y1420 Diff Locker for Losi 5ive-T/2.0, 5ive-B and Mini

Genuine HT spare/option part.Alloy case conversion kit for Smartech / Carson 2WD and FG 2WD large scale cars .Comes complete as shown with reinforced differential tube, sealed bearings, installed needle bearings, shims, screws and o-rings.The scope of supply for FG:4 x Countersunk screw M4 x 8 mm2 x Shims 8 x 20 x 0,10 mm2 x Lenticular flange head screw M3 x 10 mm2 x Washers 3,2 mm2 x Gasket for DiffThe scope of supply for Smartech:4 x Countersunk screw M4 x 8 mm4 x Shims 8 x 20 x 0,10 mm8 x Shims 5 x 17 x 0,10 mm2 x Lenticular flange head screw M3 x 10 mm2 x Washers 3,2 mm2 x Gasket for DiffContents:1 set

Genuine HT spare/option part.Alloy diff case conversion kit for FG 2WD cars and 4WD large scale cars, fits front or rear axle. You need two sets to do a complete car.Comes complete as shown with sealed bearings, installed needle bearings, shims, screws and o-rings.Please note:The differential comes unassembled, we recommend assembly tool #8505 for bevel gear installation.Contents:1 piece

Alloy case conversion kit for Carson Gas Devil 4x4 (Smartech Titan) only, can be used for all differentials.Comes complete as shown with sealed bearings, installed needle bearings, shims, screws and o-rings.

Genuine HT spare/option part. Alloy case conversion kit for Carson Gas Devil, Carson CRT 4x4, Conrad Hell Devil and Smartech Titan, can be used for the center differential onlyComes complete as shown with sealed bearings, installed needle bearings, shims, screws and o-rings, diff tube and the parts for the slip adjustment device.Adjustment of the locking effect:The adjusting screw which presses on the bevel gear axle and the thrust bearing regulates the locking. This causes friction between the bevel gear and the diff. housing. The locking effect can be adjusted between 0% and about 90%. The adjustment has to be changed according to track surface and dirt accumulation.Loosen the locking effect completely if the track is wet.Contents:1 piece

The conversion kit includes all parts needed for a conversion from a standard plastic differential to an adjustable alloy differential.Please note: The differential comes unassembled, we recommend assembly tool

Genuine FG spare/option part. Through the enlarged locking mechanism pressure is produced on two bevel wheels. Therefore we gained a better distribution of compression and an even more sensitive adjustment. Suitable for all 1:5 models and 1:6 Race-Trucks. The set includes all parts necessary to retrofit the alloy differential 8485/05.Contents:1 set

Genuine FG spare/option part. This conversion kit includes all necessary parts to convert the alloy differential 8483/05 or 8485/05 to a double self-locking differential gear.Contents:1 set

Genuine FG spare/option part. Conversion kits for the alloy differential gears 8500/05 and 8501/05.You achieve an even more effective locking effect through the use of these conical friction surfaces.Contents:1 set

Genuine FG spare/option part. The conversion kit includes all parts needed for a conversion from a standard plastic differential to a non-adjustable alloy differential.Content:1 set

Genuine FG spare/option part. Conversion kit for standard differential. Precise, solid and reliable, for use at competitions.Suitable for Off-Road Buggy 4WD RTR, Off-Road Beetle 4WD RTR and Monster/Stadium models 4WD RTR.Contents:1 set

Genuine FG spare/option part. This conversion kit includes all necessary parts to convert the alloy differentials 8483/05 or 8485/05 to a quadruple self-locking differential gear.Contents:1 set

Item N° 06407/05 Mini pin M / OR tires, glued, white, 2 pcs.Spare part for the Leopard 2010 2WD/4WD versionThe new FG Mini Pin tires are designed for harder grounds. They grant the model a lot of stability and tremendous grip in curves. 153 mm diameter64 mm wideThe version M is suitable for cooler temperatures lower than 20°, die version H is for temperatures over 20°. The tires are glued ready to run on the widened 1:6 wheels.These wheels are suitable for the FG Marder, Beetle, Off-Road Buggy and the monster models. Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable.

