y0314 Electronic high current receiver switch
Product number:
schalter_elektronisch.0
EAN:
4058575017769
Product information "y0314 Electronic high current receiver switch"
Genuine HT spare/option part.
Electronic receiver switch, rated 5 A continuous / 15 A peak. This switch does not use mechanical contacts for the load, therefore it is less prone to failure caused by vibrations or dirt.
The swith uses two separate connectors to distribute the load at the receiver terminals.
With drilling template and mounting material.
Contents:
Electronic receiver switch, rated 5 A continuous / 15 A peak. This switch does not use mechanical contacts for the load, therefore it is less prone to failure caused by vibrations or dirt.
The swith uses two separate connectors to distribute the load at the receiver terminals.
With drilling template and mounting material.
Contents:
- 1 piece
Login
Similar products
tt_tt1000 Connector:
TT1000/01 Universal in - Universal out
Genuine Top Tuning spare/option part. Top Tuning The 20-amp Bigscale switch allows for a maximum input voltage of 30 volt. It is specifically designed as a receiver switch for use in combination with the Hitec HS-1005SGT servo and 4s receiver battery. The switch can also be used for other applications at your discretion with batteries up to 6S.Note: Top Tuning the electronic 20 amp Bigscale high voltage switch delivers the batterys full voltage. It does not replace a voltage regulator! The components which follow down the line (voltage regulator / servos / receiver) must be matched to this voltage! Using the latest MOSFET technology allows the 20 amp Bigscale high voltage switch to handle extreme loads, despite its small size. A blue LED status light clearly displays the activated mode. The 20 amp Bigscale high voltage switch is dust-and splash protected. He has an extremely low internal resistance and very low power consumption in off mode. Nevertheless it is recommended to unplug the battery when the model will not be used for an extended period. Properties:Voltage range: 3 to 30 VLoad: 20 ampsStandby consumption: 17 µAOperating temperature: - 15 ° C to +50 ° CCable length:Battery side 250 mmReceiver side 130 mmWeight: 13 gramsDimensions:Length: 29 mm Width: 13 mmHeight: 12 mmContents:1 piece
Futaba / universal type connectors for both battery and receiver.
BEC type connectors for both battery and receiver.
schalter_elektronisch Battery connector:
y0314/02 FG connector+ 5EUR
Genuine HT spare/option part.Electronic receiver switch, rated 5 A continuous / 15 A peak. This switch does not use mechanical contacts for the load, therefore it is less prone to failure caused by vibrations or dirt.The swith uses two separate connectors to distribute the load at the receiver terminals.With drilling template and mounting material.Contents:1 piece
Variants from €39.90*
akku_0021 Battery connector:
y0210/04 MPX old
Genuine HT spare/option part. Water protected receiver switches, silver plated contacts. Many different connectors to choose from.UniversalFGBECHigh currentContents:1 piece
servo_strom_mit Application:
y0368 - 3 servos, battery connector universal+ 2EUR
Servo direct power supply cable with electronic switch, 1 pce.With this cable the servos get their current directly from the battery without straining the receiver circuit board.The integrated electronic receiver switch is rated 5 A continuous / 15 A peak. This switch does not use mechanical contacts for the load; therefore it is less prone to failure caused by vibrations or dirt. With separate charging connector.With drilling template and mounting material included.
Variants from €54.90*
Old version Multiplex type connectors for both battery and receiver.
Genuine FG spare/option part. Waterproof switch equipped with JR connector for receiver and FG gold contact connector for the receiver battery. Used to cut the power supply of receiver and battery. With fastening screw thread.Suitable for all radio control systems.Contents:1 piece
Genuine FG spare/option part. A switch which one well through a hole in the radio box and put on top and bottom can be secured with nuts.Contents:1 piece
Customers also viewed
schalter_elektronisch Battery connector:
y0314/02 FG connector+ 5EUR
Genuine HT spare/option part.Electronic receiver switch, rated 5 A continuous / 15 A peak. This switch does not use mechanical contacts for the load, therefore it is less prone to failure caused by vibrations or dirt.The swith uses two separate connectors to distribute the load at the receiver terminals.With drilling template and mounting material.Contents:1 piece
Variants from €39.90*
Genuine HT spare/option part.Wheel squares made of high-strength aluminum, hardened, with two M6 mounting threads Suitable for most 1/6 and 1/5 rc-cars. Through the use of two 6 mm screws a significantly higher retention force is achieved. Yet it is still recommended to use medium strength thread lock (link y0114)! The hard anodizing (HART-COAT) guarantees much lower wear of the squares! Especially recommended when using wheel mounted brake discs! Four 3x16 dowel pins per square are included which prevent the squares from spinning in the rim. Press fitting them into the wheel squares is optional. The 12, 14 and 17 mm wide squares feature a groove for inserting a C-clip (link 6106/05), which acts as a guide for the brake disk. The narrow 9.5 mm wide squares dont need a clip; the close sitting rim will guide the disk. Measures18 mm square (wheel drive!)17 mm wide, 8.0 mm diameter axle boretwo M6 mounting threads The set includes 2 pieces of 17 mm wide wheel squares and 4 pieces each of M6 grub screws and 3x16 dowel pins.Contents:2 pieces
tt_tt1000 Connector:
TT1000/02 FG in - Universal out
