DYNE1240 Dynamite Large Scale Safety Kill Switch
€39.99
Currently unavailable
Product information "DYNE1240 Dynamite Large Scale Safety Kill Switch"
Key Features:
- Kills your 2-cycle gas engine on command, loss of radio signal, low battery, or total battery power loss
- Comes ready to install no soldering required
- Optically Coupled to isolate your ignition system from your radio system
- Built-in LED for easy-to-spot operational status
- 3-Channel Radio System Required
- Not Compatible with AVC-Equipped Receivers
Contents:
- 1 piece
Login
Accessories / Spare parts
Genuine TT spare/option part.Spare part for Killswitch TopTuning 0990 or Dynamite 1240. Also suitable for other projects at your own discretion.Operating voltage 2.1 Volt, approx. 15 mA2-pole connection cable with PVC insulation and 24 AWG/0.2 mm² cross-section, length approx. 180 mm.Contents:1 piece
Genuine TT spare/option part.Spare part for Killswitch TopTuning 0990 or Dynamite 1240. Also suitable for other projects at your own discretion.2-pole connection cable with silicone insulation and 22 AWG/0.32 mm² cross-section, length approx. 80 mm.Contents:1 piece
Genuine TT spare/option part.Spare part for Killswitch TopTuning 0990 or Dynamite 1240. Also suitable for other projects at your own discretion.3-pole connection cable with PVC insulation and 24 AWG/0.2 mm² cross-section, length approx. 220 mm.Contents:1 piece
Genuine TT spare/option part.Spare part for Killswitch TopTuning 0990 or Dynamite 1240. Also suitable for other projects at your own discretion.Plug-in mount for front panel installation, requires 8 mm diameter mounting hole.Contents:1 piece
Genuine TT spare/option part.Spare part for Killswitch TopTuning 0990 or Dynamite 1240. Also suitable for other projects at your own discretion.Set with 2 each red and black jumpers for 2.5 mm contact spacing.Contents:4 piece
Customers also bought
To ensure the required cooling for current 1/5 and 1/6 engines the flywheels have fins on both sides. Therefore the fan housing has large openings on the crankcase side for the required air supply. However, the risk of foreign objects (grass, sand, or even stones!) entering here Is very high! As a result, broken fins on the flywheel occur frequently. This leads to reduced cooling efficiency and - even more critical vibrations from a flywheel which is out of balance due to missing fins. Therefore, this kind of flywheel protection is highly recommended, especially for offroad use. The product video explains the handling in detail! Note:It is essential to thoroughly clean and degrease the crankcase prior to attaching the hook-and-loop tape (OKS2661)!For installation on Chung-Yang and Zenoah engines in FG cars, the crankcase cover must be slightly modified in two places where the engine mount is attached (see Figure 6 and 7). Furthermore the fit of the fabric must be as tight as possible in the region of the layshaft pinion (in front of the differential ring gear!) (see Figure 8).Set includes:Special tailored fabric with sewed on hook-and-loop tapehook-and-loop tape for installation to the crankcaseAdhesive for securing the hook-and-loop tape
New Big-Power muffler with volume increased by about 30%, therefore especially suited for 26 - 32 cc engines.Made from aluminum tubing with a steel manifold this tuned pipe system has a lower weight than comparable units.Pure power over the complete rpm range!Fits Losi 5ive-T and Mini WRC
Genuine FG spare/option part. Splash-proofed receiver box for all merchantable small receivers, suitable for all car models 1:12 - 1:5.Dimensions:Length: upper section 92 mm, bottom 69 mmHeight: 48 mmWidth: 38 mmContents:1 piece
Genuine FG spare/option part. Suitable for all FG touring cars and GT models. Not for Mercedes C291 and Porsche GT1.Contents:1 set
Genuine FG spare/option part. Suitable for all throttle rods.Contents:2 pieces
Customers also viewed
To protect a car from a crash in case the power supply fails is no easy task. The mechanical devices that are used to do the job are either bulky or cause a higher drain from the battery. The failsafe module is a more efficient way.The module controls the battery pack's voltage and takes control of the throttle servo when the voltage goes below 4.7 volts. As an additional feature you can supply a backup battery pack to power the throttle servo in case the main pack falls completely. The failsafe position of the throttle servo is adjustable.
Failsafe unit with adjustable servo position, very low current drain (0.05mA). Excellent value for money!The circuit responds to failure of the control signals. When transmitter and receiver work correctly, the received control pulses determine deflection of the servos; but as soon as control pulses are missing, the circuit lets the connected servo run to a pre-set safety position. Thereby, loss of the model can be avoided.Attention: not compatible with digital servos!
Genuine FG spare/option part. Powerfull servo for 2WD and 4WD 1/5 and 1/6 cars. Ballraced, with metal gears.Technical data:Voltage : 6.0-7.4VSpeed : 0.14s-0.12s/60°Torque: 9-10kgcmDimensions : 40.8 x 20.1 x 38 mmWeight : 56 gContents:1 piece
A small, lightweight electronic module which is connected between the receiver and one servo of your AM or FM radio control system. If the radio control system should fail, the receiver suffer interference, or the voltage of the receiver battery fall to a dangerous level, the servo connected to the unit moves to a pre-selected position, e.g. full brake, and thereby prevents motor damage through over-revving.