Product information "y0913 Original Zenoah G260 rebuild kit fits too CY, Losi and HPI engines, set"
Rebuild kit for the Zenoah G260/04 engine to replace piston/cylinder related parts, fits the previous G260 engines as well. The kit includes the following parts:
Cylinder G260
Piston G260
Piston ring G260
Piston bolt G260
Piston pin retainer clips
Cylinder gasket
This kit can also be installed on CY26, HPI and Losi engines, but you have to use Zenoah needle bearing 7312 and spacer washers 7312/0 for this application!
Please note: It is recommended to use a gasket sealer with every gasket on an engine. This gives better sealing anda longer lasting gasket. We also recommend:
Especially for installation of all engine gaskets. Temperature resistant from -55 °C to +200 °C. Resistant to water, mineral oils, synthetic lubricants, fuels, organic solvents and refrigerants. info: Hand tight: 10 - 20 minReady to use: 1 - 3 hoursGap fill: 0.5 mmContent: 50 ml Notes for usage: This surface seal is not for use as the sole sealant, it should always be applied in combination with a paper gasket.The HT-surface sealing agent should be sparsely applied over the entire surface, with care being taken that the sealant does not enter the devices internals (e.g. crankcase, differential a.s.o.) during the assembly.
Bindulin liquid rubber - very high elasticitySuitable for additional sealing of tuned pipes and exhaust / manifold connections .Temperature resistant from -60 ° to + 180 ° CResistant against diluted acids.Also for sealing threaded joints, electric lines and cable lead-throughs in receiver boxes.The surfaces must be clean, grease free and dry (brake cleaner).Contents:1 piece / 45 grams
Marston Universal blue is the leading non-setting gasket and sealing compound in use world-wide. The product is used by many of the world?s major automotive manufacturers and by several Formula 1 teams.Features- Non hardening and non setting- Unlimited assembly time- Vibration resistant- Allows metal to metal contact- Resistant to combustion products, water, engine coolant, petroleum, lubricating oils, kerosene and fluorocarbon refrigerants- Seals surface imperfections- Withstands rapid variations in temperature80 ml tube
Genuine MD spare/option part. The red version with a temperature resistant up to 300°C. Directions for use:Clean the surfaces with a cleaner. Apply MD-Sil on one side and press the parts together. Touch-dry in 10 - 20 minutes. Curing speed 3 mm/24 hours. Contents:1 piece / 80 ml
Genuine HT spare/option part. Special fabric bag to protect engines, rc-plates or other expensive items. Large opening and pull-string closure.Size:Diameter 200 mmHeight 200 mmContents:1 pieceAccessories not included.
Genuine FG spare/option part. Gasket kit for the Zenoah engines G230 and G260RC. Actual product may be of different color. We have no bearing on this since we are not the manufacturer.Set includes the following parts:7332 Silencer gasket for CY / Zenoah7335 Insulator gasket for CY / Zenoah7337 Carburetor gasket for Zenoah, CY7305/08 Crankcase gasket for CY / Zenoah 7306/09 Special Cylinder foot gasket CY / Zenoah Please note:It is recommended to use a gasket sealer with every gasket on an engine. This gives better sealing anda longer lasting gasket. We also recommend:y0804 HT-flange sealer 518 y0994 Marston sealery0807 MD-Sil RTV silicone sealer
Rebuild kit for the Zenoah G290 engine to replace piston/cylinder related parts. The kit includes the following parts:Cylinder G290Piston G290Piston ring G290Piston pin G290Piston pin retainer clipsCylinder gasketPlease note:It is recommended to use a gasket sealer with every gasket on an engine. This gives better sealing anda longer lasting gasket. We also recommend:y0804 HT-flange sealer 518 y0994 Marston sealery0807 MD-Sil RTV silicone sealer
Rebuild kit for the Zenoah G270 engine to replace piston/cylinder related parts. The kit includes the following parts:Cylinder G270Piston G270Piston ring G270Piston pin G270Piston pin retainer clipsCylinder gasketPlease note:It is recommended to use a gasket sealer with every gasket on an engine. This gives better sealing anda longer lasting gasket. We also recommend:y0804 HT-flange sealer 518 y0994 Marston sealery0807 MD-Sil RTV silicone sealer
