Genuine HT spare/option part. The best solution for drive shaft positioning, can be used with ball drives or regular "dog bones" as well.The springs will be simply inserted into the drive cups.DImensions:Diameter: 11 mmHeight: 8 mmContents:4 piece

Genuine HT spare/option part. Protect ball drive as well as cardan drive against dirt. For FG and Carson ball drives, fits standard dogbones as well.Contents:2 pieces

Genuine HT spare/option part.Wheel squares made of high-strength aluminum, hardened, with two M6 mounting threads Suitable for most 1/6 and 1/5 rc-cars. Through the use of two 6 mm screws a significantly higher retention force is achieved. Yet it is still recommended to use medium strength thread lock (link y0114)! The hard anodizing (HART-COAT) guarantees much lower wear of the squares! Especially recommended when using wheel mounted brake discs! Four 3x16 dowel pins per square are included which prevent the squares from spinning in the rim. Press fitting them into the wheel squares is optional. The 12, 14 and 17 mm wide squares feature a groove for inserting a C-clip (link 6106/05), which acts as a guide for the brake disk. The narrow 9.5 mm wide squares dont need a clip; the close sitting rim will guide the disk. Measures18 mm square (wheel drive!)9,5 mm wide, 8.0 mm diameter axle boretwo M6 mounting threads The set includes 2 pieces of 9,5 mm wide wheel squares and 4 pieces each of M6 grub screws and 3x16 dowel pins.Contents:2 pieces

Genuine HT spare/option part.Wheel squares made of high-strength aluminum, hardened, with two M6 mounting threads Suitable for most 1/6 and 1/5 rc-cars. Through the use of two 6 mm screws a significantly higher retention force is achieved. Yet it is still recommended to use medium strength thread lock (link y0114)! The hard anodizing (HART-COAT) guarantees much lower wear of the squares! Especially recommended when using wheel mounted brake discs! Four 3x16 dowel pins per square are included which prevent the squares from spinning in the rim. Press fitting them into the wheel squares is optional. The 12, 14 and 17 mm wide squares feature a groove for inserting a C-clip (link 6106/05), which acts as a guide for the brake disk. The narrow 9.5 mm wide squares dont need a clip; the close sitting rim will guide the disk. Measures18 mm square (wheel drive!)14 mm wide, 8.0 mm diameter axle boretwo M6 mounting threads The set includes 2 pieces of 14 mm wide wheel squares and 4 pieces each of M6 grub screws and 3x16 dowel pins.Contents:2 pieces

Genuine HT spare/option part.Wheel squares made of high-strength aluminum, hardened, with two M6 mounting threads Suitable for most 1/6 and 1/5 rc-cars. Through the use of two 6 mm screws a significantly higher retention force is achieved. Yet it is still recommended to use medium strength thread lock (link y0114)! The hard anodizing (HART-COAT) guarantees much lower wear of the squares! Especially recommended when using wheel mounted brake discs! Four 3x16 dowel pins per square are included which prevent the squares from spinning in the rim. Press fitting them into the wheel squares is optional. The 12, 14 and 17 mm wide squares feature a groove for inserting a C-clip (link 6106/05), which acts as a guide for the brake disk. The narrow 9.5 mm wide squares dont need a clip; the close sitting rim will guide the disk. Measures18 mm square (wheel drive!)17 mm wide, 8.0 mm diameter axle boretwo M6 mounting threads The set includes 2 pieces of 17 mm wide wheel squares and 4 pieces each of M6 grub screws and 3x16 dowel pins.Contents:2 pieces

Genuine HT spare/option part.Wheel squares made of high-strength aluminum, hardened, with two M6 mounting threads Suitable for most 1/6 and 1/5 rc-cars. Through the use of two 6 mm screws a significantly higher retention force is achieved. Yet it is still recommended to use medium strength thread lock (link y0114)! The hard anodizing (HART-COAT) guarantees much lower wear of the squares! Especially recommended when using wheel mounted brake discs! Four 3x16 dowel pins per square are included which prevent the squares from spinning in the rim. Press fitting them into the wheel squares is optional. The 12, 14 and 17 mm wide squares feature a groove for inserting a C-clip (link 6106/05), which acts as a guide for the brake disk. The narrow 9.5 mm wide squares dont need a clip; the close sitting rim will guide the disk. Measures18 mm square (wheel drive!)12 mm wide, 8.0 mm diameter axle boretwo M6 mounting threads The set includes 2 pieces of 12 mm wide wheel squares and 4 pieces each of M6 grub screws and 3x16 dowel pins.Content:2 pieces

Wheelie bar with double ball raced wheel, cnc-machined from high strength alloy. The arm has a rubber suspension unit, the height is infinitely adjustable. The suspension allows for a maximum deflection of 30 degrees and is dirt- and mud-proof. The wheel bearings are sealed.The unit fits FG Monster Truck, Monster Beetle and Marder BigFoot, except for Monster Buggy Off-Road WB535 4WD. Installation on other models will be possible, but requires modifications to the chassis, mainly to accept the bolt pattern. The Carson Attack already has the correct pattern.

