y0897 Wheelie bar with suspension for 2WD + 4WD models - 1pce.

€89.90*

Available

Product number: ha_0001

EAN: 4058575010937

Product information "y0897 Wheelie bar with suspension for 2WD + 4WD models - 1pce."

Wheelie bar with double ball raced wheel, cnc-machined from high strength alloy. The arm has a rubber suspension unit, the height is infinitely adjustable. The suspension allows for a maximum deflection of 30 degrees and is dirt- and mud-proof. The wheel bearings are sealed.

The unit fits FG Monster Truck, Monster Beetle and Marder BigFoot, except for Monster Buggy Off-Road WB535 4WD. Installation on other models will be possible, but requires modifications to the chassis, mainly to accept the bolt pattern. The Carson Attack already has the correct pattern.

0 of 0 reviews

Leave a review!

Share your experiences with other customers.

Login

Your email address

Your password

Display reviews in current language only.

No reviews found. Share your insights with others.

Customers also bought

AR-023 Fuel line hose clamps

For a secure fit of the fuel line. The self-adjusting clamps are suitable for diameters from 6 to 7 mm.Contents:10 pieces

€8.90*

y1380 High performance starter rope, carbon grey

3 mm high performance starter rope; with a breaking strength of almost a metric ton it is far superior to any other starter rope available. Even large displacement high compression engines are no match for this rope. Please note:The usual fusion of cutting edges and knots on standard starter ropes using a flame is mostly unrewarding with this rope! We therefore recommend securing the knots with 2 - 3 drops of superglue on the outside. Length approx. 80 cm; fits all current pull starters.

€8.90*

y6107/01 Wheel squares 18 mm HART-COAT, 14 mm wide

Genuine HT spare/option part.Wheel squares made of high-strength aluminum, hardened, with two M6 mounting threads Suitable for most 1/6 and 1/5 rc-cars. Through the use of two 6 mm screws a significantly higher retention force is achieved. Yet it is still recommended to use medium strength thread lock (link y0114)! The hard anodizing (HART-COAT) guarantees much lower wear of the squares! Especially recommended when using wheel mounted brake discs! Four 3x16 dowel pins per square are included which prevent the squares from spinning in the rim. Press fitting them into the wheel squares is optional. The 12, 14 and 17 mm wide squares feature a groove for inserting a C-clip (link 6106/05), which acts as a guide for the brake disk. The narrow 9.5 mm wide squares dont need a clip; the close sitting rim will guide the disk. Measures18 mm square (wheel drive!)14 mm wide, 8.0 mm diameter axle boretwo M6 mounting threads The set includes 2 pieces of 14 mm wide wheel squares and 4 pieces each of M6 grub screws and 3x16 dowel pins.Contents:2 pieces

€17.45*

y7087/02 Alloy shock shaft end long

Genuine HT spare/option part.Replaces FG 7087/02.Fits all FG shocks, Carson 2WD and many other 1/5 and 1/6 scale models. There are replaceable bushings.Dimensions:Length overall: 27 mm, about 22 mm to to center of bushingThread for shock shaft: M4Bushing inner diameter: 4 mmContents:2 pieces

€15.90*

y0563 Alloy front shock tower for 4WD FG-Monster/Stadiuim/Beetle Leopard cars

Genuine HT spare/option part. Milled to reduce weight; replaces plastic part FG #66287/01. Comes complete with all necessary mounting hardware included.Fits Leopard Sportsline 2WD and 4WD.Scope of delivery:1x Alloy front shock tower4x Socket head cap screws 4x143x Countersunk screws 4x144x Washers steel 4,3Contents:1 piece

€79.90*

y1072 HT Alloy differential spur gear protector

Genuine HT spare/option part.Gear protector for the bottom of the 2WD chassis plate. Replaces stock plastic part FG 6082 or Carson 32481.Contents:1 piece

€29.90*

Similar products

y1218 Springs for drive shafts

Genuine HT spare/option part. The best solution for drive shaft positioning, can be used with ball drives or regular "dog bones" as well.The springs will be simply inserted into the drive cups.DImensions:Diameter: 11 mmHeight: 8 mmContents:4 piece

€4.90*

y1004 Driveshaft boots for ball drive + dogbones

Genuine HT spare/option part. Protect ball drive as well as cardan drive against dirt. For FG and Carson ball drives, fits standard dogbones as well.Contents:2 pieces

