50353011 Support Blocks for the Lightscale Droop Gauge front 30 mm, 1 pce.
Product number:
clarks_50353011
EAN:
4058575032076
Product information "50353011 Support Blocks for the Lightscale Droop Gauge front 30 mm, 1 pce."
Item N° 50353011
Support Blocks for the Lightscale Droop Gauge front, 1 pce.
This is an Alloy Support Block anodized in black colour with 30mm height.
The Support Block is manufactured as a rectangle and so can used a 30mm, depending on which side you choose.
The front block uses a single point of support while the rear one comes with two of those. Due to this 3 point support it is assured that even a little tweak in your chassis (none of them is 100% straight) will not affect the result of your measurement.
Remove the wheels and tyres from your car and put the car onto the support blocks. Ideally the rear block is positioned to the back of car and the front one just where the servo saver is fixed to the chassis. The car is now propped on the support blocks safely and cannot bounce. Please make sure that no dirt or rubber is trapped between the Support blocks and the chassis.
Now you can easily and correctly measure the droop of each axle and adjust the cars` tweak.
To do so please use the Lightscale Droop Gauge (50835400)
The use of Lightscales` Droop Gauge Support Blocks prevents incorrect measurements and therefore is absolutely reliable. Measurements which are done using a flat surface where the chassis is resting on, like you would use in the pits are usually incorrect due to a slightly tweaked chassis because dirt underneath the chassis will falsify the measurement and lead to a irregular setup. The use of Support Blocks which are based on 4 support points will result in the same incorrect results and downgrade the performance of your car which is why we 100% recommend the use of our support block because as racers ourselves we know all about the problems you may face.
Support Blocks for the Lightscale Droop Gauge front, 1 pce.
This is an Alloy Support Block anodized in black colour with 30mm height.
The Support Block is manufactured as a rectangle and so can used a 30mm, depending on which side you choose.
The front block uses a single point of support while the rear one comes with two of those. Due to this 3 point support it is assured that even a little tweak in your chassis (none of them is 100% straight) will not affect the result of your measurement.
Remove the wheels and tyres from your car and put the car onto the support blocks. Ideally the rear block is positioned to the back of car and the front one just where the servo saver is fixed to the chassis. The car is now propped on the support blocks safely and cannot bounce. Please make sure that no dirt or rubber is trapped between the Support blocks and the chassis.
Now you can easily and correctly measure the droop of each axle and adjust the cars` tweak.
To do so please use the Lightscale Droop Gauge (50835400)
The use of Lightscales` Droop Gauge Support Blocks prevents incorrect measurements and therefore is absolutely reliable. Measurements which are done using a flat surface where the chassis is resting on, like you would use in the pits are usually incorrect due to a slightly tweaked chassis because dirt underneath the chassis will falsify the measurement and lead to a irregular setup. The use of Support Blocks which are based on 4 support points will result in the same incorrect results and downgrade the performance of your car which is why we 100% recommend the use of our support block because as racers ourselves we know all about the problems you may face.
Login
Customers also viewed
Item N° 8539 Measuring bench 740mm - 1pce.Allows a measuring of toe-in and adjusting of both sides the same time without changing the side. For an optimal usw you need 2 . Suitable for all FG models except Formula 1.
Item N° 8537 Alloy adjusting disk 145mm - 2pcs.With the alloy adjusting disks you can measure and adjust exactly the toe-in and inclination of front and rear axle. Mount the adjusting disks instead of the wheels. Suitable for FG Formula 1, Race-Trucks and Off-Road models.
%
Ideal work stand with extra wide tripod up to 100 kg. load capacity with excellent stability, even on uneven (!) urface.Specially made support mechanism, individually adjustable width from 115 mm to 375 mm for most RC cars from 1/10 to 1/5 scale. incline from 0 to 90° Quickly folded and loaded For easy storage, as well as for transport completely foldable! (Carrying bag available!)Height adjustment of the support from 635 mm to 1000 mm and inclination from 0-90° Length of the support surface 386 mm Bis zu 100Kg belastbar! Support mechanism continuosly adjustable in width Due to various adjustment options, the Top Tuning CAR STAND offers the optimal possibilities for making adjustments or maintenance work on the RC car. The load capacity and stability are beyond doubt with a load limit of 100 kg and the extremely stable tripod. The up to 90 ° adjustable slant shows your RC car at events and presentations, as well as in your assembly room to its best advantage! 6.5 kg. weight Pivoting bracket Height adjustable from 69 to 104 cm Basic frame is made of steel, painted or chromed Car bracket is made of aluminum and stainless steel A tool holder TT1030/01 is also available as an accessory in our shop selection.
Genuine FG spare/option part. You can check and adjust the inclination of front and rear wheels with the inclination-goniometer. In connection with the measuring bench you can also check toe-in of the rear axle. Suitable for all FG models and also other makes scale 1:8-1:5.Delivery content is only the inclination - goniometer.Contents:1 piece
%
Genuine Mecatech spare/option part. Full-metal hydraulic brake (like the former hydraulic FG brake).The set consists of two complete brake calipers for right and left, and 2 brake units, hydraulic oil and all accessories (see also our pictures) required for installation.One version fits front and rearFits onroad / offroad / monster and stadium cars from FG and othersNo need for alloy uprights!Fits Formular 1 models, Competition, Sportsline
Also suitable for electric models, but in conjunction with aluminum axle y0932
Bleeding instructionsDimensions master brake cylinder:Height: 75 mmWidth: 48 mmDepth: 13 mmContents:1 set
Complete set of screws, nuts and washers for HPI Baja 1/5 vehicles.The set includes a total of 434 screws, nuts and washers in different quantities which are all used on HPI Baja 1/5 vehicles and Carson 1:5 Wild GP Attack.11 sizes of cap head screws9 sizes of CSH screws10 sizes of button head screws4 sizes of set screws2 sizes of washers3 sizes of lock washers3 sizes of self-locking nuts2 sizes of nuts with serrated flange2 sizes of flanged self tapping screwsComes in a high quality 190x170x40 mm assortment box.Contents:Cap head screws in 12.9:20 piecesM3x126 piecesM3x4510 piecesM4x612 piecesM4x1212 piecesM4x2510 piecesM4x306 piecesM4x507 piecesM5x206 piecesM5x306 piecesM5x356 piecesM6x25CSH screws in 10.9:10 piecesM3x2010 piecesM4x1019 piecesM5x1616 piecesM5x206 piecesM5x302 piecesM5x407 piecesM6x14Button head screws in 10.94 piecesM3x1610 piecesM3x303 piecesM4x166 piecesM5x123 piecesM5x302 piecesM5x356 piecesM5x406 piecesM5x452 piecesM6x306 piecesM6x30Grub screws:6 piecesM3x39 piecesM4x46 piecesM4x124 piecesM6x45Washers in Din125:10 pieces3,2x6,8x0,512 pieces4,3x8,7x0,8Safety washers:20 piecesM420 piecesM520 piecesM6Self-locking nuts:10 piecesM310 piecesM415 piecesM5Flanged nuts with serrated base:21 piecesM410 piecesM5CSH screws Torx:10 piecesM4x15 (4,2x16)10 piecesM4x18 (4,2x19)Schneidschrauben Torx mit flanged:10 piecesM2,6x1012 piecesM3x10