The special tool for Lightscale wheel nuts is simply inserted into the end of a spark plug wrench and is secured there by use of an o-ring. With its 3 hardened pins the tool locates into the wheel nut and may be used to tighten or untighten it. The tool is universally usable for all Lightscale wheel nuts.The kit contains the tool as well as the o-ring and hardened pins. The tool comes ready for use. Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable.
Genuine Lightscale spare/option part.Square Hub with additional steel pins to secure wheels from damage due to turning on the hub.The Lightscale Diamond square hub is reduced to the maximum possible weight saving but serves even better lining and stiffness for the wheel and the brake disc. Furthermore the hub is slightly conical to its outside which makes mounting the tires easier especially in hectically racing situations.The Diamond is available in 11,5, 12 mm and 14,5mm width and fit all common known brands such as FG, RS-5, H.A.R.M. or Contrast and many more as well as all kinds of cars like on road, off road or Formula 1.Contents:2 pieces
Wheel nut front for F1 Cars using M6 Thread on the axle.The Lightscale wheelnut is used in combination with the Lightscale lexan disc to convert F1 rims to an up to date and modern look.Thereby the Lightscale wheel nut works just like a real one in present f1 racing. It is tightened with a 22 open end spanner or socket wrench. Alternatively one may use the special Lightscale tool to tighten or loosen the wheel nut.Due to the use of rifled and conical washers a locking effect is achieved.The kit contains 2 wheel nuts as well as 4 rifled conical washers.Optional parts: Tool for Lightscale wheel nuts item code 50100000, Lightscale lexan disc item code 51009500 and spare rifled conical washers item code 881200058801. Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable.
Wheel nut front for F1 Cars using M8 Thread on the axle.The Lightscale wheelnut is used in combination with the Lightscale lexan disc to convert F1 rims to an up to date and modern look.Thereby the Lightscale wheel nut works just like a real one in present f1 racing. It is tightened with a 22 open end spanner or socket wrench. Alternatively one may use the special Lightscale tool to tighten or loosen the wheel nut.Due to the use of rifled and conical washers a locking effect is achieved.The kit contains 2 wheel nuts as well as 4 rifled conical washers.Optional parts: Tool for Lightscale wheel nuts item code 50100000, Lightscale lexan disc item code 51009500 and spare rifled conical washers item code 881200058801. Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable.
Wheel nut rear for F1 Cars using M6 Thread on the axle.The Lightscale wheelnut is used in combination with the Lightscale lexan disc to convert F1 rims to an up to date and modern look.Thereby the Lightscale wheel nut works just like a real one in present f1 racing. It is tightened with a 22 open end spanner or socket wrench. Alternatively one may use the special Lightscale toolto tighten or loosen the wheel nut.Due to the use of rifled and conical washers a locking effect is achieved.Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable.The kit contains two wheel nutsas well as four rifled conical washersOptional parts: Tool for Lightscale wheel nuts (item code two wheel nutsas well as four rifled conical washersOptional parts: Tool for Lightscale wheel nuts (item code 50100000)
Wheel squares with 3 mm dowel pins. The pins prevent the squares from damaging the rims under high load. For all FG rims, holes may have to be drilled.11,5mm wide.Bore diameter 8 mm18 mm square
Genuine FG spare/option part.Square wheel driver in high-strength alloy material with M6 fixing thread. Essentially higher retention force. Suitable for all models.Dimensions:14 mm wide18mm squareBore diameter 8 mmContent:2 pieces
Suitable for all FG front uprights. The use of this front axle prevents a pressing and jamming of the inner ball bearing rings when tightening the wheel. Suitable for square wheel driver 9,5mm and 14mm.
Genuine Top Tuning spare/option part. Conversion kit for the standard 1:/5 18 mm square wheel drives for the Carson CY-Eline carsThis allows for the use of all 1/5 on-road wheels e.g. by or . The cars become approx. 5 mm wider per side. This i feasibles with all usual body shells of the CY-E-line cars. Set includes:4 pieces # y6107 hard coated 18 mm aluminum square drives, 9.5 mm wide, with 8 mm axle bore, threaded for 2 x M6 grub screws4 pieces M6 grub screws8 pieces 3x16 mm steel pins4 pieces # 6038 mounting washers 6x15 mm 4 pieces M5x16 mm countersunk screws
Genuine HT spare/option part.This adaptor allows you to install all MadMax/HPI tire/rim combinations on FG, Carso, Smartech 2WD/4WD and other cars with the same wheel shaft configuration. Losi 5ive tires can be used as well, but they hey have to be mounted on MadMax/HPI rims because Losi rims are too thick at the center. The adapter is drilled for 8 mm wheel shafts (FG, Smartech/Carson and many more!), hex size of wheel drive and wheel nut is 24 mm hex with M18x1.0 thread (same as HPI).Please note:FG wheel shafts come with either M6 or M8 thread size. It can even happen that a vehicle has different thread sizes front and rear! Therefore, please make sure which version is required before placing an order.Converting your car takes only a couple of minutes with this easy to install adaptor. just see picture "installation instruction" for a schematic installation.Contents:2 pieces