Cylinder-piston repair kit for Zenoah engine G230. Set includes the following parts:Cylinder, piston, piston ring, cylinder foot gasket, centering disks, piston pin clip.Please note:It is recommended to use a gasket sealer with every gasket on an engine. This gives better sealing anda longer lasting gasket. We also recommend:y0804 HT-flange sealer 518 y0994 Marston sealery0807 MD-Sil RTV silicone sealer
Rebuild kit for the Zenoah G240 engine to replace parts. The kit includes the following parts:Cylinder G240Piston G240Piston ring G240Piston pin G240Piston pin retainer clipsCylinder gasketPlease note:It is recommended to use a gasket sealer with every gasket on an engine. This gives better sealing anda longer lasting gasket. We also recommend:y0804 HT-flange sealer 518 y0994 Marston sealery0807 MD-Sil RTV silicone sealer
7387 Rebuilt kit Zenoah G230Cylinder-piston repair kit for Zenoah engine G230. Set includes the following parts:Cylinder G230Piston G230Piston ring G230Cylinder foot gasketCentering disksPiston pin clipy0914 Original Zenoah G240 rebuild kitRebuild kit for the Zenoah G240 engine to replace piston/cylinder related parts. The kit includes the following parts:Cylinder G240Piston G240Piston ring G240Piston pin G240Piston pin retainer clipsCylinder gaskety0913 Original Zenoah G260 rebuild kit fits too CY, Losi and HPI enginesRebuild kit for the Zenoah G260 engine to replace piston/cylinder related parts, fits the G260 engines as well. The kit includes the following parts:Cylinder G260Piston G260Piston ring G260Piston pin retainer clipsCylinder gasketThis kit can also be installed on CY26, HPI and Losi engines, but you have to use Zenoah needle bearing 7312 and spacer washers 7312/01 for this application! y0915 Original Zenoah G270 rebuild kitRebuild kit for the Zenoah G270 engine to replace piston/cylinder related parts. The kit includes the following parts:Cylinder G270Piston G270Piston ring G270Piston pin G270Piston pin retainer clipsCylinder gaskety0916 Original Zenoah G290 rebuild kitRebuild kit for the Zenoah G290 engine to replace piston/cylinder related parts. The kit includes the following parts:Cylinder G290Piston G290Piston ring G290Piston pin G290Piston pin retainer clipsCylinder gaskety1016/095 Original Zenoah 32 cm³ 4 Bolt Rebuilt kitOriginal Zenoah 32 cm³ Rebuilt kit Top quality with Zenoah warranty!Set includes the following parts: CylinderPistonPiston ringCylinder foot gasketPiston pinPiston pin clipThrust washer for needle bearingCover for transfer portAttention: For the assembling of the covers enclosed please use the HT-flange sealer y804 and pay attention to the assembling instructions enclosed.Please note:It is recommended to use a gasket sealer with every gasket on an engine. This gives better sealing anda longer lasting gasket. We also recommend:y0804 HT-flange sealer 518 19015 Bindulin Siliconey0994 Marston sealery0807 MD-Sil RTV silicone sealer
The first 29 cc conversion kit made by Zenoah. Top quality with Zenoah warranty!Set includes the following parts: CylinderPistonPiston ringCylinder foot gasketPiston pinPiston pin clipSpark plugMore power through more displacement! Please note that fhe following limimitations for displacement apply at official races: 1/5 ON-ROAD 2WD max.23 cm³1/5 ON-ROAD 4WD max.26 cm³1/5 Formula 1 max.26 cm³1/6 OFF-ROAD 2WD + 4WD26 cm³Please note:It is recommended to use a gasket sealer with every gasket on an engine. This gives better sealing anda longer lasting gasket. We also recommend:More power through more displacement! Please note that fhe following limimitations for displacement apply at official races: 1/5 ON-ROAD 2WD max.23 cm³1/5 ON-ROAD 4WD max.26 cm³1/5 Formula 1 max.26 cm³1/6 OFF-ROAD 2WD + 4WD26 cm³Please note:It is recommended to use a gasket sealer with every gasket on an engine. This gives better sealing anda longer lasting gasket. We also recommend:y0804 HT-flange sealer 518 y0994 Marston sealery0807 MD-Sil RTV silicone sealer
