6074/02 FG Rear upper wishbone 2WD M8
€27.90
Available
Product information "6074/02 FG Rear upper wishbone 2WD M8"
Fits all other FG cars (except Evo and Formula 1) as well.
Dimensions:
- Length 42 mm
- Width 47 mm
Contents:
- 2 pieces
Login
Alternatives
Genuine HT spare/option part.Rear upper alloy wishbone with droop stop. Replacement for plastic wishbone FG 6074/02.Will also fit the following Carson/Smartech cars:Onroad chassis C5, Attack, Super Attack, Gas Blaster and TouaregCarson Comanche, Attack Evo, CRT + CPT when installedwith 75 mm turnbuckle y0988Comes with 2 M8 low height nuts included. Contents:2 pieces
Customers also bought
Genuine FG spare/option part. Fits all FG-Marder, Beetle, Pajero und Monster Beetle.Measures:Length: 79 mmDiameter: 6 mm Contents:2 pieces
Genuine HT spare/option part.Wheel squares made of high-strength aluminum, hardened, with two M6 mounting threads Suitable for most 1/6 and 1/5 rc-cars. Through the use of two 6 mm screws a significantly higher retention force is achieved. Yet it is still recommended to use medium strength thread lock (link y0114)! The hard anodizing (HART-COAT) guarantees much lower wear of the squares! Especially recommended when using wheel mounted brake discs! Four 3x16 dowel pins per square are included which prevent the squares from spinning in the rim. Press fitting them into the wheel squares is optional. The 12, 14 and 17 mm wide squares feature a groove for inserting a C-clip (link 6106/05), which acts as a guide for the brake disk. The narrow 9.5 mm wide squares dont need a clip; the close sitting rim will guide the disk. Measures18 mm square (wheel drive!)17 mm wide, 8.0 mm diameter axle boretwo M6 mounting threads The set includes 2 pieces of 17 mm wide wheel squares and 4 pieces each of M6 grub screws and 3x16 dowel pins.Contents:2 pieces
Genuine FG spare/option part. The Maxi-Grip tire develops more road grip and has a better balanced driving performance on a very uneven ground according to its bigger tire diameter and the improved rubber mixture. Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable.Diameter x width: 165 x 65 mmRim with 18 mm square driveContent:2 pieces
Genuine FG manual as included with the car.
Genuine FG spare/option part. Suitable for all 1:6 models except Race-Trucks as well as LeopardContents:1 piece
Genuine FG spare/option part. Suitable for all 1:6 models except Race-Trucks as well as LeopardContents:1 piece
Customers also viewed
Fits FG Monster and Stadium carsAre you owner of a Monster Truck or Monster Jeep, or perhaps of a Stadium Hummer? You are not really satisfied with the driving performance of your model, or you just want more driving fun? In this case we recommend to install the new 4WD conversion kit made by FG. The conversion kit includes all parts necessary to convert your 2WD Monster model to a 4WD model (complete front diff included). Assembly instructions are included.Fits the following FG cars:- Monster Truck- Monster Hummer- Monster Jeep- Monster Beetle Pro- Stadium Truck-Stadium Hummer- Stadium Jeep- Stadium Beetle ProPlease note: the radio plate is designed to accept a 805-sized servo (case length 65 mm). For installation of a Rhino (case length 58 mm) or a similar sized servo you need to order radioplate y0532 separately.The exploded view shows a partially assemled kit, therefore you can't see every single part included! The video shows the FG Off-Road Buggy 4WD during a test drive for a presentation in the Cars & Details magazine!The entire chassis is 100% identical to the FG cars Marder 4WD; Beetle 4WD and Monster / Stadium 4WDEnjoy the video!
Genuine FG spare/option part. Fits FG 2WD Marder.Offer your Marder a new life - it will be out of all recognition! Aggressive in the curves, dead on the line - just everything which guarantees pure driving fun. The well-tried 4WD by FG is now available as conversion kit for your 2WD Marder. You will not realize from the outside that the model is equipped with a fourwheel drive. But you and your rc-car friends will notice it considerably as soon as you start your model and speed up properly.The conversion kit includes all parts necessary to convert your 2WD Marder to a 4WD Buggy. A mounting instruction is enclosed.Please note: the radio plate is designed to accept a 805-sized servo (case length 65 mm). For installation of a Rhino (case length 58 mm) or a similar sized servo you need to order radioplate 68241 separately.Contents:1 set
The sets include complete front bulkheads A + B with brace, upper (adjustable) and lower a-arms and shock tower.Please note: the hinge pins are not included, you will use the pins from the stock suspension!The sets include:Item N°Name:y1027HT Aluminum a-arm 2WD, front uppery1026HT Aluminum a-arm 2WD, front lower, one-piecey1028HT Aluminum front bulkhead A for 2WDy1030HT Aluminum front bulkhead B for 2WDy1036HT rose joints with conical spacersy1029HT aluminum droop stopsy1035HT Aluminum shock tower Off-Road Buggy 2WDy1031HT Aluminum bulkhead brace for 2WDUnit prices: 387,10 EURFits FG Off-Road Buggy 2WD.This front suspension can be used on a FG Monster Beetl 2WD as well, however some new holes must be drilled into the shock tower for this application.
Genuine FG spare/option part.Contents:1 piece
Genuine FG spare/option part. Reinforced plastic ball-and-socket joints for M8 thread rods. Replacement for the plastic ball-and-socket joints 6029/01.Fits 10 mm balls, total length 39 mm.Contents:4 pieces
Genuine FG spare/option part. Contents:4 pieces