y1067 Walbro WT668C carburetor
Product number:
y1067
EAN:
4058575048152
Product information "y1067 Walbro WT668C carburetor"
Genuine Walbro spare/option part.
The Walbro WT668C carburetor fits all Zenoah, Chung Yang (CY), Losi, HPI und PT (Smartech/Carson) engines from 23cc up to over 30cc.
The Walbro WT668C features an integrated choke with lever and a throttle shaft linkage lever.
The WT668B is also available with ball-raced throttle shaft under part number # y0036/04 Ballraced tuning Walbro WT668B carburetor
The higher quality alternative is the Walbro WT603B, also with choke.
Contents:
The Walbro WT668C carburetor fits all Zenoah, Chung Yang (CY), Losi, HPI und PT (Smartech/Carson) engines from 23cc up to over 30cc.
The Walbro WT668C features an integrated choke with lever and a throttle shaft linkage lever.
The WT668B is also available with ball-raced throttle shaft under part number # y0036/04 Ballraced tuning Walbro WT668B carburetor
The higher quality alternative is the Walbro WT603B, also with choke.
Contents:
- 1 piece
Login
Accessories / Spare parts
TURBO-TWIST, 325 mm long screw driver in top quality. Allows you to set the carburetor on almost any 1:5 / 1:6 model also with a mounted body shell.On most models, you have to adjust the motor with this screwdriver does not even stoop.Caution:May differ from picture!
Customers also viewed
Alternative: Walbro 603B also with choke. But with better manufacturing quality!The Walbro WT668B carburetor fits all Zenoah, Chung Yang (CY), Losi, HPI und PT (Smartech/Carson) engines from 23cc up to over 30cc. The Walbro WT668B features an integrated choke with lever and a throttle shaft linkage lever.The WT668B is also available with ball-raced throttle shaft under part number # y0036/04 Ballraced tuning Walbro WT668B carburetory0036/04 Ballraced tuning Walbro WT668B carburetorWith dual ball bearings on the throttle shaft. Two sealed bearings 2RS type (3/16" x 5/16" x 1/8") shielded by two steel plates (5 x 8 x 0.3 mm). High quality processed and optimized for racing use! The soft stock screw holding the throttle lever has been replaced with a high strength Allen key screw. Since all screws on the carb are imperial sized, so is the key for this screw. A corresponding bit is included in our tool set y0785, or you can use Allen key wrench y0037/03 as well.The Walbro WT668B carburetor fits all Zenoah, Chung Yang (CY), Losi, HPI und PT (Smartech/Carson) engines from 23cc up to over 30cc. The modified Walbro WT668B features an integrated choke with lever and a throttle shaft linkage lever.The Walbro WT668B carburetor is also available in a standard version under part number # y1067 Walbro WT668B carburetor.
Genuine Zenoah spare/option part. Replacement part fits Zenoah G320RC.
Item N° 69251 Plastic front axle housing right 4WD, 1:5, 1pce.
Item N° s23001/01 Pressure spring for Recoil starter set for PT 23/28, 1 pce.Pressure spring for the recoil starter PT 23/28 engine.
The FG Off-Road Buggy WB535 is presented with a longer wheelbase and a pleasant design. All-wheel-drive, completely mounted ready-to-drive, combined with the open Off-Road Buggy body shell with metal roll cage and gigantic Off-Road rims with low-profile knobbed tires.The body shell is standard unpainted. Equipped with a 26cm³ engine the Off-Road Buggy is aggressive and also a tremendous jumper. The 35 mm wheelbase extension results in a higher tracking stability. You can select the car with complete RTR-equipment from the options menu. RTR-equipment RTR = Ready to Run. The RTR version comes ready to use with the 2,4 GHz rc-system already installed. Transmitter: Reflex Wheel Pro III 2,4 GHzReceiver: Mini BECHigh power servo for throttle and brakeLargescale servo for steeringTx-battery, rx-battery Equipment of the modelAngled 4 mm, alloy chassis, completely covered belt drive, two differential gears at front and rear axle with hardened bevel gearwheels, closed front axle housing, front bumper, double wishbones at front and rear axle, gear brake, adjustable right/left thread rods at the track rods and at the front and rear wishbones, front uprights with steering stops, gearwheels made of case-hardened steel, completely ballbeared, four large-volume oil-pressure shock absorbers, receiver box.According to side rails and the closed body shell the Off-Road Buggy is almost protected against dirt from underneath. The two-parts body shell is made of polycarbonate, the rear spoiler is made of impact resistant polyamide. Driver´s coverage and roll cage parts are made of aluminum. The giant low-profile knobbed tires are glued on black rims.The model is equipped with a powerful 26cm³ (series) combustion engine with ready-for-use oiled air filter. The engine runs with normal 2-stroke petrol-oil mixture (available at every patrol station). The tank filling of 0,7 litres enables you to run your model around 45 minutes. With the installed pull-stat system the engine can be started without any difficulties. HT-Edition? HT-Edition means: this version comes with a big set of spare / option parts included. Steel pinions - Non-standard sizesEach of two different ratios are supplied with.Modul: m=1,5Value: 62,60 EURAlloy engine mount bigCNC machined alloy engine mount, direkt replacement for the stock plastic part, heat and tweak resistant. They come with all necessary hardware included. Value: 64,95 EUR Alloy spur gear carrierUse for 39T - 44 teeth spur gears.Value: 39,90 EUR Ball bearing set, sealed, set of 14The seal rings on sealed ball bearings keep dirt and dust out of the bearings. They are therefore particularly suitable for use in dirty and dusty environments.Value: 59,90 EURTotal value: 227,35 EURThe RTR version is delivered with installed and preset radio control system and rechargeable batteries. To complete the non-RTR version all popular servos and radio control systems are suitable.The pictures may display the car with some optional items which are not included, like bed-mounted rollbar, lights, front bumper or mirrors. These items can be added in the drop down menus.Measures:Length: 770 mmWidth: 480 mmHeight: 280 mmWheelbase: 535 mmWeight: 10,8 kg