Original Zenoah 32 cm³ Rebuilt kit Top quality with Zenoah warranty!Set includes the following parts: CylinderPistonPiston ringCylinder foot gasketPiston pinPiston pin clipThrust washer for needle bearingCover for transfer portAttention: For the assembling of the covers enclosed please use the HT-flange sealer y804 and pay attention to the assembling instructions enclosed.Please note:It is recommended to use a gasket sealer with every gasket on an engine. This gives better sealing anda longer lasting gasket. We also recommend:y0804 HT-flange sealer 518 y0994 Marston sealery0807 MD-Sil RTV silicone sealer
Genuine FG spare/option part. Conversion set from G230 with 23 cm³ to G260 with 26 cm³. Set includes the following parts: CylinderPistonPiston ringCylinder foot gasketPiston pinPiston pin clipSpark plugMore power through more displacement! Please note that fhe following limimitations for displacement apply at official races: 1/5 ON-ROAD 2WD max.23 cm³1/5 ON-ROAD 4WD max.26 cm³1/5 Formula 1 max.26 cm³1/6 OFF-ROAD 2WD + 4WD26 cm³Please note:It is recommended to use a gasket sealer with every gasket on an engine. This gives better sealing anda longer lasting gasket. We also recommend:More power through more displacement! Please note that fhe following limimitations for displacement apply at official races: 1/5 ON-ROAD 2WD max.23 cm³1/5 ON-ROAD 4WD max.26 cm³1/5 Formula 1 max.26 cm³1/6 OFF-ROAD 2WD + 4WD26 cm³Please note:It is recommended to use a gasket sealer with every gasket on an engine. This gives better sealing anda longer lasting gasket. We also recommend:y0804 HT-flange sealer 518 y0994 Marston sealery0807 MD-Sil RTV silicone sealer
Cylinder-piston repair kit for Zenoah engine G240 (to increase displacement to 26 cm³). Set includes the following parts: CylinderPistonPiston ringCylinder foot gasketPiston pinPiston pin clipSpark plugMore power through more displacement! Please note that fhe following limimitations for displacement apply at official races: 1/5 ON-ROAD 2WD max.23 cm³1/5 ON-ROAD 4WD max.26 cm³1/5 Formula 1 max.26 cm³1/6 OFF-ROAD 2WD + 4WD26 cm³Please note:It is recommended to use a gasket sealer with every gasket on an engine. This gives better sealing anda longer lasting gasket. We also recommend:More power through more displacement! Please note that fhe following limimitations for displacement apply at official races: 1/5 ON-ROAD 2WD max.23 cm³1/5 ON-ROAD 4WD max.26 cm³1/5 Formula 1 max.26 cm³1/6 OFF-ROAD 2WD + 4WD26 cm³Please note:It is recommended to use a gasket sealer with every gasket on an engine. This gives better sealing anda longer lasting gasket. We also recommend:y0804 HT-flange sealer 518 y0994 Marston sealery0807 MD-Sil RTV silicone sealer
To celebrate the 30th anniversary of the legendary Marder 1/6 scale 2WD buggy, FG Modellsport/T2M releases a special edition, limited to 300 numbered pieces, with the original signature of Franz Gröschl on the sticker sheet as well as a top equipment (G260RC Zenoah engine, hi-capacity low friction aluminum shock absorbers and special aluminum engine mounts). with original 260 Zenoah with Low-Friction Alu shocks with alloy enginemount The Models is built on a 4 mm u-bended chassis. All borings of the lower side are countersunk, therefore the screw heads can't bear out.Double wishbones at font and rear axle as well as 4 bulk oil-pressure shock absorbers guarantee perfect ground adherence. All rotating parts are supported by ball-bearings. Rear gear wheels, differential gears and all driving elements are case-hardened. The side guards protect the model from dirt. With original signature of Franz Gröschl. The model is equipped with a powerfull 26 ccm engine which runs with normal 2-stroke petrol-oil mixture (available at every petrol station). The tank filling of 0,7 liters enables you to drive about 45 minutes. The engine can be started without difficulties through the integrated pull-start. To complete the models all merchantable servos and radio control systems are suitable.You can select the car with complete RTR-equipment from the options menu. RTR-equipment RTR = Ready to Run. The RTR version comes ready to use with the 2,4 GHz rc-system already installed. Transmitter: Reflex Wheel Pro III 2,4 GHzReceiver: Mini BECHigh power servo for throttle and brakeLargescale servo for steeringTx-battery, rx-battery
Servo direct power supply cable, 1 pce.With this cable the servos get their current directly from the battery without straining the receiver circuit board.Silicone insulated wires with 0.5 mm² cross section
