Genuine HT spare/option part. RC Tech Pipe Protect protects your exhaust against oil and rubber deposit while racing. A clean exhaust gives better resonance, which means better performance from your engine. Thanks to RC Tech Pipe Protect your exhaust system can evacuate the temperature better.Direction of useSpray a relatively thick layer of Pipe Protect from a close distance; +/- 15/20 cm on your new or just-cleaned and preferably polished exhaust pipe. After each ride clean the exhaust pipe with a clean cloth, if necessary slightly sprayed with some Pipe Protect. Treat the exhaust pipe again before each race.Contents:1 piece / 400 ml
Especially for installation of all engine gaskets. Temperature resistant from -55 °C to +200 °C. Resistant to water, mineral oils, synthetic lubricants, fuels, organic solvents and refrigerants. info: Hand tight: 10 - 20 minReady to use: 1 - 3 hoursGap fill: 0.5 mmContent: 50 ml Notes for usage: This surface seal is not for use as the sole sealant, it should always be applied in combination with a paper gasket.The HT-surface sealing agent should be sparsely applied over the entire surface, with care being taken that the sealant does not enter the devices internals (e.g. crankcase, differential a.s.o.) during the assembly.
Genuine FG spare/option part. Newly developed tuned pipe made of strong steel sheet, with plug connecting system. The pipe mounts close to the car for best protection possible and versatile usability. Suitable for:FG 2WD and 4WD 1:6 Off-RoadSmartech 2WD off-road And for many other brand's 1/6 carsNot suitable for:FG Leopard2 2+4 WD Sportsline and CompetitionOn several pictures the pipe is shown with a silicone tube tailpipe extension, which is not included. It can be ordered separately as an accessory with part number 6299/03 or y0995.Content:1 piece
Genuine FG spare/option part. Spare part for FG Leopard 4WD 2010. Fits for FG Sportsline 4WD 510/530.FG fuel tank #8383 along with tank mount #69238/01 is required for installation on a Leopard 4WD Sportsline. The receiver battery must be relocated as well.Mielke #5062 is required for installation of this pipe.Contents:1 set
The brushless Big Scale servo is an extremely robust digital servo, with a high performance brushless motor, in absolute premium quality, with a full aluminum case for optimal heat dissipation in the 2-version with elaborate cooling fins, metal gears and equipped with high-quality 30 cm long silicone insulated cable. Where with other high-performance servos you still have to buy an aluminum top or case as third party options, the brushless Big Scale servo already comes with a full metal case, and above all, the aluminum to features special bushings for the intermediate shafts! Of course, the support from a metal top cover guarantees a much longer service life of the complete gearbox, than with a plastic version! Defective gears are known to be the most frequent cause of failure; especially for highly stressed servos in 1/5 and 1/6 cars! The brushless Big Scale servo is also the first choice for 1/8 and 1/10 race cars, where fast reaction times and high steering forces bring up the demand for an extremely fast and reliable servo! Also, servo mounting tab breakage on the servo cover is virtually impossible with the brushless Big Scale servo. Dimensions:Length: 40 mmWidth: 20 mmHeight: 41.4 mmWeight: 72 gramsPerformance:7.4 V6 VHolding torque kg-cm/oz-in30.0/41726,0/361Speed sec./60°0.110.14Accessories included:Three different plastic servo horns / discFour each rubber grommets and guide sleevesMounting screwsNote: Due to the extreme holding power of the brushless Big Scale servo the rubber grommets should always be installed in combination with the guide sleeves. The brushless Big Scale servo comes with accessories in a high quality plastic case with molded insert.We recommend an aluminum servo arm from the selection of the article:Alloy servoarms, for 25 teeth multi-tooth shaft 9,90 EUR
€99.90*
€129.90*(23.09% saved)
This website uses cookies to ensure the best experience possible. More information...