Product information "AT-5T013 ATOP Rear camber rods 5ive-T/2.0"
Genuine ATOP spare/option part.
Upper rear camber rods with guide bushing set and with pivoted steel ball joints right/left thread and locknuts for 5ive-T. Balls with 6 mm hole, adapter bushings for 5 mm screws, shortest distance between mounting points (center/center) 140 mm.
Contents:
2 pieces
0 of 0 reviews
Average rating of 0 out of 5 stars
Leave a review!
Share your experiences with other customers.
Login
No reviews found. Share your insights with others.
Genuine ATOP spare/option part. Upper front camber rods with guide bushing set and with pivoted steel ball joints right/left thread and locknuts for Losi 5ive-T. Balls with 6 mm hole, adapter bushings for 5 mm screws, shortest distance between mounting points (center/center) 130 mm. Contents:2 pieces
Genuine ATOP spare/option part. Upper front camber rods with guide bushing set and with pivoted steel ball joints right/left thread and locknuts for Losi 5ive-T. Balls with 6 mm hole, adapter bushings for 5 mm screws, shortest distance between mounting points (center/center) 130 mm. Contents:2 pieces
Genuine HT spare/option part. Abrasion protection for cables, fuel tubes and hydraulic brake lines. Pack with 1 m. Small, for cables from 1.5 to 8 mm diameter.Contents:1 piece / 1 meter
Fits Losi 5ive-T, TLR 5ive-B and 5ive Mini. Content:2 x body clip approx. 1.4 mm wire diameter and 85 mm toal length6 x body clip approx. 1.4 mm wire diameter and 25 mm toal length12 x body clip approx. 2.0 mm wire diameter and 43 mm toal length
Genuine ATOP spare/option part. CNC-machined 6061-T6 aluminum clutch bell holder for Losi DBXL+MTXL. Compared to the stock plastic part the higher strength of the aluminum part ensures secure seat for the bearings, increased dimensional stability at high temperatures and reduced operating temperatures for the bearings due the aluminums thermal conductivity. Larger bearings (12 x 28 x 7) for higher load capacity. Comes with ball bearings and spacer tubes included.It is recommended to use the ball bearings/bushings adhesive (y0113 Thread locking compound).Contents:1 set
Genuine ATOP spare/option part. CNC-machined 6061-T6 aluminum engine mount for Losi DBXL+MTXL. A much safer seating of the engine and the ability to dissipate heat into the chassis plate are the advantages over the stock plastic engine mount.Contents:1 piece This article is identical to the article in the video!
Genuine ATOP spare/option part.CNC-machined from 6061-T6 aluminum by ATOP.Protects chassis plate and transmission case over rough terrain. Also reinforces the chassis plates narrow section in front of the gear case. Thickness: 4 mm, weight: complete 141 grams.Contents:1 set
Genuine Atop spare/option part. Two pieces CNC-machined 6061-T6 aluminum spring perches for Losi DBXL. Direct replacement for the stock part (from set. # LOS 253006).Content:2 pieces
Genuine ATOP spare/option part.CNC-machined from 6061-T6 aluminum by ATOP RC, increase track width for 25 mm and allow for the use of HPI 5T, Losi 5ive-T, 5ive-B and Mini rims. 5 mm o-rings protect against drive pin loss. Set of four inclusive o-rings, drive pins and closed wheel nuts (wrench size 24 mm!).Contents:1 set
Genuine ATOP spare/option part. Rear transmission mount for Losi DBXL cnc-machined from 6061 aluminum by ATOP.Through the use of aluminum, the problem of torn out threads (incl. the front bumper installation) is eliminated. At the same time the chassis section under the transmission is strengthened and the mounting points for the shock towers are reinforced.Comes with all mounting screws included.This is the new ATOP version with the additional mounting points between transmission housing and transmission bracket for a more secure connection of these parts.Old and new versions are fully compatible, regardless of whether they are made of aluminum or plastic. The parts therefore fit all versions of DBXL and MTXL in any combination.However, the use of the additional mounting points requires the new version of both transmission housing and bracket!Contents:1 piece This article is identical to the article in the video!
Genuine ATOP spare/option part. CNC-machined 6061 aluminum transmission case by ATOP, fits front and rear.Service life of ball bearings and ring & pinion will greatly benefit from the increased strength of this aluminum case. Comes with all mounting screws included.This is the new ATOP version with the additional mounting points between transmission housing and transmission bracket for a more secure connection of these parts.Old and new versions are fully compatible, regardless of whether they are made of aluminum or plastic. The parts therefore fit all versions of DBXL and MTXL in any combination.However, the use of the additional mounting points requires the new version of both transmission housing and bracket!Contents:1 piece This article is identical to the article in the video!
