66221 FG Alloy tensioning pulley case, r/h 4WD
€38.95
Currently unavailable
Product information "66221 FG Alloy tensioning pulley case, r/h 4WD"
Contents:
- 1 piece
Lebacher Strasse 4
66113 Saarbrücken
Germany
Login
Customers also bought
Genuine FG spare/option part. Contents:1 piece
Ball bearings sealed for Gilmer belt pulley 4WD for FG models. Fits for FG no. 66255Bulk: 6 x 15 x 5 mm
Genuine HT spare/option part. Five antenna tubes with caps.Size: Length: 300 mmContent:1 set
Genuine HT spare/option part.Alloy upright for a ball fastening at the upper wishbone. Adjustable at the lower wishbone (hinge pin), too. Fits the rear axle of all FG and Carson / Smartech 1/6 scale cars.Comes with adjustment clips and grub screws for the hinge pins included.Dimensions:Bearing seats: 22 x 7 mmHinge pin bore: 6 mmDistance wheel shaft/hinge pin: 25 mm Contents:2 pieces
Item N° 67240Alloy servo retainer, 2-parts, fixed, 2pcs.
Genuine Dynamite spare/option part.Key Features:Kills your 2-cycle gas engine on command, loss of radio signal, low battery, or total battery power lossComes ready to install no soldering requiredOptically Coupled to isolate your ignition system from your radio systemBuilt-in LED for easy-to-spot operational status3-Channel Radio System RequiredNot Compatible with AVC-Equipped ReceiversContents:1 piece
Customers also viewed
Large alloy engine mount for all FG 4WD cars.Contrary to the FG pack this one includes the complete hardware for installation in Sportsline cars as well!
Tuning aluminum engine mount set for all FG 4WD Sportsline cars: Monster-Truck, Off-Road Buggy, Marder, Beetle, Touring Cars.Inhalt:Aluminum large engine / layshaft mountAluminum small engine mountAll necessary screws are included!
Item N° 67239 Aluminium servo saver bridge Leopard 4WD, 1pce.Spare part for the Leopard 2010 4WD version
Genuine FG spare/option part. CNC-cut alloy engine mount for all FG 1:5 and 1:6 Truck models with horizontal engine ahead as Zenoah ZG22, G230RC, G260RC, FG CY23 and CY26.Bearing seat 19 x 7 mm.Contents:1 piece
Genuine Speed-Tec spare/option part. Due to the air boxes mandatory for racing and the required off-road air filters, a strong and rigid insulator is a must! No more stripped threads, no warpage and the resulting air leaks at the insulator anymore! So many weird running behaviors, for example if the engine is warmed up and a tiny gap occurred at the insulator, are caused by this distortion of a plastic insulator. The increased heat transfer of the aluminum is taken into account by addition of an insulator plate. Therefore the aluminum intake is largely insulated. Due to the face-milled surfaces of the aluminum intake you reach a greater durability of the gaskets. The SPEED TEC aluminum insulator is available with two insulator plates.y1354/01 SPEED TEC cross aluminum insulator with 7 mm insulator plate and therefore a longer intake path for more torque. Ideal for off-road and cars. y1354/02 SPEED TEC Race aluminum insulator with 4 mm insulator plate, better for maximum rpm and therefore best for on-road use! Dimensions: Height of aluminum intake 20 mmHeight of cross version insulator plate - 7mm Height of Race version insulator plate - 3 mm Contents:Aluminum intake insulator plate 3 x gasket 2 x allen screw 5 x 30 mm 2 x washer 5/9.8 mm
Genuine HT spare/option part.Spare part for y0932.Contents:1 piece