21 products found for "y1064"

rc-car-online - Home

y1064 Cable ties, black, 202 x 2.5 mm, 20 pcs.

For the secure installation of driveshaft boots.

€3.90*

y1564 XT90 Charging cable

Genuine HT spare/option part.Charging cable for batteries with XT90 connector, length approx. 30 cm, silicone insulated cable with gold-plated connectors.Contents:1 piece

€8.90*

y1067 Walbro WT668C carburetor

Genuine Walbro spare/option part.The Walbro WT668C carburetor fits all Zenoah, Chung Yang (CY), Losi, HPI und PT (Smartech/Carson) engines from 23cc up to over 30cc. The Walbro WT668C features an integrated choke with lever and a throttle shaft linkage lever.The WT668B is also available with ball-raced throttle shaft under part number # y0036/04 Ballraced tuning Walbro WT668B carburetor The higher quality alternative is the Walbro WT603B, also with choke. Contents:1 piece

€69.90*

This product is no longer available.

y1004 Driveshaft boots for ball drive + dogbones

Genuine HT spare/option part. Protect ball drive as well as cardan drive against dirt. For FG and Carson ball drives, fits standard dogbones as well.Contents:2 pieces

€8.90*

y1046 Clemps for hydraulic brake lining 4 mm

Genuine rc-car-online spare/option part. Clemps for hydraulic brake linings with a outside diammeter of 4mm. e.g Colari, Magura II and Mecatech.Contents:8 pieces with mounting screws

€9.50*

y1068 HT Aluminum shock tower set 2WD

Genuine HT spare/option part.Set includes shock tower Marder y1032, fits Marder, Beetle, Pajero, Monster Beetle Aluminum bulkhead brace for y1031.Contents:1 set

€69.90*

y1044 Y-connector for hydr. brake system - 1 pce

Y-connector for all hydraulic brake linings with a outside diammeter of 4mm. e.g Colari, Magura II and Mecatech.

€14.90*

y1604 SPEED TEC CRANK Team-Edition Zenoah G290 Tuning engine

The SPEED TEC CRANK genuine Zenoah engine is optimized for performance by hand with sophisticated craftsmanship and guarantees, besides greatly increased performance, excellent workmanship and stamina. SPEED TEC Team Edition version modifications: Cylinder & case:Adjustment of compression; enlarged ports, fuel management milled, machined and polished exhaust, intake is flow-optimized the case is specially matched with enlarged and flow-optimized cross section towards the ports Piston:Transfer port area optimized for flow and polished, weight reducedand the piston-roof is polishedCrankshaft:is adjusted, aligned and balancedFlywheel and ignition:Latest SPEED TEC CRANK SV ignition system for rc-car race engines with air baffles, a special balanced 62 mm diameter flywheel, modified ignition coil mount and special ignition system allows for the extremely fast revving of the SPEED TEC team edition engine and guarantees a significantly improved performance.The machined and more than 30% lighter than stock CRANK flywheel with fins on both sides contributes to the optimized engine cooling.Gaskets:Premium quality gaskets installed. Cylinder gasket installed using elastic gasket sealer.Isolator:Special matched and raised insulator Attention! We recommend to run exclusively fully synthetic 2-stroke engine oil, like y0813 Motul 800 racing oil.

€949.00*

y1034 HT Aluminum front suspension for FG Off-Road Buggy 2WD, set

The sets include complete front bulkheads A + B with brace, upper (adjustable) and lower a-arms and shock tower.Please note: the hinge pins are not included, you will use the pins from the stock suspension!The sets include:Item N°Name:y1027HT Aluminum a-arm 2WD, front uppery1026HT Aluminum a-arm 2WD, front lower, one-piecey1028HT Aluminum front bulkhead A for 2WDy1030HT Aluminum front bulkhead B for 2WDy1036HT rose joints with conical spacersy1029HT aluminum droop stopsy1035HT Aluminum shock tower Off-Road Buggy 2WDy1031HT Aluminum bulkhead brace for 2WDUnit prices: 387,10 EURFits FG Off-Road Buggy 2WD.This front suspension can be used on a FG Monster Beetl 2WD as well, however some new holes must be drilled into the shock tower for this application.

€339.00* €387.10* (12.43% saved)

VOLZ-Servo, y1060 - 1pce. -Special offer-

Version 220 for steering and throttle/brakeOriginal price: 266,80?Gears: Metal - Steel output shaftBearings: 2x ball bearingWeight: 72gVoltage: 6,0 VoltsTorque: 220 Ncm Speed: 0,11 s. 40ºDeflection: 2 x 45º