Genuine GPM spare/option part. Servo mount for Losi Super Baja Rey / Rock Rey made by GPM, machined from high grade 6061-T6 aluminum. The mount is tweak-resistant and improves steering precision.Contents:1 piece

Item N° LOSB2972 Rear Springs XXX Rate 5T, 2 pcs.Measures:Length: 130 mmWire thickness: 2,5mmInna diameter: 32,6 mm

Genuine HT spare/option part. This machined aluminum servo adapter allows easy installation of servos with a 69 x 18 mm mounting bolt pattern (for example Orange-Power, S8203) in vehicles / radio plates which provide a 75 x 18 mm mounting bolt pattern (for example Losi 5ive-T, Mini WRC, HPI Baja 5 series cars, many FG cars).The use of this adapter servo will neither tilt the servo, nor does it change installation height. Scope of delivery:1 x Servo mount adapter2 x Socket head cap screws 3 x 20 mm2 x Socket head cap screws 3 x 12 mm2 x Shim ring 3,2 mmContents:1 piece

Unfortunately the Fox body is no longer available!The original DBXL-E set the world on fire as the go-to vehicle for large scale bashers and enthusiasts alike. Its agile handling, out of the box speeds and durability make it a fan favorite. Now the Losi® DBXL-E 2.0 continues to build on the legendary status! Known worldwide for their dominance in the gas 1/5 market, especially with the 5IVE-T 2.0, Losi has built the DBXL-E 2.0 to be cleaner and easier to use, but with performance and speed that outruns the competition. At home in any environment from dirt to pavement, wet or dry, especially with its 4WD drivetrain with larger 5mm drive pins, the desert buggy makes sure all the power is put to the ground. Drivers stay in control with a DX3 transmitter, a Spektrum SR6100AT 6 Channel AVC® Telemetry Surface Receiver, and scale-to-size Maxxis Creepy Crawler LT tires. This desert buggy features all the technological advances drivers demand including the Spektrum Firma® 160 Amp Brushless SMART ESC and Spektrum Firma 4-Pole 780Kv Brushless Motor allowing you to hit 50+ MPH with an 8 cell LiPo battery. Finally, the DBXL-E 2.0 has a Losi and Fox Shox race-inspired motorsports themed livery for that true off-road look. You get all this and more from the brand that represents the pinnacle of performance. Spektrum Firma® 160 Amp Brushless SMART ESCThe ESC is waterproof, completely programmable, and comes pre-wired with a high-current IC5 connector. The ESC will work with most sensorless brushless motors and is Li-Po and Ni-MH compatible. The SMART technology provides information like battery voltage, RPM, RX pack Voltage, and Speed directly from the ESC when used with the Spektrum Dashboard app. 50+ MPH Spektrum Firma 4-Pole 780Kv Brushless MotorThe brushless ESC and motor provide wicked power with an 8s LiPo battery (not included) that will blaze speeds of 50+ MPH. Spektrum S906 1: 5-MetallgetriebeservoNeues 30-kg HV Hi-Torque Metallgetriebe-Servo. New Chassis Braces In addition to the chassis stiffening plate, we have also added an additional electric specific rear chassis brace that goes all the way up to the center diff mount to increase the rigidity of the chassis. Updated Front and Rear BulkheadsThe front and rear bulkheads have been updated to match the new gearboxes designed for the DBXL-E 2.0. Two additional mounting locations were added to the side of the bulkheads to keep the gearboxes from rocking up and down under acceleration and braking. This provides a more stable drivetrain, and increased overall durability. Aluminum Center Diff CupReturning from the original DBXL-E is the aluminum diff cup used in the center differential. Today"s brushless motors produce so much power, that you need to have the added strength and durability in the center diff that only an aluminum diff cup can provide. New Shocks with Laser Etched FOX Logo Shock CapsNew shock bodies with a lower aluminum cap that allows for easier maintenance of the shock seals for improved performance. Sometimes, it is about the details. New upper shock