€399.95*

Average rating of 0 out of 5 stars

10530 FG 4-block clutch 05 adjustable
Genuine spare/option part.Reliable and approved 4-block clutch with teflon linings, adjustable. The well approved clutch was reworked in some details. This clutch is excellent for the use in Off-Road models and is distinguised through reliability and low wear.Adjustable and in many details improved 4-block clutch. This clutch is suitable for all FG models and other brands with Zenoah or CY engines.Not suitable for HPI cars.Contents:1 piece

€119.50*

Average rating of 0 out of 5 stars

67206 FG Truggy wheel 1:6, black
Genuine FG spare/option part.Dimensions:Diameter: 140 mmWidth: 80 mm

€15.90*
Loading...
Upload in progress, please be patient ...
Shopware-Plugin Development Shopware-Theme Development