€8.90*

y6107/02 Wheel squares 18 mm HART-COAT, 17 mm wide

Genuine HT spare/option part.Wheel squares made of high-strength aluminum, hardened, with two M6 mounting threads Suitable for most 1/6 and 1/5 rc-cars. Through the use of two 6 mm screws a significantly higher retention force is achieved. Yet it is still recommended to use medium strength thread lock (link y0114)! The hard anodizing (HART-COAT) guarantees much lower wear of the squares! Especially recommended when using wheel mounted brake discs! Four 3x16 dowel pins per square are included which prevent the squares from spinning in the rim. Press fitting them into the wheel squares is optional. The 12, 14 and 17 mm wide squares feature a groove for inserting a C-clip (link 6106/05), which acts as a guide for the brake disk. The narrow 9.5 mm wide squares dont need a clip; the close sitting rim will guide the disk. Measures18 mm square (wheel drive!)17 mm wide, 8.0 mm diameter axle boretwo M6 mounting threads The set includes 2 pieces of 17 mm wide wheel squares and 4 pieces each of M6 grub screws and 3x16 dowel pins.Contents:2 pieces

€18.95*

y6107/01 Wheel squares 18 mm HART-COAT, 14 mm wide

€17.45*

y04475 HT Rear alloy shock mount 2WD

Genuine HT spare/option part.Rear alloy damper plate with several adjustment possibilities of the shock absorbers. Replacement for FG plastic rear shock tower FG 7072/01Please note: When installing in combination with plastic diff mounts you should insert a-arms with hinge pins before bolting together rear plate and diff mounts.Content:1 pieces

€89.90*

y1072 HT Alloy differential spur gear protector

Genuine HT spare/option part.Gear protector for the bottom of the 2WD chassis plate. Replaces stock plastic part FG 6082 or Carson 32481.Contents:1 piece

€29.90*

7497/01 FG Rear brake 2WD/4WD

Genuine FG spare/option part. The set will shipped without gear carrier plate. Contents:1 set

€55.90*

y6479 HT rear alloy upright

Genuine HT spare/option part.Alloy upright for a ball fastening at the upper wishbone. Adjustable at the lower wishbone (hinge pin), too. Fits the rear axle of all FG and Carson / Smartech 1/6 scale cars.Comes with adjustment clips and grub screws for the hinge pins included.Dimensions:Bearing seats: 22 x 7 mmHinge pin bore: 6 mmDistance wheel shaft/hinge pin: 25 mm Contents:2 pieces

€89.90*

y0264 C-clips with handle 4 - 6 mm

clipse_griff Size: y0264/06 - 6 mm

Genuine HT spare/option part.Quick change clips for installation and de-installation without tools, galvanic zinc plated.Spring steel, hardened and tempered to 1450 to 1600 N/mm² tensile strength.Available for 4, 5 and 6 mm shafts.Contents:10 pieces

€4.90*

6479 FG Rear alloy uprights 08

Alloy upright for a ball fastening at the upper wishbone. Adjustable at the lower wishbone (wishbone pin), too. Fits the rear axle of all FG offroad cars (2WD and 4WD) and all Carson / Smartech cars.Content:Bearing seats: 22 x 7 mmHinge pin bore: 6 mmDistance wheel shaft/hinge pin: 25 mm

€133.95*

y6106/07 Wheel square 11,5mm, steel

Two wheel squares with 3mm dowel pins. Like FG 6106/07, but made from heat treated steel. Significantly reduced wear. The pins prevent the squares from damaging the rims under high load. For all FG rims, holes may have to be drilled. Pins should be fitted using high strength thread locking compound.Measures:18 mm square11.5mm wideBore diameter 8 mm

€19.90*

y6107/07 Wheel squares 18 mm HART-COAT, 12 mm wide

Genuine HT spare/option part.Wheel squares made of high-strength aluminum, hardened, with two M6 mounting threads Suitable for most 1/6 and 1/5 rc-cars. Through the use of two 6 mm screws a significantly higher retention force is achieved. Yet it is still recommended to use medium strength thread lock (link y0114)! The hard anodizing (HART-COAT) guarantees much lower wear of the squares! Especially recommended when using wheel mounted brake discs! Four 3x16 dowel pins per square are included which prevent the squares from spinning in the rim. Press fitting them into the wheel squares is optional. The 12, 14 and 17 mm wide squares feature a groove for inserting a C-clip (link 6106/05), which acts as a guide for the brake disk. The narrow 9.5 mm wide squares dont need a clip; the close sitting rim will guide the disk. Measures18 mm square (wheel drive!)12 mm wide, 8.0 mm diameter axle boretwo M6 mounting threads The set includes 2 pieces of 12 mm wide wheel squares and 4 pieces each of M6 grub screws and 3x16 dowel pins.Content:2 pieces

