LWR2017 SPEED TEC competition isolator set for all 1/5 & 1/6 engines exc. G320
Product information "LWR2017 SPEED TEC competition isolator set for all 1/5 & 1/6 engines exc. G320"
Genuine SPEED TEC spare/option part.
Aluminum isolator with PEEK (polyether ether ketone) inserts for the mounting bolts and two heat shielding plates.
The PEEK bushings and heat shielding plates guarantee an optimized thermal insulation of the carb compared to the stock isolator. This prevents fuel vapor locks even at high ambient tempratures, which usually results in engines running too lean; especially in the long run.
This isolator is highly recommended for competition use and any modified engine.
Total height of the complete unit, including heat shielding plates and all gaskets: 24.7 mm
Please note: does not fit Zenoah G320 engine!
Contents:
Aluminum isolator with PEEK (polyether ether ketone) inserts for the mounting bolts and two heat shielding plates.
The PEEK bushings and heat shielding plates guarantee an optimized thermal insulation of the carb compared to the stock isolator. This prevents fuel vapor locks even at high ambient tempratures, which usually results in engines running too lean; especially in the long run.
This isolator is highly recommended for competition use and any modified engine.
Total height of the complete unit, including heat shielding plates and all gaskets: 24.7 mm
Please note: does not fit Zenoah G320 engine!
Contents:
- Aluminum isolator with two PEEK inserts
- 2 x heat shielding plate
- 4 x gasket
- 2 x mounting bolt
- 2 x washer
Login
Similar products
This carburetor supoort sits beneath the air filter and prevents therefore widely arising vibrations.
Genuine FG spare/option part. Fits CY / Zenoah G230/240/260/270/290.Content:1 piece
SPEED TEC tuning insulator 26 mm, angled. Especially for 1/5 & 1/6 offroad cars The angled version is required for many offroad cars when installing a taller insulator and for HPI Baja series cars as well. The material components of this high quality engineering plastic, with an extremely high melting point of 280° C, guarantee optimal heat dissipation. Unlike the original insulator, this allows for a much better thermal insulation of the carburetor and therefore prevents fuel vapor lock in the carburetor at high ambient temperatures! The leaning of the engine at higher temperatures is counteracted! The 50% increased height and optimized port allows for lower fuel consumption! 60% glass fiber content of the SPEED TEC tuning insulator makes for strong mounting threads, providing a sturdy base for the usual airboxes or large off-road air filters which are common in competition applications. Kit includes: 1 x insulator 26 mm 1 x insulator gasket 1 x carburetor gasket 2 x allen head steel screws M5x25 2 x M5 serrated washers Please note:It is recommended to use a gasket sealer with every gasket on an engine. This gives better sealing anda longer lasting gasket. We also recommend:y0804 HT-flange sealer 518 y0994 Marston sealery0807 MD-Sil RTV silicone sealer
This reed valve system converts a normal piston-port engine into a reed valve engine. It offers the advantage of increased intake duration for a better charge for more power. As a positive side effect no fresh gas loss occurs during the downward movement of the piston because the membranes close this path.The reed valve block replaces the usual stock insulator. To use the advantage of the reed system, it is necessary to modify the piston skirt on the intake side. Depending on the engine it is advantageous for best results, to slightly match the cylinders intake port to the Epoxy insulator plate at the bottom of the reed valve system. Both steps are described in the installation instructions for Zenoah and Chung Yang engines. Our thanks for these instructions go to our customer Thomas Hoenicke.Note: For the time being the epoxy insulator plate must be slightly reworked to fit a G320 Zenoah engine. The manual has been written with the conversion of a G320, the affected area for modification is therefore shown.The unit is 24.5 mm high.
