y0203 Shaft seal conversion kit for Losi 5ive-T and Mini differential
€6.90
Available
Product information "y0203 Shaft seal conversion kit for Losi 5ive-T and Mini differential"
Shaft seals are better than o-rings for sealing fast rotating shafts.
The set includes the parts for retrofitting all three differentials of the vehicle.
Installation can be done only in the differential housing. Unfortunately the corresponding bore in the differential gears is machined differently, so you have to stay with the O-ring for that application.
Set includes:
- Three pieces shaft seal 10 x 15 x 3 mm
- Three pieces shim 15 x 21 x 0.2 mm
- Three pieces shim 10 x 20 x 0.3 mm
- Five pieces washer 10,5 x 20 x 2 mm
Login
Customers also bought
Genuine ATOP spare/option part. Fits the rear plastic gearbox on all cars from the 5ive series and as spare part the ATOP gearbox AT-5T016. Stock size bearings are used.Contents:2 pieces
Genuine Atop spare/option part. Colored fuel hose with clams and suction tubesArea Rc High flow fuel line kit.This high flow fuel line kit fits the HPI Baja series and the Losi 5ive-T/B and Mini. It may fit other large scale cars as well.The kit comes with 6 pieces of fuel line clips and 2 assembled plastic fittings. Those fittings cannot be compressed by the tanks fuel line grommet, so the inner diameter remains constant which improves fuel delivery to the carb.Fuel line dimensions:Length: 1mInside diameter: 3 mmOuter diameter: 6 mmAvailable colors: AT001/01 - YellowAT001/02 - RedAT001/03 - BlueAT001/05 - GreenIncludes:2 x Assembled plastic fittings6 x Fuel line clipsTygon fuel line
Sintered steel clutch for Zenoah and many other rc-car engines from 23 cm³ to 32 cm³. incl. clutch spring!Note: The sintered steel clutch needs a break in period of at least half an hour run time after their first installation. Only then the clutch surface reaches the desired grip and provides the necessary friction. After that the clutch will show consistent operation and extremely low wear!With 80 grams the weight of the clutch is about the same as the usual OEM clutches.As with all non-adjustable clutches a periodic monitoring of the clutch spring is recommended. By changing the spring, it is also possible to match your car to the track conditions, i.e.: the harder the spring, the higher the stall speed of the clutch.If not on hand, for installation of the sintered steel clutch a clutch spring, the Zenoah screw set # 7318 and the original Zenoah clutch mount # 7315 are required!
Genuine HPI spare/option part. Content:1 piece
Genuine HPI spare/ption part.For HPI Baja 5BThe Hot Bodies off-road tyre range has expanded to fit the 1/5th scale Baja 5B from HPI!Now available for the Baja buggy are the awesome Double Blade 2WD front tyres, as well as the Proto and Khaos rear tyres!Use HB Baja tyres to put the hurt on the opposition!White compound is medium, great for practice and all-around use.Blue compound is firm for high-bite tracks.Contents:2 tires
Customers also viewed
Race ported top end set for Zenoah G320 engine.The SPEED TEC EXPERT genuine Zenoah G320 race ported top end set is optimized for performance with sophisticated craftsmanship and when accurately installed - guarantees, besides greatly increased performance, excellent workmanship and stamina. SPEED TEC EXPERT version modifications: Cylinder: Adjustment of compressionEnlarged portsFuel management milledModified exhaust and intakeTransfer port covers:Glued and ready for use Piston: Weight reducedSkirt shortenedOil ringsPiston above and below piston ring tapered and piston dome groundSet includes the following parts: CylinderPistonPiston ringCylinder foot gasketPiston pinPiston pin clipThrust washer for needle bearingCover for transfer portTo achieve the optimum performance gain of a SPEED TEC EXPERT top end set, we recommend the use of a tuned pipe ().
High quality flexible fuel line in your choice of blue, red, yellow, orange and green. Size:Length: approx. 1 meterOuter diameter: approx. 6.3 mmInner diameter: approx. 3.2 mmDiameters are 100% identical to the Zenoah Tygon hose #7352!
Genuine ATOP spare/option part. Upper rear camber rods with guide bushing set and with pivoted steel ball joints right/left thread and locknuts for 5ive-T. Balls with 6 mm hole, adapter bushings for 5 mm screws, shortest distance between mounting points (center/center) 140 mm. Contents:2 pieces
Original Zenoah 32 cm³ Rebuilt kit Top quality with Zenoah warranty!Set includes the following parts: CylinderPistonPiston ringCylinder foot gasketPiston pinPiston pin clipThrust washer for needle bearingCover for transfer portAttention: For the assembling of the covers enclosed please use the HT-flange sealer y804 and pay attention to the assembling instructions enclosed.Please note:It is recommended to use a gasket sealer with every gasket on an engine. This gives better sealing anda longer lasting gasket. We also recommend:y0804 HT-flange sealer 518 y0994 Marston sealery0807 MD-Sil RTV silicone sealer
You can select the tyre hardness above: - Hurrax HX100 extreme Grip Medium 175/70 mm tyre and - Hurrax HX400 extreme Grip Soft 175/70 mm tyre Please select which tyre you prefer. You also have the option of having the tyres delivered ready glued for an additional charge. Please click if you want to have the tyres ready glued! HURRAX extreme is one of the most successful tire in large scale off-road racing and specifically designed for astro turf and solid ground. With more than 700 (!) differently designed, closely spaced lugs and the 70 mm wide tread it is reasonably wear resistant and provides optimal grip with good side traction. If this - i.e. on the front axle - is not desired, you may cut the lugs at the tires outer edge to reduce cornering grip. This can be easily done with a small side cutter or strong nail scissors. In order to reduce the edging in the tire on the front axle.This makes a tire less aggressive during cornering and changes the cars behavior towards understeer. It becomes depending on the track conditions (i.e. wet!) a lot more drivable.An optimal vehicle setup can often be achieved by running already used HURRAX extreme tires on the front and new ones on the rear axle.This is especially true for 2WD models. Dimensions:External diameter approx. 175 mmInner diameter approx. 130 mmWidth approx. 70 mmWeight: one glued tire on Hurrax rim: 470 gramsDue to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable. GRP off-road disc rim for tires with approx, 132 mm inner diameter.The closed disc rim features reinforcement ribs on the backside and a protective collar around the wheel nut seat.Dimensions:for tires with an inner diameter of approx. 132 mm and approx. 70 mm widthand an outer diameter of approx. 180 mm (like i.e. GRP / Gandini tires)Weight approx. 172 gramms
Genuine Losispare/option part. Mechanical brake for retrofitting in an electric powered Losi 5ive-B or 5ive-T 2.0. An additional servo and a 3-channel remote control are required.If you run the maximum operating voltage approved for an ESC, there is a risk - especially in large scale cars - that under certain circumstances the reverse currents generated by the motor when braking will destroy the esc.For this reason, we recommend using a mechanical brake (as with gas powered vehicles).Please note that Reverse is no longer possible with this configuration!In the ESC settings, you must select the Forward/Brake operating mode. The brake by the controller must be deactivated or set to the lowest possible value. For this job a program card suitable for the ESC is usually required!Set includes: TLR252011 TLR Brake Disc, Pad and Screw Set 5ive-B LOSB3230 Losi Brake Cams & Bushings 5T, TLR 5ive-B and Mini LOSB5901 Losi Throttle/Brake Linkage Set 5T, TLR 5ive-B and Mini Servo mount for throttle / brake servoLosi Servo HS901T Contents:1 set