Genuine FG spare/option part. The set will shipped without gear carrier plate. Contents:1 set

Genuine HT spare/option part.Alloy upright for a ball fastening at the upper wishbone. Adjustable at the lower wishbone (hinge pin), too. Fits the rear axle of all FG and Carson / Smartech 1/6 scale cars.Comes with adjustment clips and grub screws for the hinge pins included.Dimensions:Bearing seats: 22 x 7 mmHinge pin bore: 6 mmDistance wheel shaft/hinge pin: 25 mm Contents:2 pieces

Genuine FG spare/option part. Please note: If you own a Leopard 2WD with the old 130.5 mm driveshafts (same part number), the upgrade of both shafts is recommended.Contents:1 piece

Genuine HT spare/option part. Dimensions:Total length: approx. 132 mmLength center pin / center pin: approx. 123 mmShaft diameter: approx. 6 mmBall diameter: approx. 9,8 mmPlease note:If you own a Leopard 2WD with the old 130.5 mm driveshafts, the swap of both shafts is recommended.Contents:1 piece

Alloy upright for a ball fastening at the upper wishbone. Adjustable at the lower wishbone (wishbone pin), too. Fits the rear axle of all FG offroad cars (2WD and 4WD) and all Carson / Smartech cars.Content:Bearing seats: 22 x 7 mmHinge pin bore: 6 mmDistance wheel shaft/hinge pin: 25 mm

For the secure installation of driveshaft boots.

Genuine FG spare/option part.Alloy rear axle mount right Leopard 2WD/4WD.

Genuine FG spare/option part.Replacement part for: 67360 Conversion kit for gear brake Leopard

The set includes belt pulley housing right and left, screws. Suitable for Off-Road Buggy 4WD RTR, Off-Road Beetle 4WD RTR and Monster/ Stadium models 4WD RTR, 4WD Porsche.

Item N° 9473Ball drive set for Leopard Sportsline, setFits for 2WD/4WD Sportsline.Not suitable for front application on 4WD cars!

Tuning aluminum rear suspension set for nearly all FG 4WD Sportsline cars: Monster-Truck, Off-Road Buggy, Marder, Beetle, Tourenwagen.Does not fit Formula 1, Leopard and Truggy!Assembled units in the pictures are completed with some parts which are not included. These parts will be re-used from the stock suspension when swapping in the aluminum version. You will also need two bags of 6100/04 Turnbuckle left/right M8/40mm.y2004/01 fits:FG 4WD Monster-Truck models and Monster Beetle models, Off-Road, Marder, Beetle, Porsche GT3 RSR and Race Trucks. The only difference between the sets is the length of the lower a-arms (y2004/01 = long, y2004/02 = short). The picture of the assembled set is used for both versions and shows the shorter arms.Part number:Name:y2001Aluminum rear upper a-armsy68401Aluminum rear lower a-arms long66213Aluminum rear shock towery66205/06Aluminum rear diff mountsy2004/02 fits:FG 4WD Touring car models (except Porsche GT3 RSR).Part number:Name:y2001Aluminum rear upper a-armsy68401/01Aluminum rear lower a-arms short66213Aluminum rear shock towery66205/06Aluminum rear diff mountsy2004/03 fits:FG 4WD/2WD Off-Road WB535.Part number:Name:y2001Aluminum rear upper a-armsy68401Aluminum rear lower a-arms long66213/02Aluminum rear shock towery66205/06Aluminium rear diff mounts

Genuine FG spare/option part.Spare part for the Leopard 2010 version.

Genuine FG spare/option part.

The set includes right and left rear axle mounts, damper plate and screws.Suitable for Off-Road Buggy 2WD/4WD RTR, Off-Road Beetle 4WD RTR and Monster/ Stadium models 4WD RTR, for all 2WD/4WD On-Road models. For older 2WD models that are not based on the 4WD models, please refer to Sportsline 2008. or if an RC plate is no longer fitted, check Sportsline 13 in Parts Scout.There you will find the right spare parts for your vehicle.https://rc-car-online.de/en-ersatzteile_main,15.html

Spare Part for all FG 2WD/4WD Models.Attention!For Upgrading a FG 4WD Sportsline Model we recommend the Tuningkit y68400. This Kit includes all necessary small parts and screws. For older 2WD models that are not based on the 4WD models, please refer to Sportsline 2008. or if an RC plate is no longer fitted, check Sportsline 13 in Parts Scout.There you will find the right spare parts for your vehicle.https://rc-car-online.de/en-ersatzteile_main,15.html

Genuine FG spare/option part. Precise, solid and reliable, for use at competitions, not adjustable.Suitable for Off-Road Buggy 4WD RTR, Off-Road Beetle 4WD RTR and Monster/Stadium models 4WD RTR.Content:1 set

Genuine HT spare/option part. Hardened pins made of 100Cr6 steel for driveshafts, differentials, wheel drives and similar applications. Pack of ten. Sizes available:y1345/01: 4 x 18 mm, e.g. for Losi 5ive-T/Mini and HPI Baja differentials or HPI Baja layshafty1345/02: 4 x 20 mm, e.g. for Losi 5ive-T/Mini CVD jointsy1345/03: 4 x 24 mm, e.g. for Losi DBXL and HPI Baja wheel hexy1345/04: 5 x 24 mm, e.g. for Losi 5ive-T/Mini wheel hexContents:10 pieces