F003/2 Carson Universal On/Off Switch
€9.90
Currently unavailable
Product information "F003/2 Carson Universal On/Off Switch"
Contents:
- 1 piece
Werkstrasse 1
90765 Fürth
Germany
Login
Customers also bought
In case the servo cable is not long enough.Two selectable lengths:y0428/01 - 180 mmy0428/02 - 300 mm
Genuine FG spare/option part. Suitable for all FG 1:5 and 1:6 2WD and 4WD models. Best fitting of ball bearing seat and distance of gear shaft, non-twisting. To mount this gear plate into the models Marder, Beetle, Beetle On-Road, Pajero and Monster the rear brake 7040/01 is needed.Bearing seatsClutch bell: 22 x 6 mmLayshaft: 19 x 7 mmContent:1 piece
Genuine FG spare/option part. This spacer bushing goes into the gear plate between the two clutch bell bearings, preventing them from binding when installing the pinion on the clutch bell.Contents:1 piece
Genuine FG spare/option part.Improved rear brake for Marder, Beetle Off-Road, Beetle On-Road and Pajero as well as EcoLine, not for Formula 1. Big epoxy brake disk (diameter 52 mm) for more brake power. Gear carrier is not included in the set. Only in connection with 7039/01or 7474.Contents:1 set
Suitable for all FG/Carson/Smartech cars except FG Evo and Carson 4WD.Please note that tank mount 7143 is required for installation. Installation in a Carson/Smartech 1/6 off-road car requires drilling of two new 4.5 mm diameter holes into the chassis plate. Drilling template is included.Comes as shown with fuel lines, grommet and gas cap included.
Customers also viewed
Genuine Top Tuning spare/option part. Top Tuning The 20-amp Bigscale switch allows for a maximum input voltage of 30 volt. It is specifically designed as a receiver switch for use in combination with the Hitec HS-1005SGT servo and 4s receiver battery. The switch can also be used for other applications at your discretion with batteries up to 6S.Note: Top Tuning the electronic 20 amp Bigscale high voltage switch delivers the batterys full voltage. It does not replace a voltage regulator! The components which follow down the line (voltage regulator / servos / receiver) must be matched to this voltage! Using the latest MOSFET technology allows the 20 amp Bigscale high voltage switch to handle extreme loads, despite its small size. A blue LED status light clearly displays the activated mode. The 20 amp Bigscale high voltage switch is dust-and splash protected. He has an extremely low internal resistance and very low power consumption in off mode. Nevertheless it is recommended to unplug the battery when the model will not be used for an extended period. Properties:Voltage range: 3 to 30 VLoad: 20 ampsStandby consumption: 17 µAOperating temperature: - 15 ° C to +50 ° CCable length:Battery side 250 mmReceiver side 130 mmWeight: 13 gramsDimensions:Length: 29 mm Width: 13 mmHeight: 12 mmContents:1 piece
Genuine FG spare/option part.Steel taper disks, 3.5 mm thick, with a higher stiffness compared to alloy taper disks. Installation of these disks allows for larger operation angles of the metal ball joints and rose joints. You need two disks per joint.Contents:4 pieces
Genuine Dynamite spare/option part.Key Features:Kills your 2-cycle gas engine on command, loss of radio signal, low battery, or total battery power lossComes ready to install no soldering requiredOptically Coupled to isolate your ignition system from your radio systemBuilt-in LED for easy-to-spot operational status3-Channel Radio System RequiredNot Compatible with AVC-Equipped ReceiversContents:1 piece
Genuine HT spare/option part. 5 cells, 6 volt, cell size Sub-C. More applications on request.Dimensions: approx 112 x 46 x 23 mmContents:1 piece
Genuine HT spare/option part.Fits all Carson / Smartech 2WD buggy and monster cars like UNOMonster Truck AttackSuper AttackAttack EvoComancheCRT, CPTGas Blaster...The brake cam bushings are replaceable.Contents:1 piece
Wheelbase 535 mm
Genuine FG spare/option part. Plastic Rammer for fixing the front body mounts for the Audi RS5.Dimensions:Length: 125 mmWidth: 390 mmContents:1 piece