Genuine CYS spare/option part. New ballraced digital servo with metal gears. Powerfull servo for steering applications in 1/5 and 1/6 scale cars, can be used for throttle/brake as well.voltage: 6 - 7,2 Vtorque: @ 7,2 V = 30 kg/cm / 6 V = 28 kg/cmspeed: 60° @ 6 V - 0,14 Sek.connector: Graupner-J/R + Robbe/Futabadimensions: 59,5 mm length, 29,2 width, 51,3 mm height154 grammsIdeal size for FG Sportsline and offroad / monster / stadium cars, all Carson / Smartech / Nutech / Conrad offroad or onroad cars and many other largescale cars as well. Digital-Power servo includes the following top equipment: One x double-sided 68 mm long servo horn, with 2,5 mm holes for linkage installation One x sigle-sided 42 mm long servo horn, with 2,5 and 3 mm holes for linkage installationFour x rubber grommets with 3 mm brass sleeves Four x mounting screws 3 x 14 mm Two x mounting screw 3 x 9 mm for the servo horn to the ballraced brass output shaft with Futaba/ds1015 spline sizevery strong 17-spline / 8,75 mm output shaftInstallation note: Always use the supplied rubber grommets and brass sleeves for installation of the Digital-Power servo!#6118/02 is required for FG 2WD offroad and monster cars, radio plate #y0532 for FG 4WD cars.Due to the high power of the Digital Power-Servo care must be taken that all wiring is up to the task. It is also absolutely mandatory to use the provided rubber grommets along with the brass bushing inserts for installation. (Replacement provided rubber and brass bushing: y0750/03)Contents:1 piece
Genuine Carson spare/option part. DimensionsLenght approx 63mmWidth approx 33mmHeight approx 55mmThe stronger alternative:K-Power DM4000 Servo 54kg-cm/0,11 s/6 Volt till 8,4 volt 89,90 EURHowever, the installation requires some "rework" on the servo mount!Contents:1 piece
Genuine HT spare/option part. Protects the mated connection to prevent them from coming apart accidentally. Particularly recommended for direct power supply cords, as a tensile load on the cable can remove the link unnoticed and then you would perhaps think of a servo failure in the first place.The small size usually allows the installation even inside the receiver box.Also suitable for securing the connection of the receiver battery; the use of this clip means a big improvement in safety with little effort.Contents:1 piece
Genuine HPI spare/option part. Distances bore to center of servo horn: 26 and 31 mm. Holes tapped with M3 thread.This aluminum steering arm is built extra tough to handle the demands of 1/5th scale vehicles. Use it as a replacement part on the Baja 5T HPI SFL-10MG2 servo, or as an upgrade to the stock plastic servo arm used on the SFL-10 and HPI SFL-MG servos. HPI recommends upgrading to the metal servo gears if upgrading the stock plastic servo arm.Contents:1 piece
Genuine HT spare/option part.Extreme duty gears for largescale offroaders and monster trucks. Set of coarse pitch pinion for the layshaft and corresponding differential spur gear, especially for use in off-road and monster models. The teeth are stronger and , due to their bigger size, a little bit more forgiving when the gear mesh is not adjusted correctly.Module: m=1,75To keep the original gearing the set is available with 12 teeth pinion for Monster Truck & Co. or 13 teeth pinion for all other off-roaders with standard sized tires.The differential spur gear has 41 teeth. Please tell us your choice!Fits FG 2WD cars and Carson Attack/Firehammer/Smartech Traveller, Carson Comanche, Touareg a.s.o. The gears have diameters like standard units.Contents:2 pieces [INCLUDE]profilverschoben[ENDINCLUDE]
Genuine HT spare/option part.These servo mounts allow for a simple and strong mounting of the Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP high power servo for steering application.The massive servo mounts bolt to the chassis using existing mounting holes. The mount for the stock servo has to be cut off the radio plate. The aluminum servo mounts feature a pair of additional mounting holes to install a stock servo should ever the need arise. The rear mount bolts to the radio plate as well, providing additional support for the plate.Scope of delivery y1308/01:1 x Mount A2 x Socket head cap screws 3 x 16 mm2 x Countersunk screw 4 x 14 mm2 x Shim ring 4,2 mmScope of delivery y1308/02:1 x Mount B1 x Socket head cap screw 3 x 25 mm1 x Socker head cap screw 3 x 16 mm2 x Countersunk screw 4x14 mm2 x Shim ring 3,2 mmContents:1 set
Our 4WD models are attractive and very popular. The wheelbase of the WB535 version is 40 mm longer. This modification improved the directional stability as well as further driving qualities significantly. Equipment of the modelAngled 4 mm alloy chassis with countersunk borings at the bottom, 4-wheel belt drive, belt drive cover, differential gear at front and rear axle with hardened bevel gearwheels, closed front axle housing, closed belt drive at the rear, adjustable double wishbones at front and rear axle, all driving parts and gearwheels made of case-hardened steel, adjustable servo saver, 4 adjustable oil-pressure shock absorbers, rear gear brake, alloy side plates, Monster tires with chrome-plated rims, polycarbonate body shell, decal set.You can select the car with complete RTR-equipment from the options menu. RTR-equipment RTR = Ready to Run. The RTR version comes ready to use with the 2,4 GHz rc-system already installed. Transmitter: Reflex Wheel Pro III 2,4 GHzReceiver: Mini BECHigh power servo for throttle and brakeLargescale servo for steeringTx-battery, rx-battery The model is equipped with a original 26 cm³ Chung-Yang (series engine) combustion engine with muffler and ready-for-use oiled filter. The engine runs with normal 2-stroke petrol-oil mixture (available at every petrol station). The tank filling of 0,7 litres enables you to run your model around 45 minutes. With the installed pull-starter system the engine can be started without any difficulties.The pictures may display the car with some optional items which are not included, like bed-mounted rollbar, lights, front bumper or mirrors. These items can be added in the drop down menus.The RTR-version is delivered with assembled and preset radio control system and rechargeable batteries. to complete the non-RTR version all popular servos and radio control systems are suitable.HT-Edition? HT-Edition means: this version comes with a big set of spare / option parts included. Steel pinions - Non-standard sizesEach of two different ratios are supplied with.Modul: m=1,5Value: 62,60 EURAlloy engine mount smallCNC machined alloy engine mounts, direkt replacement for the stock plastic parts, heat and tweak resistant.Value: 54,90 EURDriveshaft bootsProtect ball drive as well as cardan drive against dirt. 4 pairs / 8 piecesValue: 42,90 EURAlloy spur gear carrierUse for 46T - 48 teeth spur gears.Value: 39,90 EURTotal value: 200,30 EURDimension:Length: 780 mmWidth: 510 mmHeight: 350 mmWheelbase: 535 mm