Genuine FG spare/option part. Contents:1 pieceFor older 2WD models that are not based on the 4WD models, please refer to Sportsline 2008. or if an RC plate is no longer fitted, check Sportsline 13 in Parts Scout.There you will find the right spare parts for your vehicle.
Genuine FG spare/option part.Contents:1 pieceFor older 2WD models that are not based on the 4WD models, please refer to Sportsline 2008. or if an RC plate is no longer fitted, check Sportsline 13 in Parts Scout.There you will find the right spare parts for your vehicle.
Genuine Top Tuning spare/option part. All aluminum parts are made of 7075 alloy.Front motor mount design to assure ample clearance for the rear brake disc when running mechanical brakes.Accepts two batteries up to 150 mm long und 50 mm wide. The battery tray accepts batteries up to 164 mm long, but the motor pinion limits the max. length of one battery to 155 mm.Rear motor clamps:
- Diameter 55,75 mm z.b. for Losi Spektrum 780 kV - Diameter 57 mm z.B. for Tenshock oder Castle- Diameter 57,8 mm z.B. for Leopard Baureihe 58- Diameter 60 mm z.B. for Lehner- Diameter 70 mm z.B. for BP70120 ZTW Beast Brushless Motor 620 kV
Please note: This set does not include Motor or ESCThis conversion kit is not intended for the 5ive-T 2.0, even though the installation in this vehicle would be feasible with some modifications (drilling and thread tapping required). The version for the 5ive-T 2.0 you can find here: TT1024. Driving batteries with the following maximum dimensions can be installed: Length: 165 mm Width: 51 mm Height: variable The speed controller (ESC) requires EC8 connections or corresponding ! Contents:Motor mount with your choice of rear clamp for 57 / 57.8 / 60 / 70 mm motor diameterBattery carrier plate made of 3 mm epoxy with aluminum brackets for the hook-and-loop tapes4 hook-and-loop tapes to secure the batteriesaluminum mounting pedestals for the battery plate16T pinion with 8 mm bore diameterMounting screws
Genuine HT spare/option part.Very strong linkage with M6 steel ball joints.M6 threaded rod with lock nuts, balls with holes for M4 screws.Maximum length about 96 mm, but through cutting the M6 rod allows for a minimum length of 48 mm.Significantly stronger than the standard plastic version, and especially recommend when using the Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP servo, this linkage can be used with "normal" servos as well.The threaded rod is not designed as a turnbuckle for a reason because there is not need to change the adjusted length for this application after installation. The setting accuracy of 0.5 mm (½ turn) means a maximum difference to the ideal length of 0.25 mm. This is always sufficient, the trim on the transmitter handles the final adjustment.On the other hand, a connecting rod with the same thread on both ends will always keep its setting when installed, even when both lock nuts are not tightened against the ball joints. Therefore reliability is higher.Set includes:2 x steel ball joints M62 x flat lock nuts1 x M6 x 60 mm threaded piece for Losi 5ive-T1 x M6 x 80 mm threaded piece for Losi 5ive-T 2.02 x spacer tubesContents:1 piece
Genuine Top Tuning spare/option part. Motor pinion made of nitrided hardened steel, module 1.5 and 8 mm bore. Reinforced hub for set screw M5x6. The pinions with odd tooth counts are profile shifted. Within the same outer diameter, there is no need to adjust the backlash when changing the pinion. When mounting on vehicles with mounting holes in the motor mount that are specific to the tooth count, the mounting holes for the higher number of teeth in each case (16 or 18) must be used.Profile regraded:This means that the number of teeth is changed while the diameter remained constant. The part of the involute curve that defines the tooth profile is changed. Positively regraded (lower number of teeth) pinions are stronger and run smoother, the reduced strength of negatively regraded pinions doesn´t really matter. Available in two sizes with two tooth counts:Outer diameter 30 mm with 17T or 18TOuter diameter 27 mm with 15T or 16TContents:1 piece
Genuine Top Tuning spare/option part. Spare part for electric conversion kit TT1021 or for your own designs.Fits BP70120 ZTW Beast Brushless motor 620 kV.Bolt pattern: 4 x for M4 screws on 30 mm pitch circleDistance center of motor / base plate: 37 mmContents:1 piece
Genuine Top Tuning spare/option part. Spare part for electric conversion kit TT1021 or for your own designs.Available with the following diameters:Diameter 57 mm i.e. for Tenshock or CastleDiameter 57,8 mm i.e. for Leopard Baureihe 58Diameter 60 mm i.e. for LehnerDiameter 70 mm i.e. for BP70120 ZTW Beast Brushless engine 620 kV, requires the taller TT1021/01B Top Tuning Motor mount for ZTW Beast motorDiameter 55,75 mmContents:1 piece
For converting the Sportsline long touring car into a model with 4WD drive. The conversion kit contains all chassis parts and drive parts that are required for the conversion.