Genuine Top Tuning spare/option part. Top Tuning The 20-amp Bigscale switch allows for a maximum input voltage of 30 volt. It is specifically designed as a receiver switch for use in combination with the Hitec HS-1005SGT servo and 4s receiver battery. The switch can also be used for other applications at your discretion with batteries up to 6S.Note: Top Tuning the electronic 20 amp Bigscale high voltage switch delivers the batterys full voltage. It does not replace a voltage regulator! The components which follow down the line (voltage regulator / servos / receiver) must be matched to this voltage! Using the latest MOSFET technology allows the 20 amp Bigscale high voltage switch to handle extreme loads, despite its small size. A blue LED status light clearly displays the activated mode. The 20 amp Bigscale high voltage switch is dust-and splash protected. He has an extremely low internal resistance and very low power consumption in off mode. Nevertheless it is recommended to unplug the battery when the model will not be used for an extended period. Properties:Voltage range: 3 to 30 VLoad: 20 ampsStandby consumption: 17 µAOperating temperature: - 15 ° C to +50 ° CCable length:Battery side 250 mmReceiver side 130 mmWeight: 13 gramsDimensions:Length: 29 mm Width: 13 mmHeight: 12 mmContents:1 piece
The RHINO pro SHV digi 4 servo is a 29 mm digital servo designed for use in large-scale models. The new pro SHV servo is faster, more powerful, and more durable than the proven RHINO digi 4, of which thousands are now in use. More performance, with higher torque and faster transit speed, and more durable with a new triple-ballraced heavy-duty steel gear set. The operating voltage range has been expanded to 7.4 V, allowing the servo to be operated directly with up to two-cell LiPo batteries.Large 1 : 5 scale model cars make very exacting demands on the servos, and for many years the RHINO servo has set the standard with its extremely robust, outsize metal gearbox and 8 mm output shaft for the output device. An integral aluminium heat-sink cools the motor and electronics very effectively. Servo case gaskets make the unit dust-proof and splash-proof. The enormous power and robust nature of this servo also make it an excellent choice for large models generally, such as F3A - XXL large-scale model aircraft, as well as for non-standard applications.Adapter FG # 6118/02 is required for installation into a FG/Smartech car.High-voltage (HV) servosHV servos have a broad operating voltage range of 5 - 7.4 V, i.e. they can be operated directly with two-cell Lithium-based rechargeable batteries (e.g. LiPo, LiFe, LiIo). The outstanding features of LiXX batteries compared with NiXX types are their higher energy density and lower self-discharge rate, and for these reasons they are increasingly used as power supplies in model RC systems. The higher voltage of LiXX batteries means that the current drawn by an HV servo is lower for a given output power than that of conventional servos, which are generally designed for a nominal voltage of 4.8 - 6 V. When used with 2S LiXX batteries, these older servos must therefore be operated with a separate voltage reducer. This reduces the overall efficiency of the system, leads to unnecessary dissipated power, requires additional electronic complexity and more connectors ( higher costs, greater failure risk, higher weight). Modern receivers (e.g. M-LINK) are designed for voltages up to 9 V, i.e. with HV there is no longer any reason not to use the modern, superior LiXX battery technology.The following servo parameters can be adjusted using the MULTImate test and programming unit # 8 2094:Direction of servo rotationServo transit speedServo travel, left / right (max. 2 x 90°)Servo centreServo deadbandFail-safe (On with servo Fail-Safe position / Off)Reset to factory default settingsSpecificationDimensions (L x W x H):Weight::Gearbox:Ballraces:Multi-finger wiper pot:Torque @ 6 V / 7f.4 V*:Holding power @ 6 V / 7.4 V*:Transit speed for 40°@ 6 V / 7.4 V*: 59 x 29 x 55 mm172 gSteel3yes (with indirect drive)230 / 270 Ncm280 / 320 Ncm** 0,10 / 0,08 sec.* 5-cell NiXX / 2S LiPo operation. Values measured at stabilised 6.0 V / 7.4 V.** Holding power at angular error
y0657 Connector:
y0657/01 Futaba, JR, MPX universal
Genuine HT spare/option part. 5 cells, 6 volt, cell size Sub-C. More applications on request.Dimensions: approx 112 x 46 x 23 mmContents:1 piece
y0675 Connector:
y0675/01 FG connector
Item N° y0675 Receiver battery pack 5000 mAh Ni-Mh - 1pce.Double-block special battery pack, 6 volt / 5000 mAh, with FG or universal connector.Dimensions: approx. 72 x 53 x 29 mmConnector:UniversalFGEspecially designed for the high current demand in FG 4WD cars NiMh battery pack, fits the stock battery tray.Can be used for FG Evo cars and Competition cars as well.The Sanyo eneloop cell eliminates the annoying problem that a charged battery has often lost a high percentage of its storage capacity after just one week. Also, the differences between individual cells in a pack are sometimes significant, reducing the life and performance of the complete pack. Compared to "normal" NiMh cells the Sanyo eneloop cell has a slightly lower capacity and a slightly higher price (in relationship to its capacity), but you get significant advantages in return. With the recently available improved version of the 2005 introduced and widely acclaimed eneloop cell self-discharge for rc-car related time frames is now more or less nonexistent. One could easily charge the cells at New Year?s Eve and use them at Christmas without noticing a significant loss of capacity. Sanyo eneloop cells show a considerably reduced tendency to failure of individual cells in a battery pack. Even after years eneloop cells usually differ by only a few percent. The voltage of the cells is also slightly higher than with normal NiMh cells, so that more volts are available under load. Especially when used in largescale cars with their usually extremely strong servos, this is a particularly important feature! Chargers which are suitable for NiMh cells will also work for eneloop cells. The basic features of the eneloop XX version are similar to the standard version, but here the priorities were set slightly different. At the expense of reduced (but easy to cope with for rc-car usage) values for load cycles and self-discharge, capacity could be increased by 25%.- Nominal capacity: 2500 mAh- Maximum number of charge cycles: 500- self-discharge: 25% at 1 yearYou can differentiate the two generations of eneloop cells by checking the model name which is written on each eneloop. The "old" cells have written HR-3UTG (AA) on them, the improved eneloop instead HR-3UTGA (AA)!