LOSB2071 Losi Front Suspension Arm Set 5T , 2 pcs.
€39.99
Sold out
Product information "LOSB2071 Losi Front Suspension Arm Set 5T , 2 pcs."
Since the beginning of 2014 Losi makes the a-arms about 4 mm longer. This does not cause any problems when installed in earlier version cars!
Content:
- 2 Pieces
Login
Customers also bought
Genuine Atop spare/option part.CNC-machined 6061-T6 aluminum front spindles from Area RC; fits Losi 5ive-T/B and Mini. Significantly more rigid than the stock plastic partthese spindles improve steering precision and tracking.They also feature larger outer bearings (12 x 28 x 7 mm) than stock for higher load capacity. All four ball bearings are sealing bearings.Contents:2 pieces
Genuine Motul spare/option part. High-cling oil for foam cartridge air filters, especially for offroad and street use. The oil reinforces the the air filter'e efficiency and retains dirt, mud and sand particles, which will greatly extend the life of the engine. The blue tint makes it easier to control even oil application to the filter.Apply oil to filter generously and work the foam vigorously by hand to ensure complete oil penetration. Press foam slightly to remove excessive oil when done.Contents:1 piece / 400 ml
Content: 400 Milliliter (€47.25 / 1000 Milliliter)
Genuine HT spare/option part. Protects the mated connection to prevent them from coming apart accidentally. Particularly recommended for direct power supply cords, as a tensile load on the cable can remove the link unnoticed and then you would perhaps think of a servo failure in the first place.The small size usually allows the installation even inside the receiver box.Also suitable for securing the connection of the receiver battery; the use of this clip means a big improvement in safety with little effort.Contents:1 piece
Item N° LOSB2575Headlight Set 5T, 2 pcs.
Genuine HT spare/option part. Helpful tool for removal of clutch shoes, flywheels and many more.FitsZenoah G230/G240/G260/G270/G290/G320Chung-Yang enginesPT enginesLosi enginesHPI enginesThreadsize:M10 x 1Contents:1 piece
Customers also viewed
Genuine Hitec spare/option part.Waterproof Power IP67 for large models and many industrial applicationsServo HS-1100WP is the most powerful and 100% waterproof servo Hitec large assortment! Thus, it is ideally suited for industrial applications and also for XXL large-scale models. Equipped with a hand-brush motor for maximum reliability and durability, and which protects from the full milled aluminum housing perfectly against electromagnetic interference. Another special course (not programmable) to call the virtually indestructible steel gears and a digital servo electronics IP67 classification.The Servo HITEC HS-1005SGT delivers maximum and constant performance and with its data also a favorite for industrial applications such as UAV, robotics and special effects. Technical data:Width: 33 mm Height: 73 mm Length: 64 mm Weight: 0340 kg Power Type: Mega Features: operating voltageFrom 11.1 to 14.8 volts, Amendment leads possible (Optional) Engine type servos: brushed Transmission: steel Operating voltage in V: 11.1 to 14.8 volts Actuating time s / 60 ° at 11.1 volts: 0:26 Setting time s / 60 ° at 14.8 volts: 12:19 Torque in kg cm at 6.0 volts: 84 Torque in kg cm at 7.4 volts: 110 Teeth: Mega Ball bearings: Yes, 2 times MR148 Waterproof: Yes Flight recommendation: YES Recommendation Heli: YES Recommendation Car: YES Recommendation boat: YES Temperature range: -20 ° to 60 ° CFeatures:Highest force Enormous holding power Indirect long-life potentiometer, 1 million cycles Steel gears Bearings, 2-MR148 Aluminum housing Separate signal and power supplyContents:1 piece
Genuine ATOP spare/option part.ATOP tie rod set with guide bushing set and with steel ball joints and turnbuckle center piece with locknuts for Losi 5ive-T.Balls with 6 mm bore diameter, adapter bushings for 5 mm screws, shortest distance between mounting points (center/center) 134 mm.Contents:2 pieces
Bushings set for GPM front a-arms part no. LO5T055.
Genuine ATOP spare/option part. Upper rear camber rods with guide bushing set and with pivoted steel ball joints right/left thread and locknuts for 5ive-T. Balls with 6 mm hole, adapter bushings for 5 mm screws, shortest distance between mounting points (center/center) 140 mm. Contents:2 pieces