32 products found for "clarks_50353021"

rc-car-online - Home

50353021 Support Blocks for the Lightscale Droop Gauge 35 mm rear, 1 pcs.

Item N° 50353021Support Blocks for the Lightscale Droop Gauge 35 mm rear, 1 pce.This is an Alloy Support Block anodized in black colour with 35mm height.The Support Block is manufactured as a rectangle and so can used as a 30mm as well as a 35mm, depending on which side you choose.The front block uses a single point of support while the rear one comes with two of those. Due to this 3 point support it is assured that even a little tweak in your chassis (none of them is 100% straight) will not affect the result of your measurement. Remove the wheels and tyres from your car and put the car onto the support blocks. Ideally the rear block is positioned to the back of car and the front one just where the servo saver is fixed to the chassis. The car is now propped on the support blocks safely and cannot bounce. Please make sure that no dirt or rubber is trapped between the Support blocks and the chassis.Now you can easily and correctly measure the droop of each axle and adjust the cars` tweak.To do so please use the Lightscale Droop Gauge (50835400)The use of Lightscales` Droop Gauge Support Blocks prevents incorrect measurements and therefore is absolutely reliable. Measurements which are done using a flat surface where the chassis is resting on, like you would use in the pits are usually incorrect due to a slightly tweaked chassis because dirt underneath the chassis will falsify the measurement and lead to a irregular setup. The use of Support Blocks which are based on 4 support points will result in the same incorrect results and downgrade the performance of your car which is why we 100% recommend the use of our support block because as racers ourselves we know all about the problems you may face.

€29.90*

50353011 Support Blocks for the Lightscale Droop Gauge front 30 mm, 1 pce.

Item N° 50353011Support Blocks for the Lightscale Droop Gauge front, 1 pce.This is an Alloy Support Block anodized in black colour with 30mm height.The Support Block is manufactured as a rectangle and so can used a 30mm, depending on which side you choose.The front block uses a single point of support while the rear one comes with two of those. Due to this 3 point support it is assured that even a little tweak in your chassis (none of them is 100% straight) will not affect the result of your measurement. Remove the wheels and tyres from your car and put the car onto the support blocks. Ideally the rear block is positioned to the back of car and the front one just where the servo saver is fixed to the chassis. The car is now propped on the support blocks safely and cannot bounce. Please make sure that no dirt or rubber is trapped between the Support blocks and the chassis.Now you can easily and correctly measure the droop of each axle and adjust the cars` tweak.To do so please use the Lightscale Droop Gauge (50835400)The use of Lightscales` Droop Gauge Support Blocks prevents incorrect measurements and therefore is absolutely reliable. Measurements which are done using a flat surface where the chassis is resting on, like you would use in the pits are usually incorrect due to a slightly tweaked chassis because dirt underneath the chassis will falsify the measurement and lead to a irregular setup. The use of Support Blocks which are based on 4 support points will result in the same incorrect results and downgrade the performance of your car which is why we 100% recommend the use of our support block because as racers ourselves we know all about the problems you may face.

€24.90*

50032200 Clarks Upgradekit SDT auf STX

Genuine Lightscale spare/option part. Contents:1 piece

€119.00*

LOS253021 Losi Shock piston kit (TBD), DBXL-E

Genuine Losi spare/option part. Different thickness:1,9 mm2,0 mm2,1 mm2,2 mmContent:1 set

€21.99*

y3021 Stickerbomb "Crunchy"

Genuine HT spare/option part. Universal decals suitable for all body shells. The decals are printed on white film and have to be cut out by yourself.Size (Height x Width):Complete sheet: 300 mm x 410 mmContents:1 piece

€14.90*

305035 Space cover

€6.90*

s23021 Carburetor gasket PT 23/28

Genuine Smartech spare/option part.Please note: It is recommended to use a gasket sealer with every gasket on an engine. This gives better sealing anda longer lasting gasket. Actual product may be of different color. We have no bearing on this since we are not the manufacturer.Please note:It is recommended to use a gasket sealer with every gasket on an engine. This gives better sealing anda longer lasting gasket. We also recommend:y0804 HT-flange sealer 518 y0994 Marston sealery0807 MD-Sil RTV silicone sealerContent:1 piece

€2.90*

2435 FG Body detailing kit McLaren

Genuine FG spare/option part. Content of delivery as shown in the picture.

€11.40*

Details

3021 FG Front bumper CAT-Truck - set

Item N° 3021Front bumper CAT-Truck - setComplete foam bumper, increased protection for chassis and body shell. The bumper comes cut to size and ready for installation.Suitable for CAT-Truck body shell.Length 86 mmWidth 360 mmHeight 58 mm

€29.90*

Details

LOS253023 Losi Shock Cap Set for Super Rock Rey

Genuine Losi spare/option part. Contents:2 pieces

€19.99*

LOS45035 Losi Slicers Rib Tire, DBXL-E 2.0

Genuine Losi spare/option part. Contents:1 pair / 2 pieces

€49.99*

LOS253029/01 Losi Shock Stand Off DBXL-E 2.0

Genuine Losi spare/option part. Contents:4 pieces

€21.99*

3020/02 FG Foam for 3020 and 3021 - 1pce.

Spare foam part for and .Length 93 mmWidth 360 mmHeight 50 mm

€14.40*

Details

LOS253028 Losi Shock Rebuild Kit, DBXL-E 2.0

Genuine Losi spare/option part. Contents:1 set

€19.99*

10353/03 FG Bushing for ballraced pushrod lever - 2pcs.

€9.90*

10353 FG Front pushrod lever, ball raced for F1 Competition

Genuine FG spare/option part.New designed front pushrod lever system for FG F1 Competition chassis. Ball raced damper levers with M5 mounting bolts. Increased shock piston travel. The set includes all parts necessary for the conversion.Contents:1 set

€143.95*