Genuine HT spare/option part. RC Tech Pipe Protect protects your exhaust against oil and rubber deposit while racing. A clean exhaust gives better resonance, which means better performance from your engine. Thanks to RC Tech Pipe Protect your exhaust system can evacuate the temperature better.Direction of useSpray a relatively thick layer of Pipe Protect from a close distance; +/- 15/20 cm on your new or just-cleaned and preferably polished exhaust pipe. After each ride clean the exhaust pipe with a clean cloth, if necessary slightly sprayed with some Pipe Protect. Treat the exhaust pipe again before each race.Contents:1 piece / 400 ml
Genuine FG spare/option part. Spare part for FG Leopard 4WD 2010. Fits for FG Sportsline 4WD 510/530.FG fuel tank #8383 along with tank mount #69238/01 is required for installation on a Leopard 4WD Sportsline. The receiver battery must be relocated as well.Mielke #5062 is required for installation of this pipe.Contents:1 set
Regular price: [ITEMPRICE]SELF[ENDITEMPRICE] EUROffer of the month price: [ITEMDISCOUNTPRICE]SELF[ENDITEMDISCOUNTPRICE] EURTypical featuresLow inner resistance with high MPVHigher energy density with lower weightLonger lifecycle under proper usage, up to 200 timesFor LiPo batteries, the peak amp rate is usually twice the continuous crateCan be charged with 5C when time is criticalRecommended charge with 2 3C (max. 3C)Spezification:Tension: 3S / 11,1VCapacity mAh: 3300Case: SoftCable cross section: 12AWG/3,3Length +/- 5 mm: 135 mmWidth +/- 1,5 mm: 45 mmHeight: +/- 1,5 mm: 25 mmWeight +/- 10g: 280gCont. current: 20C (115,5A)Contents:1 piece
Item N° 67299/03Aluminum exhaust mount 4WD, setRugged aluminum exhaust mount for the Leopard 4WD Competition car. Replaces the exhaust installation using piano wires.
With this robust and reliable FG chassis, which is equipped with a powerful 26 cm³ combustion engine, you get the ideal entry into the fascinating "royal class" of large scale RC models as well as into the competition.The model has a 510 wheelbase. The models are built on a 4 mm alloy chassis with double wishbones at front and rear axle. All borings of the alloy chassis are countersunk to prevent the screw heads from bearing out. The models are serial equipped with the 2-damper front axle which guarantees an optimal traction of both front wheels. At the front/rear axle you can adjust through track rods or adjusting screws with right-/left-handed thread the king pin angle, trailing effect and toe-in.Further equipment points are differential gear, 24 teeth steel pinion, oil-pressure shock absorbers with volume control and external adjusting ring for the initial spring preload. All rotating parts as shafts, axles and clutch bells a.s.o. are supported by ball bearings.The remote control, the two servos and the receiver battery (RTR set!) are required to operate the FG model. This RTR equipment is available in our shop selection for an additional fee.The body shell is clear, but also available in a painted version in our shop selection for an additional fee.Thanks to the numerous available option parts, you can upgrade your FG Challenge Line as required.You can select the car with complete RTR-equipment from the options menu. RTR-equipment RTR = Ready to Run. The RTR version comes ready to use with the 2,4 GHz rc-system already installed. Transmitter: Reflex Wheel Pro III 2,4 GHzReceiver: Mini BECHigh power servo for throttle and brakeLargescale servo for steeringTx-battery, rx-battery Dimensions:Length: 870 mmWidth: 392 mmHeight: 260 mmWheelbase: 510 mm