€179.90*

y1464 MadMax SUPER GRIP 170x80/x60 replacement wheels

The MadMax SUPERGRIP tires have been designed especially for use on tarmac. Even on fine-pored tarmac your car will still find enough grip! (As you can see in our video).On most 1/5 and 1/6 cars the best combination is the use of 60 mm wide front and 80 mm wide rear tires. The Losi 5ive-T Mini should run 60 mm wide MadMax SUPERGRIP tires all around, because the 80 mm wide SUPERGRIP tires are a bit too wide for the Mini body shell.The 80 mm wide MadMax tires are reinforced on the inside of the carcass with a special cross pattern in the tread section and ribs in the outside shoulder.MadMax SUPERGRIP tires are available in the following compounds: (embossed marking on the inside shoulder!)Breite:Soft:Medium:60 mm y1464/01y1464/0280 mm y1464/03y1464/04For running an rc-car on tarmac, the following recommendations apply:The dirtier the track or the colder the weather, the stickier (softer) the rear tires should be.A note for the front tires: 2WD cars should run slightly harder tires in front than in rear.On 4WD cars the same compound front and rear is usually a good choice!Of course, like in full scale motorsport it also applies to the MadMax SUPERGRIP tires that the softer the tire the higher the wear. The medium compound tire lasts significantly longer than the soft version!The MadMax SUPERGRIP has a special on-road tread. These tires have excellent grip even after eating up the tread and can be used after that for a long time as slicks! Some off-road tires knowledge can be found here!

From €29.90*

Details

10642 FG Alloy differential bearing carrier, l/h - 1 pce

Spare part for F1 gear drive

€39.90*

y1024 MadMax OVER LANDER 170x80/x60 complete set for Traxxas X-MAXX 4x4 with adapter

Offerset:1 Pair MadMax Over Lander front tires 170x60 mm1 Pair MadMax Over Lander rear tires 170x80 mm1 Pair MadMax front rims 60 mm1 Pair MadMax rear rims 80 mm1 Pair MadMax front inlays 60 mm1 Pair MadMax rear inlays 80 mm2 Pairs / 4 pieces adapter TT1020/01OVER LANDER 170 x 80 mm and 170 x 60 mm tires with reinforced orange beadlock rings on black rims. Were designed the OVER LANDER as all-terrain tires that can be used on virtually all surfaces because of its tightly attached lug tread pattern When a terrain includes sand, gravel and grass, the Overlander is the right choice! It can even be used on partially paved tracks!Of course, the OVER LANDER allround tire will not make special purpose tires like the TARMAC BUSTER,BIG DIGGER or CROSS BOND obsolete. Due to the extreme load created by the MadMax OVER LANDER tires the rim was optimized again with a reinforcement ring.The tires are fitted with a special rigid insert, which can handle the cornering forces and maintain the tires shape even on heavy cars.The set consists of two each front and rear tires, including tire inserts and MadMax EXTREME rims and 4 pieces adapter wheel nuts TT1020/01. We recommend to check the beadlock screws after the run. Dimensions:Outer diameter: 170 mmFront tire width: 60 mmRear tire width: 80 mmReinforced 24 mm hex wheel driveThe video shows the 18 mm square drive version. Also available with 24 mm hex. Some off-road tires knowledge can be found here!TT1020 Top Tuning Adapter wheel nutGenuine TopTuning spare/option part.These adapter nuts, manufactured from billet 7075 aluminum allow for easy and precise installation of all MadMax, HPI and Losi tires and rims on the Traxxas X-Maxx. For the best result possible, nut and adapter are manufactured as a one-piece unit.It should be noted that the wide rims can be used on the rear axle only. On the front axle they would limit the steering angle by grinding on lower a-arm and steering rod.Traxxas has microencapsulated the wheel shafts of the X-Maxx to secure the wheel nuts. Like any thread locking compound this is not for eternity. After several tire changes the use of a normal screw locking compound is advised, we recommend it "y0113 / 01 medium strength".The dimensions of the nut are specifically designed for use with MadMax, current HPI and Losi rims. Rims from Losi 5ive have slightly different dimensions in the hub area. This is meaningless on the large LOSI or HPI wheel adapters. With the smaller and shorter wheel nut thread of the X-Maxx wheel shafts you cannot compromise. Therefore there are also special nuts for the Losi rims/wheels available at our options menu.However, somewhere in the past, the injection moulds for the HPI rims were slightly modified in the hub area. As part of that job the bore diameter has probably been slightly increased. Therefore, the use of older rims in combination with the adapter nuts makes it necessary to increase the rim bore a little bit.Due to repeated requests for use: these wheel nuts replace the stock wheel nuts when installing the wheels!Contents:4 pieces

From €139.90*

Details

10644/01 FG Alloy wishbone mounts Ø4

Genuine FG spare/option part. Solid alloy wishbone mounts with 4mm boring for the FG Formula 1 Sportsline and Competition models.Six pieces per car are required.Contents:2 pieces

€35.10*

10640 FG Alloy rear bulkhead l/h F1 Comp. - 1 pce

Spare part for F1 gear drive

€106.50*

10644 FG Alloy wishbone mounts M4

Genuine FG spare/option part. Solid alloy wishbone mounts with M4 thread for the FG Formula 1 Sportsline and Competition models. Six pieces per car are required. Contents:2 pieces

€35.10*