6427 FG Plastic gear wheel 46 teeth - 1pce.

€17.90*

Prices incl. VAT plus shipping costs

Available

Product number: fg_6427

EAN: 3410564508404

Product information "6427 FG Plastic gear wheel 46 teeth - 1pce."

46 teeth gear wheel for the layshaft.
Diameter 72 mm
Width 15.5 mm
Tooth width 12 mm
Module: m=1,5

0 of 0 reviews

Leave a review!

Share your experiences with other customers.

Login

Your email address

Your password

No reviews found. Share your insights with others.

Accessories / Spare parts

y0190/46 HT-Alloy carrier with steel spur gear 46T for the layshaft

This carriers makes it possible to run steel spur gears on the layshaft. Pebbles heat and the high torque of monster truck applications are no longer a problem.The carrier is designed for reverse installation as seen on the FG EVO car, where the hubs of the pinion and the spur gear carrier are pointing to the outside of the car. The carrier features M8 (eight, no typo) grub screws for installation on the layshaft. This means that the tip of the screw is as wide as the flat area on the shaft and ensures best possible load distribution.

€89.90*

6492 FG Steel spur gear 46T with adapter - set

Hardened steel spur gear for FG 1/6 off-road models, spur gear diameter 72 mm.Module: m=1,5

€97.90*

Alternatives

y0190/46 HT-Alloy carrier with steel spur gear 46T for the layshaft

€89.90*

6492 FG Steel spur gear 46T with adapter - set

Hardened steel spur gear for FG 1/6 off-road models, spur gear diameter 72 mm.Module: m=1,5

€97.90*

Similar products

7427 FG Plastic gearwheel 40 teeth

Genuine FG spare/option part.Suitable for all 1:5 models.Dimensions:Diameter 63 mmWidth 15.5 mmTooth width 12 mmModule: m=1,5Contents:1 piece

€17.90*

7052 FG Plastic gear wheel 42 teeth - 1pce.

Gearwheel with 42 teeth for the layshaft. Diameter 66 mmWidth 15.5 mmTooth width 12 mmModule: m=1,5

€15.75*

6052 FG Plastic gearwheel 48 teeth

Genuine FG spare/option part. Stock spur gear for all FG monster cars.Suitable for spur gear carriers: 6050 (plastic) 6439 (aluminum)Dimensions:Diameter: 75 mmWidth: 15.5 mmTooth width: 12 mmModule: m=1,5 Contents:1 piece

€17.90*

6422/01 FG Plastic gearwheel 44 teeth 2-speed - 1pce.

44 teeth plastic main gear for the layshaft with 2-speed gear.Diameter 69 mmWidth 15.5 mmTooth width 12 mmModule: m=1,5

€17.90*

7427/01 FG Plastic gearwheel 40 teeth 2-speed - 1pce.

Suitable for all 1:5 models with 2-speed gear.Diameter 63 mmWidth 15.5 mmTooth width 12 mmModule: m=1,5

€17.90*

Details

7424 FG Plastic gearwheel 38 teeth

Genuine FG spare/option part.Suitable for all 1:5 models. Requires gear carrier 7423.Dimensions:Diameter: 60 mmWidth: 15,5 mmTooth width: 12 mmModule: m=1,5Contents:1 piece

€17.90*

7052/01 FG Plastic gear wheel 42 teeth 2-speed

Genuine FG spare/option part. Gearwheel with 42 teeth for the layshaft. Only for the 2 speed box.Dimensions:Diameter: 66 mmWidth: 15,5 mmTooth width: 12 mmModule: m=1,5Content:1 piece

€15.50*

6427/01 FG Plastic gear wheel 46 teeth 2-speed

Genuine FG spare/option part. 46 teeth gear wheel for the layshaft with 2-speed gear box.Dimensions:Diameter: 72 mmWidth: 15.5 mmTooth width: 12 mmModule: m=1,5Contents:1 piece

€19.50*

6422 FG Plastic gearwheel 44 teeth - 1pce.

44 teeth plastic main gear for the layshaft.Diameter 69 mmWidth 15.5 mmTooth width 12 mmModule: m=1,5

€17.90*

6052/01 FG Plastic gearwheel 48 teeth 2-speed

Genuine FG spare/option part. For 2-speed gear box only. With 75 mm diameter.Module: m=1,5.Contents:1 piece

€17.90*

7425 FG Plastic gearwheel 39 teeth - 1pce.

Suitable for all 1:5 models.Diameter 63 mmWidth 15.5 mmTooth width 12 mmModule: m=1,5Profile regraded, this means that the number of teeth is changed while the diameter remained constant. The part of the involutes? curve that defines the tooth profile is changed. Positively regraded (lower number of teeth) pinions are stronger and run smoother, the reduced strength of negatively regraded pinions doesn?t really matter.

€17.90*

This product is currently not available.