Item N° y1183/02FG rim to HPI model, drive rim adapter, separate for the front, 2 pcs.These adapters are machined from gas nitrited steel and enable you to put standard rims with 18 mm square drive (FG, Carson, Lauterbacher a.s.o.) on the HPI Baja 5B/SS/T. The track width will be substantially increased.For a complete set covering front and rear axle you need part number y1183.This set includes rim adapters with installation hardware for the front axle only.Measures for front:Outer diameter: circa 17,59 mLength: circa 55,10 mm
Genuine HT spare/option part. Hardened pins made of 100Cr6 steel for driveshafts, differentials, wheel drives and similar applications. Pack of ten. Sizes available:y1345/01: 4 x 18 mm, e.g. for Losi 5ive-T/Mini and HPI Baja differentials or HPI Baja layshafty1345/02: 4 x 20 mm, e.g. for Losi 5ive-T/Mini CVD jointsy1345/03: 4 x 24 mm, e.g. for Losi DBXL and HPI Baja wheel hexy1345/04: 5 x 24 mm, e.g. for Losi 5ive-T/Mini wheel hexContents:10 pieces
Two wheel squares with 3mm dowel pins. Like FG 6106/07, but made from heat treated steel. Significantly reduced wear. The pins prevent the squares from damaging the rims under high load. For all FG rims, holes may have to be drilled. Pins should be fitted using high strength thread locking compound.Measures:18 mm square11.5mm wideBore diameter 8 mm
Genuine HT spare/option part.Wheel squares made of high-strength aluminum, hardened, with two M6 mounting threads Suitable for most 1/6 and 1/5 rc-cars. Through the use of two 6 mm screws a significantly higher retention force is achieved. Yet it is still recommended to use medium strength thread lock (link y0114)! The hard anodizing (HART-COAT) guarantees much lower wear of the squares! Especially recommended when using wheel mounted brake discs! Four 3x16 dowel pins per square are included which prevent the squares from spinning in the rim. Press fitting them into the wheel squares is optional. The 12, 14 and 17 mm wide squares feature a groove for inserting a C-clip (link 6106/05), which acts as a guide for the brake disk. The narrow 9.5 mm wide squares dont need a clip; the close sitting rim will guide the disk. Measures18 mm square (wheel drive!)9,5 mm wide, 8.0 mm diameter axle boretwo M6 mounting threads The set includes 2 pieces of 9,5 mm wide wheel squares and 4 pieces each of M6 grub screws and 3x16 dowel pins.Contents:2 pieces
Genuine HT spare/option part.Wheel squares made of high-strength aluminum, hardened, with two M6 mounting threads Suitable for most 1/6 and 1/5 rc-cars. Through the use of two 6 mm screws a significantly higher retention force is achieved. Yet it is still recommended to use medium strength thread lock (link y0114)! The hard anodizing (HART-COAT) guarantees much lower wear of the squares! Especially recommended when using wheel mounted brake discs! Four 3x16 dowel pins per square are included which prevent the squares from spinning in the rim. Press fitting them into the wheel squares is optional. The 12, 14 and 17 mm wide squares feature a groove for inserting a C-clip (link 6106/05), which acts as a guide for the brake disk. The narrow 9.5 mm wide squares dont need a clip; the close sitting rim will guide the disk. Measures18 mm square (wheel drive!)14 mm wide, 8.0 mm diameter axle boretwo M6 mounting threads The set includes 2 pieces of 14 mm wide wheel squares and 4 pieces each of M6 grub screws and 3x16 dowel pins.Contents:2 pieces
Genuine HT spare/option part.Wheel squares made of high-strength aluminum, hardened, with two M6 mounting threads Suitable for most 1/6 and 1/5 rc-cars. Through the use of two 6 mm screws a significantly higher retention force is achieved. Yet it is still recommended to use medium strength thread lock (link y0114)! The hard anodizing (HART-COAT) guarantees much lower wear of the squares! Especially recommended when using wheel mounted brake discs! Four 3x16 dowel pins per square are included which prevent the squares from spinning in the rim. Press fitting them into the wheel squares is optional. The 12, 14 and 17 mm wide squares feature a groove for inserting a C-clip (link 6106/05), which acts as a guide for the brake disk. The narrow 9.5 mm wide squares dont need a clip; the close sitting rim will guide the disk. Measures18 mm square (wheel drive!)17 mm wide, 8.0 mm diameter axle boretwo M6 mounting threads The set includes 2 pieces of 17 mm wide wheel squares and 4 pieces each of M6 grub screws and 3x16 dowel pins.Contents:2 pieces
Genuine HT spare/option part.Wheel squares made of high-strength aluminum, hardened, with two M6 mounting threads Suitable for most 1/6 and 1/5 rc-cars. Through the use of two 6 mm screws a significantly higher retention force is achieved. Yet it is still recommended to use medium strength thread lock (link y0114)! The hard anodizing (HART-COAT) guarantees much lower wear of the squares! Especially recommended when using wheel mounted brake discs! Four 3x16 dowel pins per square are included which prevent the squares from spinning in the rim. Press fitting them into the wheel squares is optional. The 12, 14 and 17 mm wide squares feature a groove for inserting a C-clip (link 6106/05), which acts as a guide for the brake disk. The narrow 9.5 mm wide squares dont need a clip; the close sitting rim will guide the disk. Measures18 mm square (wheel drive!)12 mm wide, 8.0 mm diameter axle boretwo M6 mounting threads The set includes 2 pieces of 12 mm wide wheel squares and 4 pieces each of M6 grub screws and 3x16 dowel pins.Content:2 pieces
€16.45*
This website uses cookies to ensure the best experience possible. More information...