Genuine ATOP spare/option part. CNC-machined from 6061-T6 aluminum by Area RC.The big advantage over the stock plastic part is its temperature insensitivity. While the plastic case loses its strength with increasing temperatures and may finally disintegrate, the aluminum case stays intact.The one-piece design guarantees a true running and leak-free case. Steel bushing for drive cup shaft and O-ring.Fits front, center and rear applications on all Losi 5ive versions and Mini!Contents:1 piece
Genuine ATOP spare/option part. CNC-machined 6061-T6 aluminum intermediate transmission shaft bracket for Losi DBXL. The high strength of the material and the larger screws provide a secure seat for the bearings and add torsional rigidity.The set includes lager bearings (8 x 22 x 7) for higher load capacity and mounting bolts.Contents:1 piece This article is identical to the article in the video!
Genuine ATOP spare/option part. Front transmission mount for Losi DBXL cnc-machined from 6061 aluminum by ATOP.Through the use of aluminum, the problem of torn out threads (incl. the front bumper installation) is eliminated. At the same time the chassis section under the transmission is strengthened and the mounting points for the shock towers are reinforced.Comes with all mounting screws included.This is the new ATOP version with the additional mounting points between transmission housing and transmission bracket for a more secure connection of these parts.Old and new versions are fully compatible, regardless of whether they are made of aluminum or plastic. The parts therefore fit all versions of DBXL and MTXL in any combination.However, the use of the additional mounting points requires the new version of both transmission housing and bracket!Contents:1 piece This article is identical to the article in the video!
Genuine ATOP spare/option part.CNC-machined from 6061-T6 aluminum by ATOP. CNC-machined 6061-T6 aluminum servo clamps from Area RC distribute the load from the mounting screws equally over the complete area of the mounting tabs, protecting them against breakage. Available in two versions:AT-5T020-01 - 0236 for stock servos in Losi 5ive and DBXL, Savöx 235 und 236, Orange Power and other servos with a mounting hole distance of 18 mmAT-5T020-02 - 5765 for MPX Rhino, Hitec 5765 and other servos with a mounting hole distance of 16 mmContents:2 pieces
Delrin bushings, spare part for GPM rear lower a-arms BJ056 for HPI Baja cars, set of eight.Dimensions:Outer diameterer: approx. 8.1 mmInner diameter: approx. 6 mmLength: approx. 9.7 mm
Genuine ATOP spare/option part. Upper front camber rods with guide bushing set and with pivoted steel ball joints right/left thread and locknuts for Losi 5ive-T. Balls with 6 mm hole, adapter bushings for 5 mm screws, shortest distance between mounting points (center/center) 130 mm. Contents:2 pieces
y0557 Zenoah G230RC, with Walbro WT 603B carburetor (also available in the ball-raced version through the shop's options menu)23 cm³ Zenoah engine for large scale cars!The engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter and / or complete clutch are optionally available at additional charge.y1009 Zenoah G240RC with Walbro WT 990 carburetor (also available in the ball-raced version through the shop's options menu)23 cm³ Zenoah engine for large scale cars!Please note: contrary to their new designation the displacement has not been increased! The outer dimension didn't change, so you don't need any additional parts for the engine swap!The engines feature the following improvements over their G230RC:- Quantity of cylinder mounting bolts increased from 2 to 4- Improved strength of crankcase- Added additional bearing on the PTO (clutch) side of crankshaft- Redesigned shape of cylinder fins- Dimension of air intake port is 5% widerContains internal fuel pump which increases acceleration from idle to wide open throttle.Removal of choke valve increases performance by increasing air flow to the carburetor - Changed material of the insulator gasket to metal, which improves sealing performanceThe engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter and / or complete clutch are optionally available at additional charge. y0553 Zenoah G260RC with Walbro WT 603B carburetor (also available in the ball-raced version through the shop's options menu)This is the G260 in the 26 cm³ version.The engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter and / or complete clutch are optionally available at additional charge. y1011 Zenoah G270RC with Walbro WT 990 carburetor (also available in the ball-raced version through the shop's options menu)26 cm³ Zenoah engine for large scale cars!Please note: contrary to their new designation the displacement has not been increased! The outer dimension didn't change, so you don't need any additional parts for the engine swap!The engines feature the following improvements over their G260RC:- Quantity of cylinder mounting bolts increased from 2 to 4- Improved strength of crankcase- Added additional bearing on the PTO (clutch) side of crankshaft- Redesigned shape of cylinder fins- Dimension of air intake port is 5% wider- New carburetor (WT-990) Contains internal fuel pump which increases acceleration from idle to wide open throttle.Removal of choke valve increases performance by increasing air flow to the carburetor - Changed material of the insulator gasket to metal, which improves sealing performanceThe engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter are optionally available at additional charge. 