Genuine Mecatech spare/option part. Great reduction of heat transfer between cylinder and carburetor due the no connection of any metallic parts.Machined from billet heat resistant special polymer.Special duct geometry, completely machined on 5-axis cnc machine.Contents:1 piece
Genuine Speed-Tec spare/option part. SPEED TEC tuning insulator, slanted. Especially for 1/5 & 1/6 offroad cars The slanteded version is required for many offroad cars when installing a taller insulator and for HPI Baja series cars in general. The material components of this high quality engineering plastic, with an extremely high melting point of 280° C, guarantee optimal heat dissipation. Unlike the original insulator, this allows for a much better thermal insulation of the carburetor and therefore prevents fuel vapor lock in the carburetor at high ambient temperatures! The leaning out of the engine at higher temperatures is counteracted! The increased height and optimized port allows for lower fuel consumption!Due to the air boxes mandatory for racing and the required off-road air filters, a strong and rigid insulator is a must! No more stripped threads, no warpage and the resulting air leaks at the insulator anymore! So many weird running behaviors, for example if the engine is warmed up and a tiny gap occurred at the insulator, are caused by this distortion of a plastic insulator. The increased heat transfer of the aluminum is taken into account by addition of an insulator plate. Therefore the aluminum intake is largely insulated. Due to the face-milled surfaces of the aluminum intake you reach a greater durability of the gaskets.Please notice: the cylinder shroud y1016/021 must be reworked for angled tuning insulator!Dimensions:Height of aluminum intake 15 until 23 mmHeight of insulator plate: 6 mm Set includes: Aluminum intake insulator plate 3 x gasket 2 x allen screw 5 x 30 mm
Genuine Zenoah spare/option part. Replacement part fits Zenoah G320RC.
y1354 Version:
y1354/02 SPEED TEC Race
Genuine Speed-Tec spare/option part. Due to the air boxes mandatory for racing and the required off-road air filters, a strong and rigid insulator is a must! No more stripped threads, no warpage and the resulting air leaks at the insulator anymore! So many weird running behaviors, for example if the engine is warmed up and a tiny gap occurred at the insulator, are caused by this distortion of a plastic insulator. The increased heat transfer of the aluminum is taken into account by addition of an insulator plate. Therefore the aluminum intake is largely insulated. Due to the face-milled surfaces of the aluminum intake you reach a greater durability of the gaskets. The SPEED TEC aluminum insulator is available with two insulator plates.y1354/01 SPEED TEC cross aluminum insulator with 7 mm insulator plate and therefore a longer intake path for more torque. Ideal for off-road and cars. y1354/02 SPEED TEC Race aluminum insulator with 4 mm insulator plate, better for maximum rpm and therefore best for on-road use! Dimensions: Height of aluminum intake 20 mmHeight of cross version insulator plate - 7mm Height of Race version insulator plate - 3 mm Contents:Aluminum intake insulator plate 3 x gasket 2 x allen screw 5 x 30 mm 2 x washer 5/9.8 mm
Genuine Top Tuning spare/option part.The carburetor riser plate is made from 2 mm FRP; it improves the isolation of the carburetor against engine heat and strengthens the carburetor installation.Contents:1 piece
Genuine Speed-Tec spare/option part. The material component of this high quality engineering plastic, with an extremely high melting point of 280° C, guarantees optimal insulation. In contrast to the original insulator, this will greatly enhance the thermal insulation of the carburetor and therefore no vapor lock caused by a heated carb! The lean condition of the engine at high temps is counteracted! The larger by about 25% overall height of 26 mm (vs. 21 mm stock) and the optimized passage allow lower fuel consumption! The inner diameter has been enlarged compared to the stock insulator from 15.8 mm to 17.5 mm at the top! Due to the 60% glass fiber content of the SPEED TEC Tuning insulator the threads allow for high clamping force, therefore a secure fit is guaranteed even with air boxes or bigger off-road air filters, which are common in racing applications.Please note:It is recommended to use a gasket sealer with every gasket on an engine. This gives better sealing anda longer lasting gasket. We also recommend:y0804 HT-flange sealer 518 y0994 Marston sealery0807 MD-Sil RTV silicone sealerContents:1 piece