7429 FG Plastic gearwheel 41 teeth - 1pce.

Suitable for all 1:5 models. With 63 mm diameter.Module: m=1,5Profile regraded, this means that the number of teeth is changed while the diameter remained constant. The part of the involutes? curve that defines the tooth profile is changed. Positively regraded (lower number of teeth) pinions are stronger and run smoother, the reduced strength of negatively regraded pinions doesn?t really matter.

€17.90*

Customers also viewed

7316 FG Clutch blocks for Zenoah

Genuine FG spare/option part. Zenoah bolts 7318 are required for installation.Content:2 pieces

€19.90*

TT0990 Top Tuning Failsafe with kill switch and status LED for all transmitters

Genuine TT spare/option part.The new and improved failsafe modul.This kill switch module works with most FM and 2.4 GHz rc-systems. Not compatible with AVC-equipped receivers! You must have a free channel on your rc-system in order to install the module! This means at least a 3-channel radio for standard 1-servo brake/throttle setups or a 4-channel radio for dual brake servos driven by the radio's mixer function. With this module you can stop the engine with your radio. Additionally the module features a failsafe function which stops the engine when the rx-battery's voltage drops below a certain level or the rc-system has a glitch. A kill switch module fulfils two tasks. On the one hand, as a safety device, it is intended to shut off an engine with magneto ignition in case of failure of the remote control, and on the other hand, the engine can be stopped at any time by remote control.While the latter is mainly used for convenience, the safety aspect is what really matters.The failsave circuit integrated in all modern remote controls may brake the vehicle in the event of a radio interference, but this feature is dependent on the basic functionality of the receiver system and its power supply. However, if the receiver, the gas servo or the power supply fails completely, the failsave of the remote control can no longer do its job. The vehicle may be running haywire at full throttle.In these cases, the kill switch will cut the ignition of the engine and the vehicle will roll out without power.Features:Ready to install no soldering requiredRemote LED for easy-to-spot operational status (ignition live/killed)Optically coupled to isolate the ignition from the radio systemThreshold value for undervoltage protection (4V, 5V, 6V) adjustable with jumpers allows adaptation to the rx-battery type (LiPo, LiFePo, NiMH, NiCd)Contents:1 piece

€34.90* €42.90* (18.65% saved)

5785 FG Chung Yang engine V260/CY 4 Bolt Version

Genuine FG spare/option part.Genuine FG/Chung Yang V260 engine, 26 cm³, 4-bolt head.This is the current stock engine of all 1/6 FG off-road and monster cars.

€199.90*

7472 FG Tuning clutch bell hardened

Genuine FG spare/option part. Case-hardened Tuning clutch bell in high quality steel. Borings for cooling and a reinforced outside diameter ensure shape stability at high speed. Suitable for all 1:5 and 1:6 models except Formula 1.Shaft 10 x 38 mmFlat sections for set screws with 90° offsetContent:1 piece

€64.90*

7430/24 FG Alloy gearwheel 24 teeth

Genuine FG spare/option part. Extreme light alloy gear wheel in anodizing quality with 24 teeth.Suitable for the gear wheels with 39, 40 and 41 teeth.Dimensions:Diameter: 38,7 mmBore: 10 mmTotal width: 18 mmTooth width: 11,5 mmModule: m=1,5Contents:1 piece

€30.20*

7039/01 FG Gear plate 97 - 1pce.

Also available in .Current version for brake with one large disc.

€19.80*

This product is no longer available.

ST1014 SPEED TEC Racing insulator type C with carburetor cooling

SPEED TEC racing insulator type C, with carburetor cooling, suitable for nearly all 1/5 & 1/6 cars (for very shallow body shells like Porsche GT or similar please use the 23 mm version # ST1011!) SPEED TEC O direct quote: According to our recent developments to reduce engine temperature, we now introduce our latest creation: the Speed Tec Tuning insulator C. Material and internal structure are identical to the original Speed Tec Tuning insulator 26mm. On the side facing the flywheel it has been extended and is provided with four holes. Air is passed through these holes directly from the fan towards the carburetor, which counteracts running lean at high ambient temperatures and improves performance. The insulator temperature is also lowered by the air passing through.The material components of this high quality engineering plastic, with an extremely high melting point of 280° C, guarantee optimal heat dissipation. Unlike the original insulator, this allows for a much better thermal insulation of the carburetor and therefore prevents fuel vapor lock in the carburetor at high ambient temperatures! The leaning of the engine at higher temperatures is counteracted! The 50% increased height and optimized port allows for lower fuel consumption! 60% glass fiber content of the SPEED TEC tuning insulator makes for strong mounting threads, providing a sturdy base for the usual airboxes or large off-road air filters which are common in competition applications.Minor modification of cylinder shroud is required! Kit includes: 1 x insulator 26 mm 1 x insulator gasket 1 x carburetor gasket 2 x allen head steel screws M5x30 2 x M5 serrated washers Please note:It is recommended to use a gasket sealer with every gasket on an engine. This gives better sealing anda longer lasting gasket. We also recommend:y0804 HT-flange sealer 518 y0994 Marston sealery0807 MD-Sil RTV silicone sealer

€39.90*