Genuine Losi spare/option part. The esc mounting bracket is equipped with an extremely strong double-sided adhesive tape for fixing the controller. Additionally the esc can be secured with the Top Tuning Velcro TT1021/12, which you can select from the shopping options.Compared to the standard plate, the support surface has been widened by 1mm, so that the ZTW 300A controller can be mounted ideally; slipping back and forth is securely avoided.Contents:1 set
Item N° 68510 Electric conversion kit 1:6 2WD for 465 Wheelbase, setSuitable for 2WD Buggy and Monster models as Marder, Beetle, Monster-Truck, Hummer, Jeep a.s.o with 465 mm wheelbase.This conversion kit is suitable for the 2WD FG models Marder, Beetle, Off-Road Buggy and Monster models with 465mm wheelbase. Suitable for the electric engines from FG Modellsport, Leopard BL engines and Castle Creation. The conversion kit includes gear and engine mount, fixing parts for cruise control and LiPo batteries. Cruise control, BL engine and LiPo batteries are not included. During the conversion several fixing holes have to be applied to the chassis. Gear transmission has to be changed accordingly to the use of the electric engine.For easy mounting we recommend LiPo batteries with a max. length of 150mm and 50mm width.The conversion kits include all mechanical parts (except electric engine with speed control, Lipo batteries) to convert your FG model scale 1:5 and 1:6 to an electric powered system.
For converting the Sportsline long touring car into a model with 4WD drive. The conversion kit contains all chassis parts and drive parts that are required for the conversion.
Item N° 68503Conversions kit FG Leopard Sportsline 2WD to 4WD, setThis kit enables a conversion of the Leopard 2 into a Leopard 4 model with fourwheel drive. The conversion kit contents all chassis respectively drive components needed for the conversion.
The FG Touring and Sports cars at scale 1:5 are known for their high quality and very detailed bodyshells true to original. Also the technically fully developed chassis are worth mentioning. These models are now available with a high-torque brushless engine. Surface conditions with maximum grip assumed speeds above 100 km/h can be reached and steered controlled. E stands for electric power which is equivalent to extremely high torque, high speed and all this without any engine noise. The Sportsline models are equipped with a powerful brushless engine and a Brushless ESC. This control can be regulated simply via transmitter or optionally via the program card.T2M standard equipment brushless motor and ESC:
- ESC 150A controller 6S
- Brushless motor 6S You can order a motor/ESC combination with 8S for an additional charge. - ESC 200A, 3-8S LiPo, BEC 8A - Brushless Motor 8S You can select the car with complete RTR-equipment from the options menu. RTR equipment RTR = Ready to Run. The RTR version comes ready to use with the 2,4 GHz rc-system already installed. All E-Power versions need for the final assembling LiPo batteries and the suitable charger. For an unproblematic mounting we recommend to use LiPo batteries with a max. length 150mm and a width of 50mm. The model is delivered with an EC8 connector system.
Fits FG Monster and Stadium carsAre you owner of a Monster Truck or Monster Jeep, or perhaps of a Stadium Hummer? You are not really satisfied with the driving performance of your model, or you just want more driving fun? In this case we recommend to install the new 4WD conversion kit made by FG. The conversion kit includes all parts necessary to convert your 2WD Monster model to a 4WD model (complete front diff included). Assembly instructions are included.Fits the following FG cars:- Monster Truck- Monster Hummer- Monster Jeep- Monster Beetle Pro- Stadium Truck-Stadium Hummer- Stadium Jeep- Stadium Beetle ProPlease note: the radio plate is designed to accept a 805-sized servo (case length 65 mm). For installation of a Rhino (case length 58 mm) or a similar sized servo you need to order radioplate y0532 separately.The exploded view shows a partially assemled kit, therefore you can't see every single part included! The video shows the FG Off-Road Buggy 4WD during a test drive for a presentation in the Cars & Details magazine!The entire chassis is 100% identical to the FG cars Marder 4WD; Beetle 4WD and Monster / Stadium 4WDEnjoy the video!
Item N° 68511 Electric conversion kit 1:5 2WD with Wheelbase 465 to 535, setSuitable for the 2WD Touring sports cars and 2WD Race Trucks with a wheel base of 465 mm and 530/535 mm.This conversion kit is suitable for the 2WD 1:5 touring and sportscar models with 465mm - 530mm wheelbase. Suitable for the electric engines from FG Modellsport, Leopard BL engines and Castle Creation. The conversion kit includes gear and engine mount, fixing parts for cruise control and LiPo batteries.Cruise control, BL engine and LiPo batteries are not included.During the conversion several fixing holes have to be applied to the chassis. Gear transmission has to be changed accordingly to the use of the electric engine. For easy mounting we recommend LiPo batteries with a max. length of 150mm and 50mm width.The conversion kits include all mechanical parts (except electric engine with speed control, Lipo batteries) to convert your FG model scale 1:5 and 1:6 to an electric powered system.