SPEED TEC racing insulator type C, with carburetor cooling, suitable for nearly all 1/5 & 1/6 cars (for very shallow body shells like Porsche GT or similar please use the 23 mm version # ST1011!) SPEED TEC O direct quote: According to our recent developments to reduce engine temperature, we now introduce our latest creation: the Speed Tec Tuning insulator C. Material and internal structure are identical to the original Speed Tec Tuning insulator 26mm. On the side facing the flywheel it has been extended and is provided with four holes. Air is passed through these holes directly from the fan towards the carburetor, which counteracts running lean at high ambient temperatures and improves performance. The insulator temperature is also lowered by the air passing through.The material components of this high quality engineering plastic, with an extremely high melting point of 280° C, guarantee optimal heat dissipation. Unlike the original insulator, this allows for a much better thermal insulation of the carburetor and therefore prevents fuel vapor lock in the carburetor at high ambient temperatures! The leaning of the engine at higher temperatures is counteracted! The 50% increased height and optimized port allows for lower fuel consumption! 60% glass fiber content of the SPEED TEC tuning insulator makes for strong mounting threads, providing a sturdy base for the usual airboxes or large off-road air filters which are common in competition applications.Minor modification of cylinder shroud is required! Kit includes: 1 x insulator 26 mm 1 x insulator gasket 1 x carburetor gasket 2 x allen head steel screws M5x30 2 x M5 serrated washers Please note:It is recommended to use a gasket sealer with every gasket on an engine. This gives better sealing anda longer lasting gasket. We also recommend:y0804 HT-flange sealer 518 y0994 Marston sealery0807 MD-Sil RTV silicone sealer
SPEED TEC tuning insulator 26 mm, suitable for nearly all 1/5 & 1/6 cars (for very shallow body shells like Porsche GT or similar please use the 23 mm version # ST1011!) The material components of this high quality engineering plastic, with an extremely high melting point of 280° C, guarantee optimal heat dissipation. Unlike the original insulator, this allows for a much better thermal insulation of the carburetor and therefore prevents fuel vapor lock in the carburetor at high ambient temperatures! The leaning of the engine at higher temperatures is counteracted! The 50% increased height and optimized port allows for lower fuel consumption! 60% glass fiber content of the SPEED TEC tuning insulator makes for strong mounting threads, providing a sturdy base for the usual airboxes or large off-road air filters which are common in competition applications. Kit includes: 1 x insulator 26 mm 1 x insulator gasket 1 x carburetor gasket 2 x allen head steel screws M5x30 2 x M5 serrated washers Please note:It is recommended to use a gasket sealer with every gasket on an engine. This gives better sealing anda longer lasting gasket. We also recommend:y0804 HT-flange sealer 518 y0994 Marston sealery0807 MD-Sil RTV silicone sealer
Customers also viewed
Genuine FG spare/option part. Made from T7075 aluminum with wide epoxy insulator plates to protect against engine heat transfer. Venturi-shaped bore increases engine performance.For easier installation removing the cylinder shroud is recommended .Contents:1 Set
SPEED TEC tuning insulator 26 mm, angled. Especially for 1/5 & 1/6 offroad cars The angled version is required for many offroad cars when installing a taller insulator and for HPI Baja series cars as well. The material components of this high quality engineering plastic, with an extremely high melting point of 280° C, guarantee optimal heat dissipation. Unlike the original insulator, this allows for a much better thermal insulation of the carburetor and therefore prevents fuel vapor lock in the carburetor at high ambient temperatures! The leaning of the engine at higher temperatures is counteracted! The 50% increased height and optimized port allows for lower fuel consumption! 60% glass fiber content of the SPEED TEC tuning insulator makes for strong mounting threads, providing a sturdy base for the usual airboxes or large off-road air filters which are common in competition applications. Kit includes: 1 x insulator 26 mm 1 x insulator gasket 1 x carburetor gasket 2 x allen head steel screws M5x25 2 x M5 serrated washers Please note:It is recommended to use a gasket sealer with every gasket on an engine. This gives better sealing anda longer lasting gasket. We also recommend:y0804 HT-flange sealer 518 y0994 Marston sealery0807 MD-Sil RTV silicone sealer
y1354 Version:
y1354/02 SPEED TEC Race
Genuine Speed-Tec spare/option part. Due to the air boxes mandatory for racing and the required off-road air filters, a strong and rigid insulator is a must! No more stripped threads, no warpage and the resulting air leaks at the insulator anymore! So many weird running behaviors, for example if the engine is warmed up and a tiny gap occurred at the insulator, are caused by this distortion of a plastic insulator. The increased heat transfer of the aluminum is taken into account by addition of an insulator plate. Therefore the aluminum intake is largely insulated. Due to the face-milled surfaces of the aluminum intake you reach a greater durability of the gaskets. The SPEED TEC aluminum insulator is available with two insulator plates.y1354/01 SPEED TEC cross aluminum insulator with 7 mm insulator plate and therefore a longer intake path for more torque. Ideal for off-road and cars. y1354/02 SPEED TEC Race aluminum insulator with 4 mm insulator plate, better for maximum rpm and therefore best for on-road use! Dimensions: Height of aluminum intake 20 mmHeight of cross version insulator plate - 7mm Height of Race version insulator plate - 3 mm Contents:Aluminum intake insulator plate 3 x gasket 2 x allen screw 5 x 30 mm 2 x washer 5/9.8 mm