6492/01 FG Steel spur gear 46T - 1 pce.

Item N° 6493/01 Steel spur gear 48T - 1 pce.Outer diameter: 75 mmInner diameter: 26 mmBolt circle: 3 x 35 mmWidth: 10 mmModule: m=1.5

Nitrided hardened, highly wear-resistant.Not suitable for Smartech and Carson models.  Suitable for FG offroad models 2WD on the clutch bell to the 42 main gear.  This pinion is profile shifted and has a 1.5 module.  This means that the number of teeth of the gear is changed compared to the previously known values while the diameter remains the same. The area of the involute curve that determines the tooth profile is shifted. Positively shifted gears (fewer teeth than normal) are more stable and run more smoothly; the slightly lower strength of negatively shifted gears is irrelevant.  1 piece

Contents:1 set

Genuine FG spare/option part.For combination with 48T main and differential spur gear.Diameter: 26.7 mmBore: 10 mmTotal width: 16 mmTooth width: 9.5 mmModule: m=1,5Contents:1 piece

To celebrate the 30th anniversary of the legendary Marder 1/6 scale 2WD buggy, FG Modellsport/T2M releases a special edition, limited to 300 numbered pieces, with the original signature of Franz Gröschl on the sticker sheet as well as a top equipment (G260RC Zenoah engine, hi-capacity low friction aluminum shock absorbers and special aluminum engine mounts). with original 260 Zenoah with Low-Friction Alu shocks with alloy enginemount The Models is built on a 4 mm u-bended chassis. All borings of the lower side are countersunk, therefore the screw heads can't bear out.Double wishbones at font and rear axle as well as 4 bulk oil-pressure shock absorbers guarantee perfect ground adherence. All rotating parts are supported by ball-bearings. Rear gear wheels, differential gears and all driving elements are case-hardened. The side guards protect the model from dirt. With original signature of Franz Gröschl. The model is equipped with a powerfull 26 ccm engine which runs with normal 2-stroke petrol-oil mixture (available at every petrol station). The tank filling of 0,7 liters enables you to drive about 45 minutes. The engine can be started without difficulties through the integrated pull-start. To complete the models all merchantable servos and radio control systems are suitable.You can select the car with complete RTR-equipment from the options menu. RTR-equipment RTR = Ready to Run. The RTR version comes ready to use with the 2,4 GHz rc-system already installed. Transmitter 2,4 GHzReceiverHigh power servo for throttle and brakeLargescale servo for steeringTx-battery, rx-battery

Original TopTuning spare/option part. Carburetor heat sink for all Zenoah/CY/HPI/Losi and PT-Smartech/Carson engines.Fits all Walbro 603/813/990/771/527/1107 carburetors as well as all Smartech/Carson PT engine carburetors and many more!The TopTuning carburetor heat sink counteracts the notorious vapor lock at high engine temperatures.In fact all current large scale engines have a special adaptor for the thermal insulation of the carb (isolator) to keep the carb as cool as possible, so that the fuel does not form bubbles due to heat transfer from the cylinder. And without this isolator the gasoline would literally cook after a short operating time and therefore the engine would receive a leaner mixture. The much feared lean-out until the engine stalls is inevitably.Unfortunately, even a special isolator is often insufficient at higher ambient temperatures or when the engine is subjected to higher loads, e.g. in racing. In such scenarios the better heat dissipation of the Top Tuning carburetor heat sink contributes to the solution of the problem.The easy to install heat sink, requires a considerable manufacturing and milling effort and fits easily to all common 1:5/1:6 large scale cars, such as FG, Mecatech, Smartech/Carson, HPI, Losi, etc..For installation in FG 4WD cars the rear cross member # 66212 must be modified.Attention: the Allen head screw is an imperial size and therefore not compatible with metric Allen wrenches! Available in our options menu Content: Carburetor heat sink 1 x Allen head screw #8-32 x 5/8" (for Walbro carbs) 1 x washer 4 mm

Item N°6490 Alloy spur gear adaptorLength 26.5 mmBore 10 mmBolt circle for spur gear 3 x 35 mm, M5 thread