7800 Zenoah G290RC with Walbro WT 990 carburetor (also available in the ball-raced version through the shop's options menu)Same dimensions as the Zenoah G230, G240, G260, G270.New generation Zenoah engine with 28,5ccm cylinder capacity and approx. 3.9 hp. The cylinder is fixed with 4 screws. The technical details are identical to the Zenoah engines G240RC and G270RC.The engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter and / or complete clutch are optionally available at additional charge. Compatibility Zenoah / Losi 5ive-T:Please note that for installation in a Losi 5ive the fan cover must be swapped for a Losi or CY cover #5341 in order to fit the chassis" bolt pattern.If you want to install a Zenoah engine into the Losi 5ive, you usually have to use a fan cover from the CY engine.However, there is a workaround to maintain Zenoah fan cover.The adjustment is done via the pinion specific mounting plates for the engine. The change always affects only the rear, outer (carburetor side) plate under the fan cover. This is rotated by 180°; so that the embossed number on this plate faces the exhaust side of the engine!18T pinion: use 20T plate, rotated 180°19T pinion: use 19T plate, rotated 180°20T pinion: use 18T plate, rotated 180°On the plus side you gain the opportunity to easily mount a Zenoah engine keeping the original fan cover. On the other hand there will be the disadvantage of the necessity to combine two different sets of engine mounting plates when installing any pinion other than the stock 19T version. Therefore we do not recommend this workaround for everyday use. Nevertheless it works perfectly should ever the need arise.Zenoah G320RC with Walbro WT 1107 carburetor (also available in the ball-raced version through the shop's options menu)With 32 cm³ and 30% more power than the Zenoah G290.Significantly more torque and higher stamina due to larger sized bearings all around, with Racing Carburetor Walbro WT 1107.The motor is supplied with WT-1107 carburetor and spark plug.SpecificationType: Two stroke gasoline engineDisplacement: 31,8 cm³Bore: 38 mmStroke: 28 mmWeight: 2,3 KgOverall Dimension:Length: 167 mmWidth: 215 mmHeight: 196 mmMaximum Output: 4,6 PSMaximum Torque: 2,00 N-mRotation Direction: CounterclockwiseCarburetor: Walbro WT-1107Spark plug: CMR7HStarting: Recoil starterFor all HPI Baja 5 cars the G320RCer clutch housing has to be shortened at the mounting base, for Losi 5ive- T and Desert Buggy XL cars the clutch housings overall length must be shortened to CY size.When installing the air filter you must pay attention to the length of the screws.For use on Losi and HPI we recommend M5x45 screws (like H94763); you can also cut existing screws to length, of course.When ordering with a modified clutch housing we will include these screws!In our shop you can select from Zenoah G320RC engines already modified to fit your HPI or Losi car.The installation of the Zenoah G320RC in other cars (like FG or Smartech buggies / monsters a.s.o.) is not even remotely straightforward, since the layshaft pinion (the small pinion in front of the big differential spur gear) is in the way for the larger Zenoah G320RC crankcase.Compatibility Zenoah / Losi 5ive-T:Please note that for installation in a Losi 5ive the fan cover must be swapped for a Losi or CY cover #5341 in order to fit the chassis" bolt pattern.If you want to install a Zenoah engine into the Losi 5ive, you usually have to use a fan cover from the CY engine.However, there is a workaround to maintain Zenoah fan cover.The adjustment is done via the pinion specific mounting plates for the engine. The change always affects only the rear, outer (carburetor side) plate under the fan cover. This is rotated by 180°; so that the embossed number on this plate faces the exhaust side of the engine!18T pinion: use 20T plate, rotated 180°19T pinion: use 19T plate, rotated 180°20T pinion: use 18T plate, rotated 180°On the plus side you gain the opportunity to easily mount a Zenoah engine keeping the original fan cover. On the other hand there will be the disadvantage of the necessity to combine two different sets of engine mounting plates when installing any pinion other than the stock 19T version. Therefore we do not recommend this workaround for everyday use. Nevertheless it works perfectly should ever the need arise.
Genuine Atop spare/option part.CNC-machined 6061-T6 aluminum front spindles from Area RC; fits Losi 5ive-T/B and Mini. Significantly more rigid than the stock plastic partthese spindles improve steering precision and tracking.They also feature larger outer bearings (12 x 28 x 7 mm) than stock for higher load capacity. All four ball bearings are sealing bearings.Contents:2 pieces
€79.90*
This website uses cookies to ensure the best experience possible. More information.... By clicking on "[Agree / Accept all / etc.]" you also give your consent to the disclosure of your behavior in our store to our partner, shopware AG (Ebbinghoff 10, 48624 Schöppingen, Germany), which cannot assign this data to you personally, but may process it for its own purposes (e.g. product improvements, market behavior analyses).