y0557 Zenoah G230RC, with Walbro WT 603B carburetor (also available in the ball-raced version through the shop's options menu)23 cm³ Zenoah engine for large scale cars!The engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter and / or complete clutch are optionally available at additional charge.y1009 Zenoah G240RC with Walbro WT 990 carburetor (also available in the ball-raced version through the shop's options menu)23 cm³ Zenoah engine for large scale cars!Please note: contrary to their new designation the displacement has not been increased! The outer dimension didn't change, so you don't need any additional parts for the engine swap!The engines feature the following improvements over their G230RC:- Quantity of cylinder mounting bolts increased from 2 to 4- Improved strength of crankcase- Added additional bearing on the PTO (clutch) side of crankshaft- Redesigned shape of cylinder fins- Dimension of air intake port is 5% widerContains internal fuel pump which increases acceleration from idle to wide open throttle.Removal of choke valve increases performance by increasing air flow to the carburetor - Changed material of the insulator gasket to metal, which improves sealing performanceThe engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter and / or complete clutch are optionally available at additional charge. y0553 Zenoah G260RC with Walbro WT 603B carburetor (also available in the ball-raced version through the shop's options menu)This is the G260 in the 26 cm³ version.The engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter and / or complete clutch are optionally available at additional charge. y1011 Zenoah G270RC with Walbro WT 990 carburetor (also available in the ball-raced version through the shop's options menu)26 cm³ Zenoah engine for large scale cars!Please note: contrary to their new designation the displacement has not been increased! The outer dimension didn't change, so you don't need any additional parts for the engine swap!The engines feature the following improvements over their G260RC:- Quantity of cylinder mounting bolts increased from 2 to 4- Improved strength of crankcase- Added additional bearing on the PTO (clutch) side of crankshaft- Redesigned shape of cylinder fins- Dimension of air intake port is 5% wider- New carburetor (WT-990) Contains internal fuel pump which increases acceleration from idle to wide open throttle.Removal of choke valve increases performance by increasing air flow to the carburetor - Changed material of the insulator gasket to metal, which improves sealing performanceThe engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter are optionally available at additional charge. 7800 Zenoah G290RC with Walbro WT 990 carburetor (also available in the ball-raced version through the shop's options menu)Same dimensions as the Zenoah G230, G240, G260, G270.New generation Zenoah engine with 28,5ccm cylinder capacity and approx. 3.9 hp. The cylinder is fixed with 4 screws. The technical details are identical to the Zenoah engines G240RC and G270RC.The engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter and / or complete clutch are optionally available at additional charge. Compatibility Zenoah / Losi 5ive-T:Please note that for installation in a Losi 5ive the fan cover must be swapped for a Losi or CY cover #5341 in order to fit the chassis" bolt pattern.If you want to install a Zenoah engine into the Losi 5ive, you usually have to use a fan cover from the CY engine.However, there is a workaround to maintain Zenoah fan cover.The adjustment is done via the pinion specific mounting plates for the engine. The change always affects only the rear, outer (carburetor side) plate under the fan cover. This is rotated by 180°; so that the embossed number on this plate faces the exhaust side of the engine!18T pinion: use 20T plate, rotated 180°19T pinion: use 19T plate, rotated 180°20T pinion: use 18T plate, rotated 180°On the plus side you gain the opportunity to easily mount a Zenoah engine keeping the original fan cover. On the other hand there will be the disadvantage of the necessity to combine two different sets of engine mounting plates when installing any pinion other than the stock 19T version. Therefore we