The first 1/5 touring and sports car designed as a 4WD from the ground up. With a wheelbase of 510mm the 4WD chassis is suitable for the FG Mini Cooper and the FG Porsche GT3 RSR bodies. Equipped with a strong 26 cm³ engine, tuning pipe, tank with quick acting closure, 2 differential gears, front disk brake and a lot more. However, the highlight is still the well-known FG 4WD. Maximum traction, easy handling and grip during cornering as well, these are the advantages only a 4WD model can offer.You can select the car with complete RTR-equipment from the options menu. RTR-equipment RTR = Ready to Run. The RTR version comes ready to use with the 2,4 GHz rc-system already installed. Transmitter 2,4 GHzReceiverHigh power servo for throttle and brakeLargescale servo for steeringTx-battery, rx-battery The RTR version of the car includes servos, transmitter, receiver, rechargeable batteries for transmitter / receiver.The 4WD Sportsline chassis opens up a new era within the Touring and Sportscar class of large scale model cars. Main target was the development of a chassis with supreme driving dynamics and ultimate performance. Maximum traction as well as easy handling, sufficient grip in curves, only a fourwheel powered model offers all these advantages. With the new 4WD Sportsline series FG Modellsport once again sets a trend at 1:5 scale.The 4WD Sportsline chassis for the Porsche 911 GT3 RSR is delivered with a wheelbase of 510mm. The fourwheel drive is carried out over an almost wear resistant tooth belt. 2 differential gears, tank with snap closure and a powerful engine with Tuning pipe turn the Sportsline 4WD chassis into a high-class 1:5 scale model with outstanding driving characteristics.You can choose this 4WD model with painted bodyshell , 2.4 GHz radio control system, servos, batteries in our configurator. Team decals are not included in the delivery content and have to be ordered separately.The engine runs with a 2-stroke petrol-oil mixture. Through the installed pull-start system the engine can be started without any problems. A tank filling enables you to run your model around 45 minutes. Equipment and technical description:Solid 4mm chassis made of high-quality aluminium low-wear belt drive splash-proved 2 differential gears double wishbones at front and rear axle toe-in, castor and wheel camber adjustable at the axles - rear FG ball drive all steel driving components hardened all rotating parts ball-beared servo relieving servo saver front disk brake rear gear brake with big brake disk 700ccm fuel tank with snap closure oil-pressure shock absorbers with volume control and spring adjusting ring 26 cm³ combustion engine with Tuning pipe fabric hollow chamber tires with inserts receiver box and battery holder polycarbonate bodyshell 2.4 GHz pistol grip radio control system with steering and gas servo.Dimensions: Length: 980 mm Width: 405 mm Height: 250 mm Wheelbase: 510 mm HT-Edition? HT-Edition means: this version comes with a big set of spare / option parts included. Steel pinions - Non-standard sizesEach of two different ratios are supplied with.Modul: m=1,5Value: 62,60 EURAlloy engine mount smallCNC machined alloy engine mounts, direkt replacement for the stock plastic parts, heat and tweak resistant.Value: 54,90 EURDriveshaft bootsProtect ball drive as well as cardan drive against dirt. 4 pairs / 8 piecesValue: 42,90 EURAlloy spur gear carrierUse for 39T - 44 teeth spur gears.Value: 39,90 EURTotal value: 200,30 EURTouring cars in action!Painting tips:
The set includes: rear platedifferential mountsupper a-armslower a-armsinstallation hardware. Please note: must use inge pins 6075 instead of 6073! y0991for all FG 1/5 scale Sportsline 2WD touring cars, GT models (except Formular 1 and 1/6 scale Race Truck) The set includes:Rear platedifferential mountsupper a-armslower a-armsriser platesinstallation hardware.Please note: must use inge pins 6075 instead of 6073! y1003for all 1/6 scale Smartech Uno, Carson Attack, Super Attack, Gas Blaster and 1/5 scale Smartech/Carson touring car C5 and R5 models. The set includes: rear platedifferential mountslower a-armsupper a-armsinstallation hardware. Please note: must use inge pins 6075, also you need two packets turnbuckle 40 mm 6100/04y1205For Smartech 2WD Monster-Truck, Pick up Truck, Monster-Beetle, Comanche, CRT. The set includes: rear plate differential mounts lower a-arms upper a-arms steel turnbuckles for upper a-arms installation hardware. Please note: the hinge pins are not included, you will use the pins from the stock suspension!
Variants from €199.90*
€259.90*
This website uses cookies to ensure the best experience possible. More information.... By clicking on "[Agree / Accept all / etc.]" you also give your consent to the disclosure of your behavior in our store to our partner, shopware AG (Ebbinghoff 10, 48624 Schöppingen, Germany), which cannot assign this data to you personally, but may process it for its own purposes (e.g. product improvements, market behavior analyses).