caps with laser etched FOX logo set off that race inspired look. MAXXIS Creepy Crawler Tires with Authentic Bead Lock WheelsGenuine MAXXIS creepy crawler tread pattern tires provide added traction and offer extra control so you can stop, turn and swerve like a pro. Have confidence your tires will never come unglued and make tires changes a breeze with authentic bead lock wheels. Aluminum Shock TowersWe couldn"t just stop at the shocks. The DBXL-E 2.0 gets all new Aluminum Shock Towers Front and rear with revised camber mounting locations for improved stability and handling. Heavy Duty DrivetrainIncreased the size of the out drives and drive shaft to support a larger 5mm drive pin for increased strength and durability. New Radio TrayAll new radio tray with sealed receiver box. The new radio tray allows for multiple steering servo configurations. Can be run as a single servo, or updated to run dual steering servos for maximum steering performance. New ESC MountTo create space for the larger battery trays, we needed to find a new home for the ESC. The ESC has been relocated to a mounting plate off the center differential. This allows for optimal weight distribution within the car, while increasing the air flow over the top of the ESC for better running performance. New Race Themed LiveryNew Fox Shox race inspired Motorsports themed livery for that true off-road look, along with an awesome Losi flame design trim scheme. Waterproof ElectronicsThe DBXL-E 2.0 is loaded with waterproof electronics including the receiver, servo and ESC. Everything is sealed against the elements allowing you to splash in the rain, spin in the mud and make tracks in the snow. It"s full-throttle freedom to run anytime, rain or shine LED Light BarThe roof mounted LED Light bar from the original DBXL-E returns to continue lighting the way for endless adventures. Spektrum DX3 Radio SystemThe Spektrum DX3 radio system offers advanced features like AVC control, a 3-position throttle limiting switch and travel adjust. It features exclusive DSMR® technology for superior range, response, and interference resistance. It's also fully compatible with the Smart telemetry potential provided by the vehicle's installed Spektrum Firma Smart 40A ESC/receiver, and has a convenient voltage level indicator for any Spektrum Smart batteries! The Full-Throttle Freedom of AVC® TechnologyThe receiver's built-in AVC® (Active Vehicle Control®) traction control system works behind the scenes, making hundreds of throttle and steering adjustments per second, so more of the motor's power is translated into ballistic speed and acceleration instead of just flying dirt. The patent-pending AVC system adds a level of performance that simply cannot be found with any vehicle from any manufacturer other than Horizon Hobby. Like traction control in your full-scale vehicle, you can activate or deactivate the system on the fly and adjust the level of stability based on driving conditions. Any RC vehicle can go fast and with AVC you can go faster while maintaining optimum stability in all driving conditionFeatures Spektrum Firma® 160 Amp Brushless SMART ESC Spektrum Firma 4-Pole 780Kv Brushless Motor Spektrum DX2E Active radio system with AVC® and new SR6100AT Receiver Spektrum S906 1/5th scale metal gear servo Waterproof Components Aluminum Shock Towers Aluminum Center Diff Cup New Radio Tray designed for use with single or dual steering servos. New Heavy Duty Drivetrain with 5mm drive pins New Electric Chassis specific chassis braces for increased durability and strength New ESC Mount Pinned Center Outdrive Cups New Gearboxes for improved drivetrain strength and stability New Steering Rack with helical servo saver design Updated Front and Rear Bulkheads Maxxis Creepy Crawler LT Tires Losi and Fox Shox race-inspired Motorsports themed livery Laser Etched FOX Logo Shock Caps Roof-mounted LED bar Dimensions Height: 317 mm Length: 844 mm Width: 495 mm Weight: 9,8 kg