do not recommend this workaround for everyday use. Nevertheless it works perfectly should ever the need arise.Zenoah G320RC with Walbro WT 1107 carburetor (also available in the ball-raced version through the shop's options menu)With 32 cm³ and 30% more power than the Zenoah G290.Significantly more torque and higher stamina due to larger sized bearings all around, with Racing Carburetor Walbro WT 1107.The motor is supplied with WT-1107 carburetor and spark plug.SpecificationType: Two stroke gasoline engineDisplacement: 31,8 cm³Bore: 38 mmStroke: 28 mmWeight: 2,3 KgOverall Dimension:Length: 167 mmWidth: 215 mmHeight: 196 mmMaximum Output: 4,6 PSMaximum Torque: 2,00 N-mRotation Direction: CounterclockwiseCarburetor: Walbro WT-1107Spark plug: CMR7HStarting: Recoil starterFor all HPI Baja 5 cars the G320RCer clutch housing has to be shortened at the mounting base, for Losi 5ive- T and Desert Buggy XL cars the clutch housings overall length must be shortened to CY size.When installing the air filter you must pay attention to the length of the screws.For use on Losi and HPI we recommend M5x45 screws (like H94763); you can also cut existing screws to length, of course.When ordering with a modified clutch housing we will include these screws!In our shop you can select from Zenoah G320RC engines already modified to fit your HPI or Losi car.The installation of the Zenoah G320RC in other cars (like FG or Smartech buggies / monsters a.s.o.) is not even remotely straightforward, since the layshaft pinion (the small pinion in front of the big differential spur gear) is in the way for the larger Zenoah G320RC crankcase.Compatibility Zenoah / Losi 5ive-T:Please note that for installation in a Losi 5ive the fan cover must be swapped for a Losi or CY cover #5341 in order to fit the chassis" bolt pattern.If you want to install a Zenoah engine into the Losi 5ive, you usually have to use a fan cover from the CY engine.However, there is a workaround to maintain Zenoah fan cover.The adjustment is done via the pinion specific mounting plates for the engine. The change always affects only the rear, outer (carburetor side) plate under the fan cover. This is rotated by 180°; so that the embossed number on this plate faces the exhaust side of the engine!18T pinion: use 20T plate, rotated 180°19T pinion: use 19T plate, rotated 180°20T pinion: use 18T plate, rotated 180°On the plus side you gain the opportunity to easily mount a Zenoah engine keeping the original fan cover. On the other hand there will be the disadvantage of the necessity to combine two different sets of engine mounting plates when installing any pinion other than the stock 19T version. Therefore we do not recommend this workaround for everyday use. Nevertheless it works perfectly should ever the need arise.
The first 29 cc conversion kit made by Zenoah. Top quality with Zenoah warranty!Set includes the following parts: CylinderPistonPiston ringCylinder foot gasketPiston pinPiston pin clipSpark plugMore power through more displacement! Please note that fhe following limimitations for displacement apply at official races: 1/5 ON-ROAD 2WD max.23 cm³1/5 ON-ROAD 4WD max.26 cm³1/5 Formula 1 max.26 cm³1/6 OFF-ROAD 2WD + 4WD26 cm³Please note:It is recommended to use a gasket sealer with every gasket on an engine. This gives better sealing anda longer lasting gasket. We also recommend:More power through more displacement! Please note that fhe following limimitations for displacement apply at official races: 1/5 ON-ROAD 2WD max.23 cm³1/5 ON-ROAD 4WD max.26 cm³1/5 Formula 1 max.26 cm³1/6 OFF-ROAD 2WD + 4WD26 cm³Please note:It is recommended to use a gasket sealer with every gasket on an engine. This gives better sealing anda longer lasting gasket. We also recommend:y0804 HT-flange sealer 518 y0994 Marston sealery0807 MD-Sil RTV silicone sealer
This website uses cookies to ensure the best experience possible. More information.... By clicking on "[Agree / Accept all / etc.]" you also give your consent to the disclosure of your behavior in our store to our partner, shopware AG (Ebbinghoff 10, 48624 Schöppingen, Germany), which cannot assign this data to you personally, but may process it for its own purposes (e.g. product improvements, market behavior analyses).