€16.45*

Details

Customers also viewed

- GWH04-XM2 GRP W04 REVO XM2 Tyres Medium

This pair of Tyres have the following use indications: HIGH GRIP situation for clean track. HIGH GRIP situation for big asphalt. HIGH GRIP situation for high temperatures. This pair of Tyres have the following technical features: REVO treated profile for the maximum traction and the maximum lateral grip. Treated profile studied to maintain the tyre surface alway clean from rubber murble. Compound exclusively developped for model tyres. Inside belt flexible but very strong, vulcanized directly together with tyre compound. Insert foam with special material for high temperatures, for maximum stability and high drive precision. Spoked wheel moulded with special material for high temperatures for maximum grip and stability. Special gluing system 100% guaranteed.The main sizes for this tyre are: WHEEL fixing with square 18mm. TYRE outside diameter 118mm. WHEEL inside diameter 90mm. TYRE tota width 65mm. Note:The harder a tire compound - the longer it lasts, but the more moderate the performance.The softer a tire compound - the better the performance, but the lower the durability. Hint!As a rule, the same tires can be used for front and rear.If the vehicle tends to oversteer, this can be avoided by using a harder front tire!In wet conditions you should use a rain tire which offers maximum grip under these circumstances.With the use of Magic Rain, a tire traction compound, the grip can be further improved.Check your tires after driving! It can happen that a tire starts to detach from the rim, in this case you should glue this spot immediately with our tire repair kit (y0067), otherwise the tire could detach completely from the rim.So find out which tire is the best for you!

€38.90*

y0578, Alloy front shock tower for FG Sportsline and Off-Road 4WD, 1 pce.

Aluminum front shock tower for FG Off-Road Buggy and Sportsline 4WD, replaces stock plastic part FG #66287.Stock mounting hardware will be re-used.

€59.90*

21100/01 FG Body Stadium/Street-Truck white for 2WD - 1 pce.

The bodyshell is made from colored polycarbonate.The decal set, the front section and the rear wing are not included!Length: 660 mmWidth: 290 mmHeight: 195 mmWheelbase: 460 mm

€133.95*

26100/01 FG Body Monster / Stadium-truck 2WD/4WD white

Genuine FG spare/option part.Spare part for FG Monster Truck and Monster / Stadium Truck 2WD/4WDScope of delivery consists of the painted body shell (front and main section). The shop menu allows you to select different decal sets, roll bar and off-road light dummies.Dimensions:Length: 660 mmWidth: 290 mmHeight: 195 mmWheelbase: 460 mmWith some modifications also suitable for Smartech / Carson Monster Truck, Pick Up Truck, Comanche, Stadium Truck as well as Monster Beetle. New mounting holes must be drilled and the bottom area of the bed must be almost completely removed to keep the roll cage of the Carson Smartech car. Contents:1 set

€136.00*

7497/01 FG Rear brake 2WD/4WD

Genuine FG spare/option part. The set will shipped without gear carrier plate. Contents:1 set

€55.90*

6000CZ30 FG Marder 2WD Legend 30 Years - limited and numbered special edition

To celebrate the 30th anniversary of the legendary Marder 1/6 scale 2WD buggy, FG Modellsport/T2M releases a special edition, limited to 300 numbered pieces, with the original signature of Franz Gröschl on the sticker sheet as well as a top equipment (G260RC Zenoah engine, hi-capacity low friction aluminum shock absorbers and special aluminum engine mounts). with original 260 Zenoah with Low-Friction Alu shocks with alloy enginemount The Models is built on a 4 mm u-bended chassis. All borings of the lower side are countersunk, therefore the screw heads can't bear out.Double wishbones at font and rear axle as well as 4 bulk oil-pressure shock absorbers guarantee perfect ground adherence. All rotating parts are supported by ball-bearings. Rear gear wheels, differential gears and all driving elements are case-hardened. The side guards protect the model from dirt. With original signature of Franz Gröschl. The model is equipped with a powerfull 26 ccm engine which runs with normal 2-stroke petrol-oil mixture (available at every petrol station). The tank filling of 0,7 liters enables you to drive about 45 minutes. The engine can be started without difficulties through the integrated pull-start. To complete the models all merchantable servos and radio control systems are suitable.You can select the car with complete RTR-equipment from the options menu. RTR-equipment RTR = Ready to Run. The RTR version comes ready to use with the 2,4 GHz rc-system already installed. Transmitter: Reflex Wheel Pro III 2,4 GHzReceiver: Mini BECHigh power servo for throttle and brakeLargescale servo for steeringTx-battery, rx-battery

€799.99*

Configure now

Perforated clutch bell Lauterbacher, used ‘1’

Used perforated Lauterbacher clutch bell. Fits many 1:5 FG and Carson 2WD models. See photos for condition and scope of delivery. 1 piece

€15.00*